Minka Lavery 5411-281 Installation guide

Type
Installation guide

Minka Lavery 5411-281 is a versatile lighting fixture that can be used in various indoor settings. It features a sturdy mounting plate for secure attachment to the outlet box and simple wiring for easy installation. The fixture accommodates a single A19 E26 (MED BASE) light bulb (not included), allowing for customizable lighting intensity. With its elegant glass shade and metal ring, the Minka Lavery 5411-281 adds a touch of sophistication to any room's decor.

Minka Lavery 5411-281 is a versatile lighting fixture that can be used in various indoor settings. It features a sturdy mounting plate for secure attachment to the outlet box and simple wiring for easy installation. The fixture accommodates a single A19 E26 (MED BASE) light bulb (not included), allowing for customizable lighting intensity. With its elegant glass shade and metal ring, the Minka Lavery 5411-281 adds a touch of sophistication to any room's decor.

INSTALLATION INSTRUCTIONS
Item#5411-281 (New. 01/15/2015)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker and
remove old fixture, including the mounting
hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Attach mounting plate (B) to the outlet box (A) (not
included) with mounting screws (C)
(
s
ize:
#8-32N*L0.5”)
. The side of the mounting plate
Marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
4. At this point, connect the electrical wires as shown
in Fig. 2, making sure that all wire connectors are
secured. If your outlet box has a ground wire
(green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate using the
green screw provided. After wires are connected,
tuck them carefully inside the junction box.
FINISHING THE INSTALLATION (Fig.1)
5. Place fixture body (D) over mounting plate (B), and
secure with screws (E).
6. Place the glass shade (F) followed by metal ring
(G) over the socket, fasten with screw shell (H) by
using the tool (I).
7.
Install the A19 E26 (MED BASE) light bulb (not
included) in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!)
(NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power
and test the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2441E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
E
D
C
F
G
H
I
A
B
Socket ring # SKT-RING-26
E26 Socket Spanner: WRH-1-51
Set
A
-
02
1
-
150119
-Mounting Plate
-Ground screw
-Mounting Screw*2
  • Page 1 1

Minka Lavery 5411-281 Installation guide

Type
Installation guide

Minka Lavery 5411-281 is a versatile lighting fixture that can be used in various indoor settings. It features a sturdy mounting plate for secure attachment to the outlet box and simple wiring for easy installation. The fixture accommodates a single A19 E26 (MED BASE) light bulb (not included), allowing for customizable lighting intensity. With its elegant glass shade and metal ring, the Minka Lavery 5411-281 adds a touch of sophistication to any room's decor.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI