AMX DXLink User manual

Instruction Manual

DXLink™ Twisted Pair Transmitters/Receiver

DXLink

™

Twisted Pair

Transmitters/Receiver

DXLink Multi-Format Wallplate Transmitter

DXLink Multi-Format Decor Style Wallplate Transmitter (US)

DXLink Multi-Format Transmitter Module

DXLink HDMI Transmitter Module

DXLink HDMI Receiver Module

REV N: 03/17/2014

AMX Domestic Channel Partner Limited

Warranty, Disclaimer and License

(Excerpt from CHANNEL PARTNER TERMS AND CONDITIONS Versions 11.17.2011 with updates for previous

version 8.25.2010 [sections 6.1 (a), (b) and (f)])

6. LIMITED WARRANTY; RETURN, REPAIR AND REPLACEMENT

6.1 AMX warrants the Products to be free of material defects in materials and workmanship under normal use

for three (3) years from the Shipping Date (or such other period as may be specified below), subject to the

following limitations and exceptions (“Limited Warranty”). For any Product, “Warranty Period” means the

period during which the Limited Warranty is in effect, as set forth herein.

(a) LCD and LED panels are warranted for three (3) years from the Shipping Date, except for the display

and touch overlay components, which are warranted for a period of one (1) year from the Shipping

Date.

(b) Disk drive mechanisms, pan/tilt heads and external power supplies are warranted for a period of

one (1) year from the Shipping Date.

(c) AMX lighting Products are warranted to switch on and off any load that is properly connected to our

lighting Products, as long as the AMX lighting Products are under warranty. AMX also warrants the

control of dimmable loads that are properly connected to our lighting Products. The dimming

performance or quality thereof is not warranted, due to the random combinations of dimmers, lamps

and ballasts or transformers.

(d) AMX software and firmware included in the Products is warranted for a period of ninety (90) days from

the Shipping Date.

(e) Batteries and incandescent lamps are not covered under the Limited Warranty.

(f) The Warranty Period for AMX AutoPatch EPICA, Enova DGX, Modula, Modula Series 4,

Modula Cat Pro Series and 8Y-3000 Product models will continue for the original installation until

five (5) years after the issuance of a PDN with respect to termination of the applicable Product model.

However, if the Product is moved from its original installation to a different installation, the Warranty

Period will automatically become three (3) years from the Shipping Date and, if more than three (3)

years have elapsed since the Shipping Date, the Warranty Period will automatically expire.

Version Date: 11-17-11

Note: The complete Warranty is at www.amx.com.

Contents

3

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Contents

ESD Warning.......................................................................................................................6

Important Safety Information and Instructions ...................................................................7

Information et directives de sécurité importantes..............................................................8

Notices ...............................................................................................................................9

Product Overview and Specifications ...............................................................................11

Applicability Notice ................................................................................................................................. 11

Product Notes.......................................................................................................................................... 11

Product Compatibility Tables................................................................................................................... 12

DXLink Transmitter and Receiver Features .............................................................................................. 13

Common Applications.............................................................................................................................. 14

Transmitters............................................................................................................................................. 14

Receiver ................................................................................................................................................... 22

Common Features/Functionality .............................................................................................................. 25

Quick Reference Tables for Modes .......................................................................................................... 28

DXLink Transmitters and Receiver Specifications .................................................................................... 30

Installation and Setup .......................................................................................................36

Site Recommendations ............................................................................................................................ 36

General Hazard Precautions..................................................................................................................... 36

Setup Information.................................................................................................................................... 37

Wallplate Transmitters – Attaching Signal/Transport Cables ................................................................... 53

Multi-Format TX or HDMI TX – Attaching Signal, Transport, and Control Cables.................................... 55

Multi-Format TX or HDMI TX – Applying Power ...................................................................................... 56

HDMI RX – Attaching Signal and Control Cables ..................................................................................... 57

HDMI RX – Applying Power ..................................................................................................................... 58

Serial Data Transfer and IR Flow Control ................................................................................................. 59

Optional: Multi-Format TX, HDMI TX, and HDMI RX –

Wiring for Serial Data Transfer ..................................................................................................................... 59

Optional: Multi-Format TX, HDMI TX, and HDMI RX – IR Control ........................................................... 60

ID Pushbutton Functions.......................................................................................................................... 61

HDMI RX Scaling Button and Scaling Modes ........................................................................................... 61

Detailed NetLinx (Link/Act and Status) LED Behavior.............................................................................. 62

DXLink TX/RX in a Multiple-Stage Switching System...............................................................................63

Network Configuration.....................................................................................................64

Overview ................................................................................................................................................. 64

Factory Default Parameters ..................................................................................................................... 66

Device IDs................................................................................................................................................ 67

Using the ID Pushbutton.......................................................................................................................... 67

Contents

4

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

IRL File Transfers ..............................................................................................................72

Overview ................................................................................................................................................. 72

Preparing for IRL File Transfers in an Endpoint System ........................................................................... 73

Preparing for IRL File Transfers in an Extender System ........................................................................... 74

Transferring IRL Files ............................................................................................................................... 75

NetLinx Programming of DXLink Transmitters and Receivers ..........................................78

Overview ................................................................................................................................................. 78

Device Numbering and Ports................................................................................................................... 78

CHANNELs ............................................................................................................................................. 80

DXLink Receiver Video SEND_COMMANDs............................................................................................ 80

DXLink Receiver Audio SEND_COMMANDs............................................................................................ 82

DXLink Transmitter Video SEND_COMMANDs ....................................................................................... 83

DXLink Transmitter Audio SEND_COMMANDs ....................................................................................... 87

IR SEND_COMMANDs............................................................................................................................. 88

Serial SEND_COMMANDs ....................................................................................................................... 92

DXLink Transmitter USB SEND_COMMANDs.......................................................................................... 94

DXLink Receiver USB SEND_COMMANDs...............................................................................................94

Common DXLink Transmitter / Receiver SEND_COMMANDs ................................................................. 95

DXLink System SEND_COMMANDs ........................................................................................................ 96

SEND_STRING Escape Sequences ........................................................................................................... 97

Enova DVX Switchers – DXLink SEND_COMMANDs ............................................................................... 98

Troubleshooting ..............................................................................................................99

Overview ................................................................................................................................................. 99

Basic Troubleshooting ............................................................................................................................. 99

Determining HDCP Compliance............................................................................................................... 99

Power Issues .......................................................................................................................................... 100

DXLink Connection Issues...................................................................................................................... 101

Network Setup Issues ............................................................................................................................ 102

Technical Support .................................................................................................................................. 102

Appendix A – Upgrading the Firmware..........................................................................103

Overview ............................................................................................................................................... 103

Preparing for KIT File Transfers in an Endpoint System......................................................................... 104

Preparing for KIT File Transfers in an Extender System......................................................................... 104

Important Upgrade Information ............................................................................................................ 105

Transferring KIT Files............................................................................................................................. 107

Appendix B – Telnet (Terminal) Commands....................................................................108

Establishing a Terminal Connection Via Telnet ...................................................................................... 108

Telnet Username and Password............................................................................................................. 109

Telnet Commands.................................................................................................................................. 110

Master Connection Modes..................................................................................................................... 116

Notes on Specific Telnet Clients ............................................................................................................ 117

Contents

5

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Appendix C – Virtual NetLinx Master .............................................................................118

Overview Virtual NetLinx Master (Masterless)....................................................................................... 118

Setting PC to Static IP Address ............................................................................................................. 118

Creating a Virtual Master....................................................................................................................... 120

Preparing a DXLink Unit to Work with a Virtual Master ........................................................................ 121

Appendix D – Cable Details and Pinout Info...................................................................123

Overview ............................................................................................................................................... 123

HDMI Connector Cable Pinout............................................................................................................... 123

HD-15 Connector Cable Pinout.............................................................................................................. 124

DVI Pinout for DVI-to-HDMI Cable Adapter .......................................................................................... 125

Appendix E – Supported Input Resolutions ....................................................................126

Available Pixel Display and Refresh Rate............................................................................................... 126

Appendix F – Supported Output Resolutions.................................................................129

HDMI and DVI Supported Output Resolutions ...................................................................................... 129

Digital Video Output Resolution Support.............................................................................................. 130

Appendix G – Ground Wire Attachment.........................................................................134

Attaching a Ground Wire to a Common Earthed Ground...................................................................... 134

Attaching a Ground Wire to Module without Designated Ground ........................................................ 134

Appendix H – EDID Programming ..................................................................................136

DGX Configuration Software Overview................................................................................................. 136

Software Installation on PC.................................................................................................................... 136

DXLink Connection to PC ...................................................................................................................... 137

EDID Programmer View......................................................................................................................... 138

ESD Warning

6

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

ESD Warning

To avoid ESD (Electrostatic Discharge) damage to sensitive components, make sure you are properly grounded

before touching any internal materials.

When working with any equipment manufactured with electronic devices, proper ESD grounding procedures must

be followed to make sure people, products, and tools are as free of static charges as possible. Grounding straps,

conductive smocks, and conductive work mats are specifically designed for this purpose.

Anyone performing field maintenance on AMX DXLink equipment should use an appropriate ESD field service

kit complete with at least a dissipative work mat with a ground cord and a UL listed adjustable wrist strap with

another ground cord. These items should not be manufactured locally, since they are generally composed of highly

resistive conductive materials to safely drain static charges, without increasing an electrocution risk in the event of

an accident. ESD protective equipment can be obtained from 3M™, Desco

®

, Richmond Technology

®

, Plastic

Systems

®

, and other such vendors.

Important Safety Information and Instructions

7

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Important Safety Information and Instructions

When using and installing your AMX product, adhere to the following basic safety precautions. For more

information about operating, installing, or servicing your AMX product, see your product documentation.

Read and understand all instructions before using and installing AMX products.

Use the correct voltage range for your AMX product.

There are no user serviceable parts inside an AMX product; service should only be done by qualified

personnel.

If you see smoke or smell a strange odor coming from your AMX product, turn it off immediately and

call technical support.

For products with multiple power supplies in each unit, make sure all power supplies are turned on

simultaneously.

Use surge protectors and/or AC line conditioners when powering AMX products.

Only use a fuse(s) with the correct fuse rating in your enclosure.

Make sure the power outlet is close to the product and easily accessible.

Make sure the product is on or attached to a stable surface.

Turn off equipment before linking pieces together, unless otherwise specified in that product’s

documentation.

For safety and signal integrity, use a grounded external power source and a grounded power connector.

