George Kovacs P1700-613 User manual

Brand
George Kovacs
Model
P1700-613
Type
User manual

George Kovacs P1700-613 is a lighting fixture designed for indoor use. It can be mounted on a ceiling or wall and provides ample lighting for a variety of spaces, including living rooms, bedrooms, and hallways. The fixture is made of high-quality materials and features a modern design that will complement any décor.

The P1700-613 is easy to install and comes with all the necessary hardware. It requires a single T10 1*60W (MED BASE) light bulb, which is not included. The fixture is dimmable, allowing you to customize the light output to suit your needs.

George Kovacs P1700-613 is a lighting fixture designed for indoor use. It can be mounted on a ceiling or wall and provides ample lighting for a variety of spaces, including living rooms, bedrooms, and hallways. The fixture is made of high-quality materials and features a modern design that will complement any décor.

The P1700-613 is easy to install and comes with all the necessary hardware. It requires a single T10 1*60W (MED BASE) light bulb, which is not included. The fixture is dimmable, allowing you to customize the light output to suit your needs.

INSTALLATION INSTRUCTIONS
Item#P1700-647/613 (New. 03/01/2012)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUI T BRE AKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker and remove
the old fixture, including the mounting hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Attach mounting plate (B) to the outlet box (A) (not
included) with mounting screws (C) (size:
#8-32N*L0.5”) The side of the mounting plate
marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
4. At this point, connect the electrical wires as shown
in Fig. 2, making sure that all wire connectors are
secured. If your outlet box has a ground wire (green
or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire
directly to the mounting plate using the green screw
provided. After wires are connected, tuck them
carefully inside the junction box.
FINISHING THE INSTALLATION (Fig.1)
5. Place fixture body (D) over mounting plate (B), and
secure with screws (E).
6. Place the glass shade (F) followed by metal ring (G)
over the socket. Use tool (I) and screw shell (H) to
secure the glass into the fixture body.
7. Install the T10 1*60W (MED BASE) light bulb (not
included) in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power and
test the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2110E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
H
G
F
B
C
E
D
I
A
Socket Ring#
SKT-RING-26(#H)
  • Page 1 1

George Kovacs P1700-613 User manual

Brand
George Kovacs
Model
P1700-613
Type
User manual

George Kovacs P1700-613 is a lighting fixture designed for indoor use. It can be mounted on a ceiling or wall and provides ample lighting for a variety of spaces, including living rooms, bedrooms, and hallways. The fixture is made of high-quality materials and features a modern design that will complement any décor.

The P1700-613 is easy to install and comes with all the necessary hardware. It requires a single T10 1*60W (MED BASE) light bulb, which is not included. The fixture is dimmable, allowing you to customize the light output to suit your needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents