Dell EqualLogic PS4210X Owner's manual

Brand: Dell

Model: EqualLogic PS4210X

Type: Owner's manual

Dell EqualLogic PS4210 Storage Arrays

Installation and Setup Guide



Dell EqualLogic PS4210 Storage Arrays

Installation and Setup Guide

Version 1.0

Regulatory Model Series E03J and E04J

©Copyright2014DellInc.Allrightsreserved.

Dell™andEqualLogic®aretrademarksofDellInc.Alltrademarksandregisteredtrademarksmentionedherein

arethepropertyoftheirrespectiveowners.

Informationinthisdocumentissubjecttochangewithoutnotice.

ReproductionofthismaterialinanymannerwhatsoeverwithoutthewrittenpermissionofDellisstrictly

forbidden.

Published:October2014

PartNumber:M40C6-A00

Table of Contents
Preface
v
1  Understanding the Array Installation Procedure
1
2  Rack Mounting the Array
3
BeforeYouBegin 3
ProtectingHardware 4
StepsforMountinganArrayinaRack 6
3  Connecting the Array Cables
9
NetworkRequirementsandRecommendations 9
MinimumandRecommendedCableConfigurations 10
ConnectandSecurethePowerCables 11
ConnecttheArraytotheNetwork 12
SetUpaSerialConnectiontotheArray 13
4  Software Configuration
17
ChooseaConfigurationMethod 17
CollectConfigurationInformation 17
StarttheSoftwareConfiguration 18
SettheMemberRAIDPolicy 21
5  Storage Allocation
23
CreateaVolume 23
ConnectaComputertoaVolume 27
6  Where to Go After Setting Up a Group
29
CommonGroupCustomizationTasks 29
7  Other Information You Might Need
31
NOMInformation(MexicoOnly) 31
Index
35
iii

Installation and Setup Guide Table of Contents

Preface

Dell™EqualLogic®PSSeriesarraysoptimizeresourcesbyautomatingcapacity,performance,andnetwork

loadbalancing.Additionally,PSSeriesarraysofferall-inclusivearraymanagementsoftwareandfirmware

updates.DellEqualLogicFSSeriesappliances,combinedwithPSSeriesarrays,offerahigh-performance,high-

availability,scalableNASsolution.

Audience

Theinformationinthisguideisintendedforhardwareadministrators.Administratorsarenotrequiredtohave

extensivenetworkorstoragesystemexperience.However,itishelpfultounderstand:

• Basicnetworkingconcepts

• Currentnetworkenvironment

• Userdiskstoragerequirements

• RAIDconfigurations

• Diskstoragemanagement

Note: AlthoughthismanualprovidesexamplesofusingPSSeriesarraysinsomecommonnetwork

configurations,detailedinformationaboutsettingupanetworkisbeyonditsscope.

Related Documentation

FordetailedinformationaboutPSSeriesarrays,groups,volumes,arraysoftware,andhostsoftware:

1. LogintotheDellEqualLogicsupportsite(eqlsupport.dell.com).

2. SelectDownloads.

3. Fromthedrop-downlist,choosePS Series Firmware.

4. UnderRecommendedPSSeriesFirmware,selecttherequiredversion.Thelinktothedownloadpage

appears.

5. ClicktheDownloadpagelink.

6. ScrolldowntoDocumentation.

Dell Online Services

YoucanlearnaboutDellproductsandservicesbyvisitingdell.com(ortheURLspecifiedinanyDellproduct

information).

TolearnmoreaboutDellEqualLogicproductsandnewreleases,visittheDellEqualLogicTechCentersite:

delltechcenter.com/page/EqualLogic.Hereyoucanalsoseearticles,demos,onlinediscussions,andmoredetails

aboutthebenefitsofourproductfamily.

Technical Support and Customer Service

Dell’ssupportserviceisavailabletoansweryourquestionsaboutPSSeriesSANarrays.IfyouhaveanExpress

ServiceCode,haveitreadywhenyoucall.ThecodehelpsDell’sautomated-supporttelephonesystemdirect

yourcallmoreefficiently.

Installation and Setup Guide Preface

Contacting Dell

Dellprovidesseveralonlineandtelephone-basedsupportandserviceoptions.Availabilityvariesbycountryand

product,andsomeservicesmightnotbeavailableinyourarea.

TocontactDellEqualLogicTechnicalSupportbyphone,ifyouarelocatedintheUnitedStates,call800-945-

3355.ForalistingofInternationalDellEqualLogicsupportnumbers,visitdell.com/support/home.Fromthis

website,selectyourcountryfromthedrop-downlistintheupperleftcornerofthescreen.Ifyoudonothave

accesstoanInternetconnection,contactinformationisprintedonyourinvoice,packingslip,bill,orDellproduct

catalog.

UsethefollowingproceduretoregisterforanEqualLogiccustomersupportaccount,tologcasesviatheweb,

andtoobtainsoftwareupdates,furtherdocumentationandresources.

1. Visiteqlsupport.dell.comortheDellsupportURLspecifiedininformationprovidedwiththeDellproduct.

2. Selecttherequiredservice.ClicktheContact Uslink,orselecttheDellsupportservicefromthelistof

servicesprovided.

3. ChooseyourpreferredmethodofcontactingDellsupport,suchase-mailortelephone.

Warranty Information

ThePS4210arraywarrantyisincludedintheshippingbox.Forinformationaboutregisteringawarranty,visit

https://eqlsupport.dell.com/utility/form.aspx?source=warranty.

Notes, Cautions, and Warnings Symbols

ANOTEsymbolindicatesimportantinformationthathelpsyoumakebetteruseofyourhardwareorsoftware.

ACAUTIONsymbolindicatespotentialdamagetohardwareorlossofdataifinstructionsarenotfollowed.

AWARNINGsymbolindicatesapotentialforpropertydamage,personalinjury,ordeath.

Further Information

Forbasicstoragearrayinformation,maintenanceinformation,andtroubleshootinginformation,refertothe

PS4210HardwareOwner'sManual.

1  Understanding the Array Installation Procedure
TosetupyourarrayandstartusingtheiSCSISANarray,followthesesteps:
1. Installthearrayinarack.SeeRack Mounting the Array on page 3.
2. Connectthearraytopowerandthenetwork.SeeConnect and Secure the Power Cables on page 11and
Connect the Array to the Network on page 12.
3. ConfigurethePSSeriessoftware.First,initializeanarraytomakeitaccessibleonthenetwork.Then,either
createagroupwiththearrayasthefirstgroupmemberoraddthearraytoanexistinggroup.Whenyou
expandagroup,capacityandperformanceincreaseautomatically.SeeChoose a Configuration Method on 
page 17.
4. StartusingtheiSCSISANarray.Allocategroupstoragespacetousersandapplicationsbycreating
volumes.AvolumeappearsonthenetworkasaniSCSItarget.Useacomputer’siSCSIinitiatortoconnect
toavolume.Afteryouconnecttoavolume,itappearsasaregulardiskonthecomputer.SeeStorage 
Allocation on page 23.
Aftergettingstarted,youcancustomizethegroupanduseitsmoreadvancedfeatures.SeeWhere to Go After 
Setting Up a Group on page 29.
1

PS4210 Hardware Owner's Manual

1 Understanding the Array Installation Procedure

2 Rack Mounting the Array

Forproperoperation,aPSSeriesstoragearraymustbeproperlyinstalledinarack.Thissection

containsgeneralelectrostatic,safety,network,andinstallationinformationforPSSeriesarrays.

Afterinstallingthearrayinarack,connectthepowerandnetworkcables,asdescribedin

Chapter 3.

Before You Begin

Beforeinstallingthearray:

• RegisterforaDell™EqualLogic®CustomerSupportAccount.Ifyoudonothavea

customerservicesupportaccount,gotoeqlsupport.dell.comandcreateone.

• DownloadandreadtheReleaseNotesfromtheSupportSite.ThePS Series Storage Arrays

Release Notescontainthelatestproductinformation.

• Readtheinstallationsafetyprecautions.SeeInstallation Safety Precautions on page 3.

• Makesuretherackmeetstherackrequirements.SeeRack Requirements on page 3.

• Makesurethearrayandinstallationlocationmeettheenvironmentalrequirements.See

Environmental Requirements on page 4.

• Unpacktherailkit(ifordered)andmakesureyouhaveallthenecessarypartsandtools.

Therailkitislocatedinthearrayshippingbox.Youmustsupplyyourowntools.See

Shipping Box Contents and Required Hardware on page 5.

Installation Safety Precautions

Followthesesafetyprecautions:

• Dellrecommendsthatonlyindividualswithrack-mountingexperienceinstallanarrayina

rack.

• Makesurethearrayisfullygroundedatalltimestopreventdamagefromelectrostatic

discharge.

• Whenhandlingthearrayhardware,youmustusetheelectrostaticwristguardshippedwith

thearrayorasimilarformofprotection.

• Youneedatleasttwopeopletoliftthearraychassisfromtheshippingbox.

Rack Requirements

Therackandthearrayinstallationmustmeetthefollowingrequirements:

• Useanindustry-standard,EIA-310-Dcompliant,four-post19-inchrackwithuniversal

squareholeorunthreadedroundholespacing.

• Therackisratedfor540kg(1200pounds)staticloadorgreater.

• Theminimumrackdepthis100cm(40inches)fromthefrontoftheracktotherearofthe

rack.

• FortheReadyRails™IIrailkits,thedistancebetweentheoutsidesurfacesofthefrontand

rearrackposts(themountingsurfaces)canrangefrom595mmto914mm(23.4”to36.0”)

forsquare-holeracks,581mmto907mm(22.9”to35.7”)forround-holeracks,and595mm

to929mm(23.4”to36.6”)forthreaded-holeracks.

• Therackissecuredtothefloorforaddedstability.

• Loadarackwitharraysfromthebottomtothetop.

• Thereisatleast4.1cm(1.6inches)betweentherackdoorandthefrontofthearrayto

accommodatethearrayfrontbezel.

• Therack(withinstalledarrays)meetsthesafetyrequirementsofUL60950-1andIEC

60950-1,availableatulstandardsinfonet.ul.com/scopes/scopes.asp?fn=60950-1.html.

• Mountthearrayinahorizontalorientationoryouwillvoidyourarraywarrantyandsupport

contract.

Environmental Requirements

Theracklocationmustmeetthefollowingenvironmentalrequirements:

• Thepowersourcecansupplyavoltagerangeof100Vto240VAC.

• Thepowersourcehassufficientelectricaloverloadprotection:

InNorthAmerica,connectthearraytoasourceofpowerwithover-currentprotection

providedbyadoublepole20Aorlessdevice(UL489circuitbreakers).

InEurope,theover-currentprotectionmustbeprovidedbya20Aorlessdevice(IEC

circuitbreakers).

• Thereissufficientspaceforairflowinfrontofandbehindthearray.

• Thelocationisproperlyvented.

• YourenvironmentsupportsalloftherequirementslistedintheTechnical Specifications on

page 31.

Protecting Hardware

ProtectyourPSSeriesarrayfromelectrostaticdischarge.Whenhandlingarrayhardware,usean

electrostaticwriststraporasimilarformofprotection.Touseawriststrap:

1. Connectthesteelsnaponthecoilcordtothestudontheelasticband.SeeFigure1.

Figure 1: Using an Electrostatic Wrist Strap

2. Fitthebandtightlyaroundyourwrist.

PS4210 Installation Guide 2 Rack Mounting the Array

3. Connectthebandtoground.Youcaneitherplugthebananaconnectorintoamatching

groundedreceptacle,orattachittothematchingalligatorclipandconnectthecliptoa

groundeddevice.ExamplesofanappropriategroundwouldbeanESDmatorthemetal

frameofagroundedpieceofequipment.

Shipping Box Contents and Required Hardware

Makesureyouhavealltheitemssuppliedintheshippingbox,describedinTable1.Youmust

provideadditionalhardwarethatisspecifictoyourenvironmentandnotincludedintheshipping

box.SeeTable2.

Table 1: Shipping Box Contents

Component Description

PSSeriesArray

• TwoType19controlmodules

• Twopowersupplyandcoolingmodules

• Upto242.5-inch10Kor123.5-inch7.2Kserial-attachedSCSI(SAS,

NearlineSAS[NL-SAS],orSolidState(SSD)drives,dependingonthe

modelsuffix

Bezel

Thebezelmountstothefrontofthearray.Thebezelidentifiesthearray

modelandprotectsthedrivesfromunauthorizedoraccidentalremoval.

Powercables

Connectsanarraypowersupplytopowersources.Ifpowercablesarenot

includedintheshippingbox,contactyourPSSeriesarraysupportprovideror

reseller.

Oneortwoserial

cables

Createsaserialconnectionbetweenanarrayandaconsoleorterminal

emulator.Usethecabletorunthesetuputilityifthereisnonetworkaccess

tothearrayorgroup.

Documentation

Thefollowingdocumentationisincludedintheshippingbox:

• Setupposter

• InstallationandSetupGuide(thisdocument)

• License,regulatory,andwarrantyinformation

• Safety,Environmental,andRegulatoryInformationbooklet

Table 2: Additional Hardware Required (Not Included)

Component Description

Standard19-in.

four-postrack

Provideseasyaccesstoarraysandotherhardwareinyourcomputing

environment.

10/100Mbps

Ethernetcables

Forusewithadedicatedmanagementnetwork.ConnectstheManagementporton

thearraytoa10/100Mbpsnetworkswitch.UseCategory5EorCategory6cables

withRJ45connectors.UseCategory5cablesonlyiftheymeettheTIA/EIA

TSB95standard.

Networkswitch

Connectsdevices(array)toanetwork.Multipleswitchesarerecommended.

Switchprovides10GBASE-Tinterfacestousethe10GBASE-Tport,oran

SFP+switchtousetheSFP+port.

CAT6orCAT6A

cables

For10GBASE-Tport,useCategory6(orbetter)cableforupto55meters.Use

Category6Acableforupto100meters.

Opticalorcopper

cables

ForSFP+port,useopticalcableorcopperSFP+cable.

Optional Hardware

Youcanoptionallyuseanuninterruptiblepowersupplysystem(UPS)toprovideahighly

availablesourceofpowertoanarray.EachUPS(notincluded)shouldbeonadifferentcircuit

andmustprovidethecorrecttypeofvoltageforanadequateamountoftime.

Steps for Mounting an Array in a Rack

Tomountanarrayinarack,followthesesteps:

1. Determinewheretoplacethemountingrailsintherack.

2. Attachthemountingrailstotherack.

3. Slidethechassisintotherack.

4. Attachthechassistothefrontofthemountingrails.

5. Installthebezel.

Thesestepsaredescribedindetailinthefollowingsections.

Determine Where to Place the Mounting Rails in the

Rack

Makesurethereisenoughspaceintherackforthechassis.Inastandardrack,a2Uchassis

willspansixholes.

Installing the Rails and Array in a Rack

Installtherailsintherackfollowingthesafetyinstructionsandtherackinstallationinstructions

providedwithyourrailkit.

Ifinstalledinaclosedormulti-unitrackassembly,theoperatingtemperatureoftherack

environmentmightbegreaterthanroomambient.Therefore,makesureyouinstallthearrayin

anenvironmentcompatiblewiththemaximumtemperaturespecifiedbythemanufacturer.For

moreinformation,seeTechnical Specifications on page 31.

Slide the Array into the Rack

SlidethearrayintotherackasshowninFigure2.

PS4210 Installation Guide 2 Rack Mounting the Array

Figure 2: Installing the Array Into the Rack

Figure3showsthefrontviewofthe3.5-inchdrivearray.