To avoid shock or potential ESD (Electrostatic Discharge) damage to equipment, make sure you are

properly grounded before touching components inside an AMX product.

Information et directives de sécurité importantes

8

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Information et directives de sécurité importantes

Veuillez vous conformer aux directives de sécurité ci-dessous lorsque vous installez et utilisez votre appareil

AMX. Pour de plus amples renseignements au sujet de l’installation, du fonctionnement ou de la réparation de

votre appareil AMX, veuillez consulter la documentation accompagnant l’appareil.

Lisez attentivement toutes les directives avant d’installer et d’utiliser les appareils AMX.

Le voltage doit être approprié à l’appareil AMX.

Les appareils AMX ne contiennent aucune pièce réparable par l’usager; la réparation ne doit être

effectuée que par du personnel qualifié.

Si de la fumée ou une odeur étrange se dégagent d’un appareil AMX, fermez-le immédiatement et

appelez le Service de soutien technique.

Veillez à ce que tous les blocs d’alimentation des appareils dotés de blocs d’alimentation multiples dans

chaque unité soient allumés simultanément.

Servez-vous de protecteurs de surtension ou de conditionneurs de lignes à courant alternatif lorsque

vous mettez les appareils AMX sous tension.

Placez uniquement des fusibles de calibre exact dans les boîtiers.

Veillez à ce que la prise de courant soit proche de l’appareil et facile d’accès.

Veillez à ce que votre appareil AMX soit installé sur une surface stable ou qu’il y soit fermement

maintenu.

Fermez toutes les composantes de l’équipement avant de relier des pièces, à moins d’indication

contraire fournie dans la documentation de l’appareil.

Par mesure de sécurité et pour la qualité des signaux, servez-vous d’une source d’alimentation externe

mise à la terre et d’un connect d’alimentation mis à la terre.

Pour éviter les chocs ou les dommages éventuels causés à l’équipement par une décharge

électrostatique, veillez à ce le dispositif oit bien relié à la terre avant de toucher les composantes se

trouvant à l’intérieur d’un appareil AMX.

Notices

9

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Notices

Copyright Notice

AMX

©

system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or

otherwise, without the prior written permission of AMX. Copyright protection claimed extends to AMX hardware

and software and includes all forms and matters copyrightable material and information now allowed by statutory

or judicial law or herein after granted, including without limitation, material generated from the software

programs which are displayed on the screen such as icons, screen display looks, etc. Reproduction or disassembly

of embodied computer programs or algorithms is expressly prohibited.

No patent liability is assumed with respect to the use of information contained herein.

Liability Notice

While every precaution has been taken in the preparation of this publication, AMX assumes no responsibility for

error or omissions. No liability is assumed for damages resulting from the use of the information contained herein.

Further, this publication and features described herein are subject to change without notice.

US FCC Notice

The United States Federal Communications Commission (in 47 e-CFR 15.105) has specified that the following

notice be brought to the attention of the users of this product.

“Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.”

Lithium Batteries Notice

Switzerland requires the following notice for products equipped with lithium batteries. This notice is not

applicable for all AMX equipment.

Upon shipment of the products to Switzerland, the requirements of the most up-to-date Swiss Ordinance Annex

2.15 of SR 814.81 will be met including provision of the necessary markings, documents, and annual reports

relative to the disposal of the batteries to the Swiss Authorities.

Trademark Notices

AMX

®

, Enova

®

, AutoPatch

®

, NetLinx

®

, DXLink

™

, SmartScale

®

, and InstaGate Pro

®

are trademarks of AMX.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

UL

®

and the UL logo are trademarks of UL LLC.

3M

™

, Desco

®

, Richmond Technology

®

, and Plastic Systems

®

are registered trademarks.

Ethernet

®

is a registered trademark of the Xerox Corporation.

ENERGY STAR

®

is a registered trademark of the U.S. Department of Energy and the U.S. Environmental

Protection Agency.

Other products mentioned herein may be the trademarks of their respective owners.

Notices

10

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Warnings and Cautions

This manual uses the following conventions and icons to draw attention to actions or conditions that could

potentially cause problems with equipment or lead to personal risk.

ESD Warning: The icon to the left indicates text regarding potential danger associated with the discharge of

static electricity from an outside source (such as human hands) into an integrated circuit, often resulting in

damage to the circuit.

Warning: The icon to the left indicates text that warns readers against actions or conditions that could cause

potential injury to themselves.

Caution: The icon to the left indicates text that cautions readers against actions that could cause potential

injury to the product or the possibility of serious inconvenience.

Product Overview and Specifications

11

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Product Overview and Specifications

Applicability Notice

The information in this manual applies to the DXLink Multi-Format Transmitter Module, the DXLink HDMI

Transmitter Module, the DXLink Multi-Format Wallplate Transmitter, the DXLink Multi-Format Decor Style

Wallplate Transmitter (US), and the DXLink HDMI Receiver Module listed in the table below. In this manual,

these products will be referred to as the Multi-Format TX, HDMI TX, Wallplate TX, Decor Wallplate TX, and

the HDMI RX. When referring to all four of the transmitter units, the term Transmitters will be used.

DXLink™ Twisted Pair Transmitters and Receiver

* The DXLink HDMI TX Module has been discontinued. This manual contains information on it for support.

