Lightolier 1190 User manual

Lightolier
Brand
Lightolier
Model
1190
Category
Work lights
Type
User manual

Lightolier 1190 is a lighting fixture designed for installation in accordance with the National Electrical Code and local regulations. It is intended for use with specific reflector trims provided by Lightolier, and the use of other manufacturers' reflector trims may void the Underwriters Laboratories listing and could constitute a fire hazard.

The Lightolier 1190 can be installed in frame-in kits (FIKs) with Roto-clips or socket cup spring legs. For installations in FIKs with Roto-clips, the Roto-clips should be rotated so that the short legs extend inwardly toward the center opening.

Lightolier 1190 is a lighting fixture designed for installation in accordance with the National Electrical Code and local regulations. It is intended for use with specific reflector trims provided by Lightolier, and the use of other manufacturers' reflector trims may void the Underwriters Laboratories listing and could constitute a fire hazard.

The Lightolier 1190 can be installed in frame-in kits (FIKs) with Roto-clips or socket cup spring legs. For installations in FIKs with Roto-clips, the Roto-clips should be rotated so that the short legs extend inwardly toward the center opening.

1
FRAME-IN KIT (FIK) INSTALLATION: See Frame-In Kit Instruction Sheet for installation procedure.
2 INSTALLATION IN FIK’S WITH ROTO-CLIPS:
A. Rotate (4) Roto-clips so that the short legs extend inwardly toward center opening.
B. Remove lens holder assembly from trim by pulling lens holder assembly away from housing then
squeezing Torsiontite springs together and removing from slots in housing.
C. Insert FIK socket cup into neck of trim making sure springs of socket cup snap into the slots of trim.
D. Push trim straight up until it is tight against ceiling.
E. Reinstall lens holder assembly by squeezing Torsiontite springs and inserting through housing slots.
F. NOTE: To remove trim from ceiling, first remove lens holder assembly as in Step B above, then turn
trim counterclockwise while pulling downward.
Figure A
Figure B
Figure C
Figure D
Figure E
3 INSTALLATION IN 1104 AND 1004 SERIES FIK’s W/ SOCKET CUP SPRING LEGS:
A. Remove lens holder assembly from trim by pulling lens holder assembly away from housing then
squeezing Torsiontite springs together and removing from slots in housing.
B. Insert FIK socket cup into neck of trim making sure springs of socket cup snap into the slots of trim.
C. Push trim straight up until it is tight against ceiling.
D. Reinstall lens holder assembly by squeezing Torsiontite springs and inserting through housing slots.
E. To remove trim from ceiling, first remove lens holder assembly as in Step A above, squeeze reflector
spring clip from inside until the trim disengages.
NOTE: To retrieve socket cup, pull on one of the socket cup spring legs to disengage.
Figure A
Figure B Figure C
Figure D
Figure E
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTALLATION PROCEDURE FOR: 1190, 1090
1190 for use with 1100AICM/DICM/IC, 1102P1, 1103R, and 1104IC/ICR/ICX only.
1090 for use with 1000AICM/IC, 1002P1, 1003R and1004IC/ICR/ICX only.
CAUTION: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S REFLECTOR
TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
INSTRUCTION SHEET NO.
IS:1190
A0605
Page 1 of 1
A COMPANY
631 Airport Road, Fall River, MA 02720
CAUTION: BEFORE INSTALLING REFLECTOR TO FRAME-IN-KIT, READ MARKINGS IN REFLECTOR AND IN SOCKET CUP
OF FRAME-IN-KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION.
CAUTION: (RISK OF FIRE) FOR NON-IC RATED INSTALLATIONS, DO NOT INSTALL INSULATION ABOVE
OR WITHIN 3 INCHES OF ANY PART OF FIXTURE.
  • Page 1 1

Lightolier 1190 User manual

Lightolier
Brand
Lightolier
Model
1190
Category
Work lights
Type
User manual

Lightolier 1190 is a lighting fixture designed for installation in accordance with the National Electrical Code and local regulations. It is intended for use with specific reflector trims provided by Lightolier, and the use of other manufacturers' reflector trims may void the Underwriters Laboratories listing and could constitute a fire hazard.

The Lightolier 1190 can be installed in frame-in kits (FIKs) with Roto-clips or socket cup spring legs. For installations in FIKs with Roto-clips, the Roto-clips should be rotated so that the short legs extend inwardly toward the center opening.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents