2. Miele
  3. KWT 1601 Vi

Miele KWT 1601 Vi, 36160111USA Specification

  • Hello! I am an AI chatbot trained to assist you with the Miele KWT 1601 Vi Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 011208
Product and Cut-out Dimensions
KWT1611Vi / KWT1601Vi
24"
25" min.
23 3/4"
83 1/2" - 85 3/8"
9 1/2"
24"
2" - 8 3/8"
4 1/8"
84"
1 1/4"
E
UNIT ACCEPTS
A CUSTOM
FRONT FRAME
6 5/8" - 8 1/2"
O
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear.
Standard NEMA 5-15 Outlet - locate less than 9" above
finished floor
E -
O -
• All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame) to
insure proper fit and finish
Location Codes
NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 011208
Product and Cut-out Dimensions
KWT1611Vi / KWT1601Vi
Glass dimensions
44 1/2"
Hinge
Hinge
1/2" - 2 3/8"
Centerline
19"
65"
Notes
• Centerpoint is 45 1/2" with typical 84" installation
NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 011208
Front Panel Information
Fully Integrated Model
Width: 23 3/4" in all cases
Thickness: Minimum 3/4" outside frame
Height: Determined using the following calculation:
Panel Height = HOC - TKH
HOC = Total height of cabinet or side panel
TKH = Toe-kick height
Note: Finish back side of panels to insure appearance
Panel may extend above unit. This is not
considered in height calculation
Maximum hinge capacity: 200 Pounds
Maximum panel weight: 128 Pounds
TKH
HOC
Panel Height
Custom Panel Installations
These units do not come equipped with a front panel. They are designed to accept a custom door panel supplied by
the cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surrounding
cabinets.
Panel size is determined in the following manner:
Panel Notes
If the adjoining cabinets are taller than the height of machine (HOM) - the front panel may be extended accordingly.
Simply maintain the toekick height and extend the panel the needed distance.
Adjoining cabinet
Machine
Extended Panel
2 1/2 - 3 1/4"
Both Sides
5 7/8" Minimum
10 1/8" Minimum
NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 011208
Front Panel Information
Hinging Details
0-1/8"
Front Panel
1"
1-1/4"
1-1/2"
0-3/4"
0-3/4"
1-1/4"
1-1/2"
1-3/4"
2"
1"
Cabinet Front
0-3/4"
1"
1-1/4"
1-1/2"
0-1/8"
F
ro
n
t
P
a
n
e
l
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
90° Door 115° Door
Thickness options Thickness options
Door Swing
NOTE: Additional space needed depending on
thickness of front panels and handle used
26 11/16"
7/16"
Door Swing
11 3/4"
MAX
NOTE: Additional space needed depending on
thickness of front panels and handle used
/