Compatibility Note: The Transmitters and the Receiver listed above are compatible with a number of other

DXLink products (see the section “Product Compatibility Tables” on page 12). All of the Transmitters are

compatible with the Receiver. The Wallplate TX and Decor Wallplate TX must

use DXLink power injectors

when connecting directly to an HDMI RX; others may cause damage.

Product Notes

The Transmitters and Receiver are designed for transmission of an HDMI signal over twisted pair cable (or a DVI

signal via a DVI-to-HDMI cable adapter) up to 328 feet (100 m). Functionality is briefly described below.

Multi-Format TX – The Multi-Format TX receives an HDMI signal or analog video signal (composite, Y/C,

Y/Pb/Pr, RGB, RGBS, or RGBHV) and an audio signal from a source device. The audio can be either digital

audio embedded with the HDMI signal, digital audio over S/PDIF, or analog stereo audio.

Either analog or digital video is transmitted out of the DXLink output. The active video selection is made using

one of two methods: 1) Automatic, which selects digital video as the priority video input or analog video when no

digital video is present. 2) Active ICSP command video input selection from a bound NetLinx Central Controller.

Both the video and audio are transported over twisted pair cable to an Enova DGX Digital Media Switcher, an

applicable Enova DVX Solution (to an HDMI RX), or directly to an HDMI RX.

The 232 port (RS-232) on the Multi-Format TX supports bidirectional serial data via the twisted pair cable to/from

the 232 port on an HDMI RX. The Multi-Format TX also has IR ports.

HDMI TX

– The HDMI TX receives an HDMI signal and an audio signal from a source device. The audio can be

either digital audio embedded with the HDMI, digital audio over S/PDIF, or analog stereo audio. Both the video

and audio are transported over twisted pair cable to an Enova DGX Digital Media Switcher, an applicable Enova

DVX Solution (to an HDMI RX), or directly to an HDMI RX. The 232 port (RS-232) on the HDMI TX supports

bidirectional serial data via the twisted pair cable to/from the 232 port on an HDMI RX. The HDMI TX also has

IR ports.

Wallplate TX and Decor Wallplate TX – These wallplates receive an HDMI signal or analog video signal

(composite, Y/C, Y/Pb/Pr, RGB, RGBS, or RGBHV) and an audio signal from a source device. The audio can be

either digital audio embedded with the HDMI signal or analog stereo audio.

Either analog or digital video is transmitted out of the DXLink output. The active video selection is made using

one of two methods: 1) Automatic, which selects digital video as the priority video input or analog video when no

digital video is present. 2) Active ICSP command video input selection from a bound NetLinx Central Controller.

FG # Model Model Number, Description

FG1010-310 Multi-Format TX AVB-TX-MULTI-DXLINK, DXLINK MULTIFORMAT HDCP TX

FG1010-300 HDMI-TX* AVB-TX-HDMI-DXLINK, DXLINK HDMI HDCP TX

FG1010-320-BL

FG1010-320-WH

Multi-Format

Wallplate TX

AVB-WP-TX-MULTI-DXLINK, DXLINK MUTIFORMAT

WALLPLATE TX (BLACK or WHITE)

FG1010-325-BL

FG1010-325-WH

Multi-Format Decor

Style Wallplate TX

AVB-DWP-TX-MULTI-DXLINK, DXLINK MULTI DECOR HDCP TX

(BLACK or WHITE)

FG1010-500 HDMI-RX AVB-RX-DXLINK-HDMI, DXLINK HDMI HDCP RX W SCALER

Product Overview and Specifications

12

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Both the video and audio are transported over twisted pair cable to an Enova DGX Digital Media Switcher, an

applicable Enova DVX Solution, or directly to an HDMI RX. Direct connection requires either PDXL-2

(FG1090-170) or PS-POE-AT-TC (FG423-84).

HDMI RX

– The HDMI RX receives an HDMI signal with embedded audio over twisted pair cable from a

DXLink compatible device (or from a DXLink Transmitter) and sends the signal on to the destination. Audio

received on the HDMI RX can also be output on the Stereo Audio Out port if it originated as a 2 channel audio

signal. The 232 port (RS-232) on the HDMI RX supports bidirectional serial data via the twisted pair cable

to/from the 232 port on the Multi-Format TX or HDMI TX. The HDMI RX features SmartScale

®

Technology

(integrated EDID output scaling) to ensure an appropriate output resolution, plus it supports a Manual (override)

option for setting up custom resolutions and a Bypass option. The HDMI RX also has IR ports.

Note: If a DVI-D signal is used (via a DVI-to-HDMI cable adapter), the advanced audio support from HDMI

will not be available.

Note: These DXLink products support several different modes which are available for system setup and use.

Brief explanations of the modes are provided in the section “Quick Reference Tables for Modes” on page 28

along with page references to complete information.

Product Compatibility Tables

The Transmitters and the Receiver are compatible with the DXLink products listed in the two tables below.

Enova DGX Solutions and DXLink Functions

The following table shows which Enova DGX products support specific DXLink functions.

* Inputs and outputs up to 8, 16, or 32 depending on the system (in increments of 4 inputs or outputs per board).

** For power budget information for system planning when using DXLink Transmitters and Receivers with an

Enova DGX Digital Media Switcher, see page 41.

Enova DVX Solutions and DXLink Functions

The following table shows which Enova DVX products support specific DXLink functions.

* Does not apply to the DVX-2100HD.