Figure 3: 3.5-Inch Drive Array - Front View (Without Bezel)

Figure4showsthefrontviewofthe2.5-inchdrivearray.

Figure 4: 2.5-Inch Drive Array - Front View (Without Bezel)

Withassistance,liftthearray,keepingthearraylevel,andslideitontothemountingrailsuntil

thearrayengages.

Attach the Array to the Mounting Rails

Makesurethearraycaptivefastenersonthefrontofthearraylineupwiththethreadedholeson

thefrontofthemountingrails,andmanuallysecurethecaptivefastenerstotherails.

Note: Donotovertightenthethumbscrews.

Installing the Bezel

Thestepsforinstallingthebezelarethesameforallarraymodels:

1. Hooktherightendofthebezelontotherightsideofthechassis.

2. Swingtheleftendofthebezeltowardtheleftsideofthechassis.

3. Pressthebezelintoplaceuntilthereleaselatchcloses.

4. Usingthekeyprovided,lockthebezelandstorethekeyinasafeplaceasshowninFigure

Figure 5: Installing the Bezel

PS4210 Installation Guide 2 Rack Mounting the Array

3 Connecting the Array Cables

Afteryouinstallthearrayinarack,youmustconnectthenetworkandpowercablesand,

optionally,theserialcables.

First,reviewthenetworkrecommendationsinMinimum and Recommended Cable

Configurations on page 10.

Thefollowinglistdescribesthegeneralstepsforconnectingthearraytopowerandthenetwork:

1. Connectthepowercables.Donotturnonpowertothearrayatthistime.SeeConnect and

Secure the Power Cables on page 11.

2. Connectthearraytothenetwork.SeeConnect the Array to the Network on page 12.

3. Turnonpowertothearray.SeeTurning On the Array on page 12.

Thefollowingsectionsdescribethesestepsindetail.Aftercompletingthesteps,seeSoftware

Configuration on page 17.

Network Requirements and Recommendations

TheminimumnetworkconfigurationforaPSSeriesarrayconsistsofaconnectionbetween

Ethernet0oneachcontrolmoduleandacomputerconnectedtoanetworkswitch.Toincrease

performanceandavailability,configuremultiplenetworkinterfacesonanarrayandconnect

themtomultipleswitches.

NetworkrecommendationsaredescribedinTable3.Inaddition,alltheusualrulesforproper

networkconfigurationapplytoPSSeriesarrays.Formoreinformationaboutnetwork

requirements,seetheDellEqualLogicConfigurationGuideontheDellTechCenterwebsiteat

en.community.dell.com/techcenter/storage/w/wiki/2639.equallogic-configuration-guide.aspx.

Generalnetworkconfigurationisbeyondthescopeofthismanual.

Table 3: Network Recommendations

Recommendation Description

Switched10GbE

network

Connectarraysandcomputerstoaswitchednetworkandensurethatall

networkconnectionsbetweencomputersandarraysare10GbE.

UseopticalcableswithopticalSFP+plug-inmodules,orcoppercableswith

integratedSFP+modules.10GBASE-TrequiresCat6minimally,butCat6Ais

recommended.

Requiresaswitchwith10GBASE-Tinterfacestousethe10GBASE-Tport,or

anSFP+switchtousetheSFP+port.

Multiplenetwork

connectionsto

differentnetwork

switches

Forincreasedbandwidthandavailability,connecteachcontrolmoduletotwo

differentswitches.

Theswitchesmustbeconnectedusinginterswitchlinksorbystacking

capability.ThelinksmusthavesufficientbandwidthtohandletheiSCSI

traffic.ReviewtheEqualLogicConfigurationGuideforinterswitchlinksizing

recommendations.

Afterconnectingthenetworkinterfaces,usetheGroupManagerGUIorCLIto

assignanIPaddress,netmask,andgatewayaddresstoeachinterface.

Recommendation Description

Management

network(optional)

Connectthemanagementportsonbothcontrolmodulestoa10/100Mbps

networkswitchtokeepmanagementtrafficseparatefromiSCSItraffic.

