THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Manufacturing Page 1 Factory No. 17052
Date 2014-11-28 Rev. 1
Factory: NIELFU
O'nin White Room Divider
Model # DMRD-W-E
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS,
SHARP POINTS, SHARP EDGES AS RECEIVED
If you have any questions regarding assembly or if parts are missing, DO NOT return this
item to the store where it was purchased. Please call our toll-free customer service number
and have your instructions and parts list ready to provide the model name, part name or
factory number:
866-942-5362 (Service valid only in USA)
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
Or visit our website www.whalenfurniture.com
Or e-mail your request to parts@whalenfurniture.com
LOT NUMBER:
DATE PURCHASED: / /
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 2 Factory No. 17052
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: O’nin White Room Divider (DMRD-W-E)
DATE OF MANUFACTURE: June 2015
MADE IN CHINA
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw Cam Bolt into the threaded insert on panel.
2. Insert Cam Lock into pre-drilled hole on panel.
3. Make sure Cam Lock pointed arrow is pointed towards the entry of Cam Bolt.
4. Connect both panels together; making sure Cam Bolt goes into pre-drilled hole on the
end of panel with Cam Lock.
5. Once Cam Bolt is connected inside Cam Lock, take a Phillips screwdriver and tighten
Cam Lock clockwise.
You are now ready to assemble the KD unit.
MAXIMUM LOAD 100 lb. (45.3 kg)
MAXIMUM LOAD 20 lb. (9 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY
,
CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 200 lb. (90.7 kg)
MAXIMUM RECOMMENDED WEIGHT LOADS
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 3 Factory No. 17052
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A- Top/Bottom Panel (2) B- Side Panel (2)
C- Large Divider Panel (2) D- Center Divider (1)
(With Cam lock holes)
E- Small Divider Panel (4) F- Storage Basket (8) G- Basket Flooring (8)
(1) 2-1/4” Bolt (8+1 extra) (2) Lock Washer (8+1 extra) (3) Flat Washer (8+1 extra)
(4) Cam Lock (4+1 extra) (5) Cam Bolt (4+1 extra) (6) Large Wood Dowel (12+1 extra)
(7) Small Wood Dowel (8) Cam Lock Cover (9) Wood Plug (10) Plastic Cap
(40+1 extra) (4+1 extra) (8+1 extra) (8+1 extra)
Allen Wrench (2) Tipping Restraint Hardware Kit (2)
(Inside Plastic Bag)
Tools required: Allen wrench (provided), Phillips screwdriver and mallet (not provided).
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 4 Factory No. 17052
Assembly Instructions
1. Unpack the unit and confirm that you have all hardware and required parts.
2. Lay the Side Panels (B) on a level and protected surface with the pre-drilled holes facing up. Screw 2
Cam Bolts (5) into the plastic bushings included on the center of each Side Panel. Fully tighten with a
Phillips screwdriver.
3. Insert 4 Small Wood Dowels (7) half way into the pre-drilled holes on the Large Divider Panel (C) by
tapping lightly with a rubber mallet, if necessary. Position 2 Small Divider Panels (E) onto the inserted
Wood Dowels and press them together.
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 5 Factory No. 17052
Assembly Instructions
4. Attach the Center Divider (D) and one Small Divider Panel (E) to the assembled Small Divider Panel
(E) using 4 Small Wood Dowels (7).
5. Repeat the last step to install the remaining Large Divider Panel (C) and Small Divider Panel (E) to
the last assembly. Make certain they are located on the other end of Center Divider (D).
6. Insert 20 Small Wood Dowels (7) into the end holes of Large Divider Panels (C) and Center Divider
(D). DO NOT put dowels into the Cam Bolt holes.
7. Insert 4 Cam Locks (4) into the side holes of the Center Divider (D) making sure the arrow on the face
of Cam Lock points out and towards the entry of Cam Bolt.
8. Position the Side Panels (B) onto the inserted Small Wood Dowels (7). Press them together and
secure in place by connecting the Cam Locks (4) (Refer to page 2 on Cam lock system operation
supplement). Once locked in place, insert the Cam Lock Covers (8) to conceal the Cam Locks.