DXLink Functions in Enova DGX Solutions

DXLink Twisted Pair Input Boards DXLink Twisted Pair Output Boards

DXLink Inputs Up to 8/16/32* –

Power on DXLink Inputs** Yes –

DXLink Outputs – Up to 8/16/32*

Power on DXLink Outputs** –Yes

DXLink Functions in Enova DVX Solutions*

DVX-3156HD DVX-3155HD DVX-3150HD DVX-2155HD DVX-2150HD

DXLink Inputs 42020

Power on DXLink Inputs Yes Yes NA Yes NA

DXLink Outputs 22211

Power on DXLink Outputs No No No Yes Yes

Product Overview and Specifications

13

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

DXLink Transmitter and Receiver Features

Note: The Wallplate TX and Decor Wallplate TX have a limited set of features (i.e., no S/PDIF, IR, or serial

ports).

Incorporates HDMI

®

technology

HDCP 1.3 compatible

Supports computer video up to 1920x1200, HDTV up to 1080p, as well as 3D support (3D and Deep Color)

Supports HDMI pass through with embedded digital audio and single link DVI (DVI-to-HDMI cable adapter

required)

Multi-Format TX, Wallplate TX, and Decor Wallplate TX support analog video: composite, Y/C, Y/Pb/Pr,

RGB, RGBS, or RGBHV

Reads the downstream EDID from the switcher (Endpoint Mode) or the sink (Extender Mode)

Transports video signals over distances up to 328 feet (100 m) via the DXLink connection

Interruption free content when used in conjunction with a switcher, AMX’s exclusive InstaGate Pro

®

Technology allows audio and video to be switched quickly and easily to every connected display without the

difficulties typically associated with HDCP.

AutoDetect on the TXs and SmartScale

®

on the RX work to automatically recognize any device’s supported

resolutions and signal type parameters, allowing switching out source and destination devices without

manual setup. Also included is the ability to control detailed timing parameters for customized video output

formats. (SmartScale is the ability to configure the scaling output by automatically selecting destination

defined resolutions.)

Supports HDMI embedded digital audio, digital audio over S/PDIF, and analog stereo audio

Standard twisted pair cable saves time and installation effort

The USB port on the HDMI Receiver passes keyboard and mouse USB signals to control a remote computer.

The Transmitter’s USB port connects to a Host PC and will forward HID keyboard and mouse data received

from a directed Receiver’s USB port. (For USB port information, see page 26.)

The 232 port (RS-232 serial) supports bidirectional transfer of serial data between Master and TX or RX

(Endpoint Mode) or between TX and RX (Extender Mode)

The IR port supports bidirectional transfer of IR data between Master and TX or RX (Endpoint Mode) or

between TX and RX (Extender Mode)

Power over DXLink (twisted pair cable) support when used with a switcher or with an approved AMX Power

over DXLink device (for power budget information when used with an Enova DGX Digital Media Switcher,

see page 41)

A desktop power supply (ENERGY STAR

®

qualified) is provided per module. The Wallplate TX and

Decor Wallplate TX receive power from the switcher or can be used with a DXLink power injector

(for power budget information, see page 41).

The modules are compatible with all V Style, versatile mounting options including rack, surface, and pole.

The Wallplate TX includes a mounting bracket, and the Decor Wallplate TX mounts in a standard

US double-gang box.

Backed by AMX’s 3 year warranty (see www.amx.com)

24-hour technical support

Note: Features and specifications described in this document are subject to change without notice.

Product Overview and Specifications

14

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Common Applications

DXLink Transmitters and Receivers are designed to send audio, video, and control to a remote display across the

room, on the other side of the house, or to a classroom down the hall. The installation’s requirements dictate the

system setup which generally takes one of the following three forms.

Endpoint Mode (Switcher) – One or more Transmitters and/or Receivers are connected to a switcher*

containing an integrated Master (see page 38).

Endpoint Mode (Standalone) – A standalone DXLink TX/RX pair** are connected directly to each other

but, in addition, either the TX or RX is connected to a NetLinx Central Controller via a LAN or directly to the

Controller (see page 40).

Extender Mode (Standalone) – A standalone DXLink TX/RX pair** are connected directly to each other as

a simple extender solution (see page 41).

* The switcher can be either an Enova DGX Switcher or an applicable Enova DVX Solution (see page 12).

** A wallplate in a standalone configuration requires power via a DXLink power injector.

Transmitters

Note: If a DVI-D signal is used (via a DVI-to-HDMI cable adapter), the advanced audio support from HDMI

will not be available.

DXLink Multi-Format TX (AVB-TX-MULTI-DXLINK) Front View

DXLink HDMI TX (AVB-TX-HDMI-DXLINK) Front View (product discontinued)

FIG. 1 Multi-Format TX front view

FIG. 2 HDMI TX front view

Digital Video and Audio LEDs

Power LED

CEC LED

IR LEDs

232 (serial) LEDs

NetLinx LEDs USB LED

ID Pushbutton

Analog Video LEDs

Program port

Digital Video and Audio LEDs

Power LED

CEC LED

IR LEDs

232 (serial) LEDs

NetLinx LEDs USB LED

ID Pushbutton

Program port

Product Overview and Specifications

15

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Components located on front of Multi-Format TX and HDMI TX (left to right):

Power LED – Indicates when the Multi-Format TX or HDMI TX is powered on.

