2. inVue
  3. 1500 SERIES

inVue 1500 SERIES, HC15000, HC15001, HC15002 User manual

  • Hello! I am an AI chatbot trained to assist you with the inVue 1500 SERIES User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Series 1500
Puck & Stand
HC15000, HC15001, HC15002
2
Read entire instruction guide before starting installation.
System Components
1. Puck/Stand
2. Mounting Plate
3. Recoiler
4. Sensor
5. IR Key (not included)
6. Power connector (if powering up merchandise, order separately)
7. Power Supply (if powering up merchandise, order separately)
Tools
1. T-20 Bit
2. Drill
System Overview
The Series 1500 secures and displays your handheld and
tablet merchandise.
3
5
10
20
30
InVue IR Key
AF4400 or PK4400
Screwdriver & T-20 Bit Drill
Sensor
Puck/Stand
HC15000 - Flat Puck
HC15001 - Angled Stand
HC15002 - Angled Puck
Power Supply
PS18VUS - US
PS18VEU - EU
PS18VAUS - AUS
PS18VUK - UK
PS18VARG - ARG
Power Connector
Recoiler
HC15405
Mounting Plate
HC15406
4
Attaching Puck to Display Counter
Adhesive Mount
(See page 5)
Screw Mount
(See page 7)
5
1
Drill a 19 mm (0.75”) hole in display counter. If
displaying more than one puck/stand: Drill a 19 mm
(0.75”) hole a minimum of 152 mm (6”) apart. Wipe
display counter with alcohol wipe provided. Let it dry
completely.
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
5
10
20
30
6
2
Remove film from adhesive. Align puck directly over
hole in display counter and press firmly for at least 10
seconds. “InVue” on bottom of puck/stand must be
facing back of display counter.
7
Attaching Puck to Display Counter – Screw Mount
8
1
Drill a 19 mm (0.75”) hole in display counter. If display-
ing more than one puck/stand: Drill a 19 mm (0.75”)
hole a minimum of 152 mm (6”) apart.
5
10
20
30
9
2
Cut out template on page 38 to mark drill hole location
for threaded rod. Drill a 7.5 mm (0.3”) hole into display
counter.
FRONT OF STAND
BACK OF STAND
19.00 mm (3/4")
7.50 mm (5/16")
13.80 mm
15.40 mm
10
3
Screw threaded rod into bottom of puck/stand. Remove
film from adhesive. Place threaded rod through display
counter and press firmly for at least 10 seconds. Tighten
wingnut below counter.
11
Attaching Mounting Plate & Recoiler
(Below counter installation)
Adhesive Mount -
Use only if screw mount
cannot be used
(See page 15)
Mounting Plate
Recoiler
Jack
Screw Mount -
Recommended
(See page 12)
12
1
Fit opening in mounting plate to hole in display counter.
Use mounting plate as template to drill all 3 holes for
screws. Tighten all 3 screws with screwdriver.
13
2
Feed jack through hole in mounting plate and push
through puck/stand. Snap recoiler to mounting plate.
Jack will remain locked in puck/stand once pushed
through.
14
3
If powering merchandise: Plug power supply into
mounting plate cord and into outlet.
15
Attaching Mounting Plate & Recoiler – Adhesive Mount
(Use only if screw mount cannot be used)
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
16
1
Remove film from adhesive on mounting plate. Fit
opening in mounting plate to hole in display counter.
Press firmly for at least 10 seconds.
17
2
Feed jack through hole in mounting plate and push
through puck/stand. Snap recoiler to mounting plate.
Jack will remain locked in puck/stand once pushed
through.
18
3
If powering merchandise: Plug power supply into
mounting plate cord and into outlet.
19
Attaching Sensor
Sensor without Bracket Arms
(See page 20)
Sensor with Bracket Arms
(See page 25)
20
1
Wipe back of merchandise with alcohol wipe provided.
Let it dry completely.
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/