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 6 Factory No. 17052
Assembly Instructions
9. Insert the Small Wood Dowels (7) into the end holes of both Small Divider Panels (E) and insert 3
Large Wood Dowels (6) into each end of the Side Panels (B).
10. Using the Wood Dowels as a guide, attach Top and Bottom Panels (A) to both Side Panels (B) by
screwing the 2-1/4” Bolts (1) with Lock Washers (2) and Flat Washers (3) into the countersunk holes
on Top/Bottom Panel. Tighten the bolts with the provided Allen Wrench. Cover the countersunk holes
by inserting the Wood Plugs (9) or Plastic Caps (10) provided. Gently tap the Wood Plugs or Plastic
Caps with a rubber mallet to ensure they are fully seated.
11. Ask for assistance to stand the unit upright and position at the desired location in your room.
12. Unfold the Storage Baskets (F) and then place the Basket Flooring (G) inside the open basket to
ensure it remains square. Position the Storage Baskets onto the compartments, as shown.
13. You can combine 2 or more units to create an attractive storage wall for your home.
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 7 Factory No. 17052
TIPPING RESTRAINT HARDWARE
NOTE: We have included two sets of Tipping Restraint Hardware for this unit. You must
install this hardware to prevent accidents or injuries from falling unit.
When properly installed, this restraint can provide protection against the unexpected tipping
of the unit due to small tremors, bumps or climbing. We strongly recommend mounting this
hardware to a wall stud and your unit.
Please carefully read the instructions printed on the plastic bag containing tipping restraint
hardware to attach the tipping restraints to the unit and the wall.
NOTE: Young children can be seriously injured by tipping furniture. You must install the
Tipping Restraint Hardware with the unit to prevent the unit from tipping, causing any
accidents or damage. The tipping restraint is intended only as a deterrent, they are not a
substitute for proper adult supervision. The tipping restraint is not an earthquake restraint. If
you wish to add the extra security of earthquake restraints, they must be purchased and
installed separately.
Tools required: Phillips screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.
Model # DMRD-W-E
Please call for replacement parts or assistance:
866-942-5362
Whalen Furniture Manufacturing Page 8 Factory No. 17052
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an
inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid
rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that
may create spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that
you call a professional to repair your furniture.
Further advice about wood furniture care
It is best to keep your furniture in a climate controlled environment. Extreme temperature
and humidity changes can cause warping, shrinking and splitting of wood. It is advised to
keep furniture away from direct sunlight as may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these
important and helpful tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we
will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture
product is designed to meet your highest expectations. We guarantee that you will
immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary
from State to State.
Customer Service: 866-942-5362 (Service valid only in USA)
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com
IF YOU NEED TO ORDER ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
O'nin White Room Divider (DMRD-W-E)
*DMRD-W-E-1-SP Side Panel *DMRD-W-E-11-WP Wood Plug
*DMRD-W-E-2-TBP Top/Bottom Panel *DMRD-W-E-12-CL Cam Lock
*DMRD-W-E-3-LDP Large Divider Panel *DMRD-W-E-13-CB Cam Bolt
*DMRD-W-E-4-CD Center Divider *DMRD-W-E-14-CLC Cam Lock Cover
*DMRD-W-E-5-SDP Small Divider Panel *DMRD-W-E-15-LWD Large Wood Dowel
*DMRD-W-E-6-SB Storage Basket *DMRD-W-E-16-SWD Small Wood Dowel
*DMRD-W-E-7-BF Basket Flooring *DMRD-W-E-17-PC Plastic Cap
*DMRD-W-E-8-2 1/4B 2-1/4" Bolt *DMRD-W-E-18-AW Allen Wrench
*DMRD-W-E-9-LW Lock Washer *DMRD-W-E-19-TRHK Tipping Restraint Hardware Kit
*DMRD-W-E-10-FW Flat Washer *DMRD-W-E-CH Complete Hardware
/