Digital Video and Audio LEDs – Indicate the presence of digital video and digital audio signals, including an

embedded audio signal on the HDMI path.

Analog Video LEDs (Multi-Format TX only) – Indicate the type of analog video present through the

Multi-Format TX: composite or Y/C; Y/Pb/Pr or RGB; RGBHV or RGBS.

Program port – This port (USB mini-B connector) supports DGX Configuration Software for programming

a customer VGA EDID.

IR LEDs – TX and RX LEDs indicate active IR communication.

232 LEDs (RS-232 serial) – TX and RX LEDs indicate active serial communication.

NetLinx LEDs – Link/Act LED indicates network communication activity. The Status LED indicates unit

status.

CEC LED – CEC is not currently supported.

USB LED – When illuminated, the LED indicates that the USB port is connected and enabled (for details,

see page 27).

ID Pushbutton – Places the Multi-Format TX or HDMI TX in ID Mode for setting the NetLinx ID (device

only) and provides additional functionality, such as placing the device in Static IP Mode or DHCP Mode.

Multi-Format TX and HDMI TX LEDs

Note: For detailed behavior of the NetLinx Link/Act and Status LEDs on the module’s front, see page 62.

For detailed behavior of the RJ-45 connector LEDs on the module’s rear, see page 50.

Multi-Format TX and HDMI TX Indicator LEDs

LED Normal Display Indicates

Power Green Power is applied to the Transmitter Module

Digital Video Green A digital video signal is present through the Transmitter Module

Audio Green Embedded audio signal is present through the Transmitter Module

Analog Video

(Multi-Format TX only)

One of the 3 LEDs

will be Green

The type of analog video present through the Multi-Format TX:

• C (composite) or Y/C (two component)

• Y/PB/PR or RGB (three component)

• RGBHV (five component) or RGBS (four component)

IR TX Red IR TX active communication

IR RX Yellow IR RX active communication

232 (Serial) TX Red Serial TX active communication

232 (Serial) RX Yellow Serial RX active communication

NetLinx Link/Act Green Active LAN connection to an AMX Network (Blinking = #3 Toggle OFF)

NetLinx Status Green LAN connection is active

CEC OFF CEC is not currently supported

USB Yellow USB port is connected and enabled (for details, see page 27)

Product Overview and Specifications

16

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

DXLink Multi-Format Wallplate TX (AVB-WP-TX-MULTI-DXLINK) Front View

Components located on front of Wallplate TX:

HDMI In – HDMI connector (with locking center screw) for digital video and embedded digital audio

(supports a DVI-D signal with use of DVI-to-HDMI cable adapter). When more than one audio signal is

present, HDMI embedded audio takes precedence over analog audio.

Digital Video LED – Indicates the unit is configured to pass HDMI with embedded audio (default).

Video In – An HD-15 connector for analog video: C (composite), Y/C, Y/Pb/Pr, RGB, RGBHV, or RGBS.

Pinouts for analog video are on page 124.

Analog Video LEDs – Illuminates when the Wallplate TX is configured to pass analog video: composite or

Y/C; Y/Pb/Pr or RGB; RGBHV or RGBS.

Audio In Stereo – Audio connector is a 3.5 mm stereo jack. An analog audio signal is only available when

HDMI embedded digital audio is not present (or configured for analog audio).

Audio LED – Indicates the unit is configured to pass analog audio (coupled with digital or analog video

path).

USB Host port – Mini-B USB connector (supports USB host) for receiving keyboard / mouse commands

from a specific RX. (For USB port information, see page 26.)

Power LED – Indicates when the Wallplate TX is powered on.

Components located on left and bottom edges of Wallplate TX:

Reset button (left) – Resets the Wallplate TX’s CPU (acts like a power cycle soft reboot).

Program port (left) – This port (USB mini-B connector) supports DGX Configuration Software for

programming a customer VGA EDID.

ID Pushbutton (left) – Places the Wallplate TX in ID Mode for setting the NetLinx ID (device only) and

provides additional functionality, such as placing the device in Static IP Mode or DHCP Mode.

NetLinx LEDs (bottom) – Left green LED (L = Link/Act) indicates network communication activity; right

green LED (S = Status) indicates unit status

.

DXLink LEDs (bottom) – Left yellow LED indicates HDCP status; right green LED indicates that a valid

DXLink connection has been established.

FIG. 3 Multi-Format Wallplate TX front view, plus left edge and bottom edge views

Left edge

Reset button

Program port

ID Pushbutton

Analog Video LEDs

HD-15 Input

Digital Video LED

Audio LED

HDMI Input

USB Host

Stereo Audio Input

Power LED

DXLink LEDs

Bottom edge

NetLinx LEDs

Product Overview and Specifications

17

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

DXLink Decor Wallplate TX (AVB-DWP-TX-MULTI-DXLINK) Front View

Important: Be sure to measure the back box and any other components used to mount the Decor Wallplate

TX prior to installation/construction to ensure the unit fits (e.g., some mud rings do not work unless their

corners are modified).

Components located on left and right front sections of Decor Wallplate TX:

USB Host port – Mini-AB USB connector (supports USB host) for receiving keyboard / mouse commands

from a specific RX. (For USB port information, see page 26.)

Audio In Stereo – Audio connector is a 3.5 mm stereo jack. An analog audio signal is only available when

HDMI embedded digital audio is not present (or configured for analog audio).

