George Kovacs P1171-077-L User manual

Brand: George Kovacs

Model: P1171-077-L

Type: User manual

George Kovacs P1171-077-L is an LED wall mount fixture which can replace your old fixture easily following the provided instructions. It comes with adjustable brightness, which can be set using C-L(CFL & LED) or Incandescent/Halogen type dimmers. Make sure to turn off the power at the fuse or circuit breaker box before starting the installation. You can replace the LED module yourself if you are a qualified electrician. If not, please contact a specified supplier.

George Kovacs P1171-077-L is an LED wall mount fixture which can replace your old fixture easily following the provided instructions. It comes with adjustable brightness, which can be set using C-L(CFL & LED) or Incandescent/Halogen type dimmers. Make sure to turn off the power at the fuse or circuit breaker box before starting the installation. You can replace the LED module yourself if you are a qualified electrician. If not, please contact a specified supplier.

INSTALLATION INSTRUCTIONS FOR P1171-077-L

For LED wall mount Fixture

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R .

Fig.1F

Fig. 2

Fig.3

IMPORTANT

:

Fixture should be installed by a

qualified electrician to ensure proper wiring and

installation.

Dimmable with C-L (CFL & LED)type and

Incandescent/Halogen type dimmers

PREPARATION

1. Shut off power at the fuse box or circuit breaker box. If

necessary remove the old fixture and mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts

on a clear area. Take care not to lose any small parts

necessary for installation.

ASSEMBLING THE FIXTURE (Fig.1)

3. Attach the mounting plate (A) to the junction box with

junction box screw (B) (Size: 8-32*1/2’’L). The side of the

mounting plate marked “GND” must face out.

CONNECTION THE WIRES (Fig. 2)

4. Connect the electrical wires as shown in Fig.2, making

sure that all wire nuts are secured. If your outlet has a

ground wire (green or bare copper), connect the fixture's

ground Wire to it. Otherwise, connect the fixture's ground

wire directly to the circular strap using the green screw

provided. Tuck the wire connections neatly into the junction

box.

FINISHING THE INSTALLATION (Fig. 1)

5. Align Fixture (E) to mounting plate (A) and secure with

screws (D).

Your installation is now complete. Return power to the junction

box and test the fixture.

CAUTION /ATTENTION:

When handling the fixture, do not

apply pressure to the LEDs. Hold the fixture by the base or

fixture body (E) only.

Replacing LED module (Fig.3)

The LED module can be replaced by a qualified electrician without

cutting of wire and without damage to any decorative element to

which the fixture is attached. See installation steps for more details

(Fig 3.)

Warning: Turn off power at the circuit breaker before

replacing LED module.

a. Loosen screws (D), remove the wire nuts and place the fixture

on a clear flat surface.

a. Loosen screws (G) and remove end caps (H), acrylic shade (L)

and glass plate (K).

b. Loosen screws (J), screws (M), wire fastener (N). And then

remove LED module (I) carefully.

c. Reverse steps a-c for installing the new LED module.

Note: The LED module should be provided by a specified supplier.

1

George Kovacs P1171-077-L User manual

Brand: George Kovacs

Model: P1171-077-L

Type: User manual

George Kovacs P1171-077-L is an LED wall mount fixture which can replace your old fixture easily following the provided instructions. It comes with adjustable brightness, which can be set using C-L(CFL & LED) or Incandescent/Halogen type dimmers. Make sure to turn off the power at the fuse or circuit breaker box before starting the installation. You can replace the LED module yourself if you are a qualified electrician. If not, please contact a specified supplier.

Download PDF

Related papers

Other documents