inVue HC15001 User manual

Series 1500

Puck & Stand

HC15000, HC15001, HC15002

2

Read entire instruction guide before starting installation.

System Components

1. Puck/Stand

2. Mounting Plate

3. Recoiler

4. Sensor

5. IR Key (not included)

6. Power connector (if powering up merchandise, order separately)

7. Power Supply (if powering up merchandise, order separately)

Tools

1. T-20 Bit

2. Drill

System Overview

The Series 1500 secures and displays your handheld and

tablet merchandise.

3

5

10

20

30

InVue IR Key

AF4400 or PK4400

Screwdriver & T-20 Bit Drill

Sensor

Puck/Stand

HC15000 - Flat Puck

HC15001 - Angled Stand

HC15002 - Angled Puck

Power Supply

PS18VUS - US

PS18VEU - EU

PS18VAUS - AUS

PS18VUK - UK

PS18VARG - ARG

Power Connector

Recoiler

HC15405

Mounting Plate

HC15406

4

Attaching Puck to Display Counter

Adhesive Mount

(See page 5)

Screw Mount

(See page 7)

5

1

Drill a 19 mm (0.75”) hole in display counter. If

displaying more than one puck/stand: Drill a 19 mm

(0.75”) hole a minimum of 152 mm (6”) apart. Wipe

display counter with alcohol wipe provided. Let it dry

completely.

CONTENTS: One pad saturated in

Isopropyl Alcohol

75%

DIRECTIONS: Apply topically as

needed to cleanse surface mounting area.

FOR EXTERNAL USE ONLY

KEEP OUT OF REACH OF

CHILDREN

KEEP AWAY FROM EYES

AND FIRE

5

10

20

30

6

2

Remove ﬁlm from adhesive. Align puck directly over

hole in display counter and press ﬁrmly for at least 10

seconds. “InVue” on bottom of puck/stand must be

facing back of display counter.

7

Attaching Puck to Display Counter – Screw Mount

8

1

Drill a 19 mm (0.75”) hole in display counter. If display-

ing more than one puck/stand: Drill a 19 mm (0.75”)

hole a minimum of 152 mm (6”) apart.

5

10

20

30

9

2

Cut out template on page 38 to mark drill hole location

for threaded rod. Drill a 7.5 mm (0.3”) hole into display

counter.

FRONT OF STAND

BACK OF STAND

19.00 mm (3/4")

7.50 mm (5/16")

13.80 mm

15.40 mm

10

3

Screw threaded rod into bottom of puck/stand. Remove

ﬁlm from adhesive. Place threaded rod through display

counter and press ﬁrmly for at least 10 seconds. Tighten

wingnut below counter.

11

Attaching Mounting Plate & Recoiler

(Below counter installation)

Adhesive Mount -

Use only if screw mount

cannot be used

(See page 15)

Mounting Plate

Recoiler

Jack

Screw Mount -

Recommended

(See page 12)

12

1

Fit opening in mounting plate to hole in display counter.

Use mounting plate as template to drill all 3 holes for

screws. Tighten all 3 screws with screwdriver.

13

2

Feed jack through hole in mounting plate and push

through puck/stand. Snap recoiler to mounting plate.

Jack will remain locked in puck/stand once pushed

through.

14

3

If powering merchandise: Plug power supply into

mounting plate cord and into outlet.

15

Attaching Mounting Plate & Recoiler – Adhesive Mount

(Use only if screw mount cannot be used)

CONTENTS: One pad saturated in

Isopropyl Alcohol

75%

DIRECTIONS: Apply topically as

needed to cleanse surface mounting area.

FOR EXTERNAL USE ONLY

KEEP OUT OF REACH OF

CHILDREN

KEEP AWAY FROM EYES

AND FIRE

16

1

Remove ﬁlm from adhesive on mounting plate. Fit

opening in mounting plate to hole in display counter.

Press ﬁrmly for at least 10 seconds.

17

2

Feed jack through hole in mounting plate and push

through puck/stand. Snap recoiler to mounting plate.

Jack will remain locked in puck/stand once pushed

through.

18

3

If powering merchandise: Plug power supply into

mounting plate cord and into outlet.

19

Attaching Sensor

Sensor without Bracket Arms

(See page 20)

Sensor with Bracket Arms

(See page 25)

20

1

Wipe back of merchandise with alcohol wipe provided.

Let it dry completely.

CONTENTS: One pad saturated in

Isopropyl Alcohol

75%

DIRECTIONS: Apply topically as

needed to cleanse surface mounting area.

FOR EXTERNAL USE ONLY

KEEP OUT OF REACH OF

CHILDREN

KEEP AWAY FROM EYES

AND FIRE

Page is loading ...

inVue HC15001 User manual

This manual is also suitable for

inVue HC15001 User manual

Related papers

Other documents