Video In – An HD-15 connector for analog video: C (composite), Y/C, Y/Pb/Pr, RGB, RGBHV, or RGBS.

Pinouts for analog video are on page 124.

HDMI In – HDMI connector (with locking center screw) for digital video and embedded digital audio

(supports a DVI-D signal with use of DVI-to-HDMI cable adapter). When more than one audio signal is

present, HDMI embedded audio takes precedence over analog audio.

Power LED – Indicates when the Decor Wallplate TX is powered on.

Audio LED – Indicates the unit is configured to pass analog audio (coupled with digital or analog video

path).

Analog Video LEDs – Illuminates when the Decor Wallplate TX is configured to pass analog video:

composite or Y/C; Y/Pb/Pr or RGB; RGBHV or RGBS.

Digital Video LED – Illuminates when the Decor Wallplate TX is configured to pass HDMI with embedded

audio (default).

The Decor Wallplate TX has a number of front panel components, some can been seen when a standard decor

style front cover plate is attached and some are hidden by the plate (FIG. 4 shows all of them). The cover plate is

customer provided to allow matching the individual decor of an environment or matching other standard decor

covers in a room/area.

Components located on center front section of Decor Wallplate TX:

USB Program port – This port (USB mini-B connector) supports DGX Configuration Software for

programming a customer VGA EDID.

Reset button – Resets Decor Wallplate TX’s CPU (acts like power cycle soft reboot).

Dip switch – A four-toggle DIP switch is used for enabling/disabling special functionality (see page 43).

ID Pushbutton – Places the Decor Wallplate TX in ID Mode for setting the NetLinx ID (device only) and

provides additional functionality, such as placing the device in Static IP Mode or DHCP Mode.

DXLink LEDs – HDCP LED indicates HDCP status; DXLink LED indicates that a valid DXLink connection

has been established.

NetLinx LEDs – Status LED indicates unit status; Link/Act LED indicates network communication activity.

FIG. 4 Decor Wallplate TX front view (before customer provided standard decor style front cover plate is attached)

Analog Video LEDs

HD-15 Input

Digital Video LED

Audio LED

HDMI Input

USB Host

Stereo Audio Input

Power LED

Reset button

Program port

ID Pushbutton

DXLink LEDs

DIP switch

NetLinx LEDs

Cover plate screw hole

Back box screw hole

Product Overview and Specifications

18

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

Wallplate TX and Decor Wallplate TX Front LEDs

* The LEDs for Digital Video, Analog Video, and Audio each indicate the configured state of the connectors, not

necessarily the presence of signals through the Wallplate TX and Decor Wallplate TX.

Note: Detailed behavior for the NetLinx-L and NetLinx-S LEDs on the Wallplate TX or Link/Act and Status

LEDs on the Decor Wallplate TX are on page 62, and basic information for the LEDs on the RJ-45 connector

on the rear of the Wallplate TX and Decor Wallplate TX is on page 50.

Tip: If the Wallplate TX is installed in a location where it is difficult to check the LEDs on the bottom edge,

slide a white piece of paper or a small mirror under the edge to view LED status.

Multi-Format TX Rear View

Wallplate TX and Decor Wallplate TX Indicator LEDs

LEDs Normal Display Indicates

Digital Video

(default)

Green The Wallplate TX and Decor Wallplate TX have been configured* to pass

HDMI (for SEND_COMMAND information, see page 85)

Analog Video One of the 3 LEDs

will be Green

The Wallplate TX and Decor Wallplate TX have been configured* to pass

one of the following types of analog video (for SEND_COMMAND

information, see page 85):

• C (composite) or Y/C (two component)

• Y/PB/PR or RGB (three component)

• RGBHV (five component) or RGBS (four component)

Audio Green The Wallplate TX and Decor Wallplate TX have been configured* to pass

analog audio as the audio source being embedded on the DXLink output

connection (coupled with either the analog or digital video input path); for

SEND_COMMAND information, see page 87

Power Green Power (from switcher) is applied to the unit

LEDs (bottom edge of Wallplate TX)

NetLinx - L (Link) Green Active LAN connection to an AMX Network (Blinking = #3 Toggle OFF)

NetLinx - S (Status) Green

Off

• Speed status is 100 Mbps

• Speed status is 10 Mbps

DXLink Yellow Yellow

Flashing

Off

• Authenticated HDCP (handshaking has occurred successfully)

• Video is active; no HDCP

• No Video

DXLink Green Green DXLink connection is established

LEDs (under customer provided front cover plate on Decor Wallplate TX)

HDCP (DXLink) Yellow

Flashing

Off

• Authenticated HDCP (handshaking has occurred successfully)

• Video is active; no HDCP

• No Video

DXLink Green DXLink connection is established

Status (NetLinx) Green

Off

• Speed status is 100 Mbps

• Speed status is 10 Mbps

Link/Act (NetLinx) Green Active LAN connection to an AMX Network (Blinking = #3 Toggle OFF)

FIG. 5

Multi-Format TX rear view

IR ports

RS-232 port

HDMI In connector Stereo Audio In jack

USB port

ICS LAN 10/100 connector

Power jack

DXLink output connector

Digital Audio In jack

Video In connector

Ground screw

Product Overview and Specifications

19

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

HDMI TX Rear View (product discontinued)

Note: The Multi-Format TX and HDMI TX each have a DIP switch on the bottom (see page 25).

The following components are located on the rear of the Multi-Format TX and HDMI TX Modules (from left to

right):

Video In Connector (Multi-Format TX only)

The Video In connector on the Multi-Format TX is an HD-15 connector for analog video (composite, Y/C,

Y/Pb/Pr, RGB, RGBHV, or RGBS). Pinouts for analog video are on page 124.

Note: When an analog video source cable is plugged into the Multi-Format TX, the Video LEDs on the front

and on the Receiver turn green to show that video is present through the system. In addition, one of the

Analog Video LEDs on the front of the Multi-Format TX and the HDMI RX turns green to show the type of

video that is present through the system.

HDMI In Connector

The HDMI In connector is for digital video and embedded digital audio. When more than one audio signal is

present and the default “auto” mode is enabled, HDMI embedded audio takes precedence over S/PDIF and analog

audio.

When a NetLinx Central Controller is connected, an audio format SEND_COMMAND is available (the

Transmitter must be set for network connectivity via #3 Toggle) to select the desired audio source (see page 87).

The HDMI connector has a center screw for locking capability. The HDMI connector also supports a DVI-D

signal with the use of a DVI-to-HDMI cable adapter.

Note: When a digital video source cable is plugged into the HDMI connector, the Video LEDs on the front of

the Multi-Format TX or HDMI TX and Receiver turn green to show that video is present through the system.

Stereo Audio In Jack

The Stereo Audio In jack is a 3.5 mm stereo jack. By default, the stereo audio jack will be third in priority behind

the embedded audio on the HDMI input and digital audio on the RCA connector.

When a NetLinx Central Controller is connected, an audio format SEND_COMMAND is available (the

Transmitter must be set for network connectivity via #3 Toggle) to select the desired audio source (see page 87).

Digital Audio In Jack

The Digital Audio In jack is an RCA jack for an S/PDIF audio signal. When more than one audio signal is present

and the default “auto” mode is enabled, HDMI embedded audio takes precedence over S/PDIF, which takes

precedence over analog audio.

When a NetLinx Central Controller is connected, an audio format SEND_COMMAND is available (the

Transmitter must be set for network connectivity via #3 Toggle) to select the desired audio source (see page 87).

FIG. 6 HDMI TX rear view

IR ports

RS-232 port

HDMI In connector

Stereo Audio In jack

USB port

ICS LAN 10/100 connector

Power jack

DXLink output connector

Digital Audio In jack

Ground screw

Product Overview and Specifications

20

Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver

ICS LAN10/100 Connector

The ICS LAN 10/100 (RJ-45) connector provides for Ethernet 10/100 connectivity (e.g., receiving

SEND_COMMANDs and downloading firmware update files). For pinout and LED information, see page 50.

RS-232 (Serial) Port

The RS-232 port (serial data interface) is a 3-position screw terminal block which accepts data from the source

device and transfers it via the twisted pair cable to the HDMI RX, which in turn transfers the data to the

destination device. The transfer of data can also be made from the destination to the source. In addition to being

directly connected to a device, this port can be connected as an independent native NetLinx control port from a

networked NetLinx Central Controller.

IR RX Port

The IR RX port is used for IR control (see page 27). This port is a 3.5 mm stereo jack. In addition to being directly

connected to a device, this port can be connected as an independent native NetLinx control port from a networked

NetLinx Central Controller.

IR TX Port

The IR TX port is used for IR control (see page 27). This port is a 2-way mini-Phoenix connector. In addition to

being directly connected to a device, this port can be connected as an independent native NetLinx control port

from a networked NetLinx Central Controller.

USB Port

The USB-B port on the rear of the Multi-Format TX and HDMI TX is connected to a PC and supports a USB

device. This is the Host port that is used in conjunction with the USB-A port on the rear of the HDMI RX for

sending keyboard / mouse commands to a connected PC at the Transmitter. (For USB port information, see

page 26.)

DXLink Output Connector

The DXLink (RJ-45) connectors transport digital video, embedded audio, Ethernet, and bidirectional control over

twisted pair cable to DXLink devices or boards (or an HDMI RX), including digitally transcoded analog video

signals. The DXLink path supports HDCP. The DXLink line also supports power from an Enova DGX Switcher

and from some Enova DVX Solutions to power the module. For pinout and LED information, see page 50.

Ground Screw

The ground screw is used for creating a technical ground for the ungrounded sources/destinations with respect to

the DXLink Transmitters/Receivers and switcher (see page 47).

Power Jack

Important: If desktop power is used to power the Transmitter, only the provided desktop power supply should

be used and it must not

be altered in any way. Remote power can also be provided via a switcher, PDXL-2

(FG1090-170), or PS-POE-AT-TC (FG423-84).

The power receptacle is a 2.1 mm DC jack for connecting power. Power can come from a locally connected DC

supply of 12 V. The automatically adjusting universal 110/220 IEC power supply is provided. The power supply is

ENERGY STAR

®

qualified to ensure maximum efficiency and savings.

Note: Transmitter Modules can also be powered via the DXLink connector when attached to a DXLink Input

Board in an Enova DGX Switcher. We recommend calculating the power budget for the switcher to maintain

the redundancy of its power supplies (see page 41).

Page is loading ...

AMX DXLink User manual

AMX DXLink User manual

Related papers

Other documents