Accesstothegroup

IPaddress(Hosts)

Inamulti-subnetgroup,eachconfigurednetworkinterfaceshouldhaveaccess

tothesubnetonwhichthegroupIPaddressresides.

Forreplication,a

reliable,adequately

sizednetworklink

Foreffectiveandpredictablereplication,thenetworklinkbetweentheprimary

andsecondarygroupsmustbereliableandprovidesufficientbandwidthfor

copyingdata.

Useofspanning-tree

protocol

Ifpossible,donotuseSpanningTreeProtocol(STP)onswitchportsthat

connectendnodes(iSCSIinitiatorsorarraynetworkinterfaces).

IfyoumustuseSTPorRSTP(STPispreferable),enabletheportsettings

(availableonsomeswitches)thatlettheportimmediatelytransitionintoSTP

forwardingstateuponlinkup.Thisfunctionalitycanreducenetwork

interruptionsthatoccurwhendevicesrestart,andshouldbeenabledonlyon

switchportsthatconnectendnodes.

YoucanuseSTPforasingle-cableconnectionbetweenswitchesandtrunking

formulticableconnectionsbetweenswitches.

VLANs

TouseDCB(DataCenterBridging),configureswitchestouseVLANsto

separateiSCSISANtrafficfromothernetworktraffic.

DCB

YoumusthaveVLANsenabled.RefertotheDell EqualLogic Group Manager

Administrator's Manual,andtheDellEqualLogic Group Manager

CLI Reference GuideformoreinformationaboutDCB.

Minimum and Recommended Cable

Configurations

Foradualcontrolmodulearray,therecommendedconfigurationistoconnectnetworkcablesto

Ethernet0onbothcontrolmodules,andconnecteachcontrolmoduletoanetworkswitch.

Forhighperformanceandavailability,distributetheconnectionsacrossmultiplenetwork

switches.

Theswitchesmustbeconnectedwithinterswitchlinksthathavesufficientbandwidthtohandle

theiSCSItraffic,orbystackingcapability.Dellrecommendsusingstackingconfigurations

whereverpossible.

Figure6illustratestherecommendednetworkconfigurationalternatives.

Note: DelldoesnotrecommendconnectingboththeSFP+and10GBASE-TEthernetportsat

thesametime.

PS4210 Installation Guide 3 Connecting the Array Cables

Figure 6: Recommended Network Configurations

Connect and Secure the Power Cables

Obtainthepowercablesthatwereshippedwiththearray.Ifthearraywasnotshippedwith

powercables,contactyourPSSeriessupportproviderorresellerforpowercableinformation.

1. MakesurethatthepowerswitchisintheOFF(O)positionbeforeconnectingthepower

cables.

2. Connectthepowercablestothepowersuppliesasshownin.

3. Securethepowercablestothesystem:

a. Securethepowercablesfirmlytothebracketnexttothesystempowerreceptacle

usingtheprovidedhook-and-loopstrap.

b. Makesurethestrapistightlyboundtothebracketanchorpoint(removeanyslack).

c. Biasthepowercabletowardthestrapandwrapthestraptightlyaroundthecable

againsttheshoulderofthepowercableconnector.

4. Attachthepowercablestoapowersource:

– Plugthepowercablesintoagroundedelectricaloutletoraseparatepowersourcesuch

asanuninterruptedpowersupply(UPS)orapowerdistributionunit(PDU).Thebottom

LEDofthepowersupplywillbeilluminatedgreen(indicatingpowerispresent)when

powercablesareconnected.

– EachUPS(notincluded)shouldbeonadifferentcircuitandmustprovidethecorrect

typeofvoltageforanadequateamountoftime.

– Alternately,connectonepowersupplyandcoolingmoduletoaUPSsystemandconnect

theothermoduletoadifferentsourceofpower.

Caution: Donotturnonpowertothearrayyet.

Figure 7: Connecting the AC Power Cables

Connect the Array to the Network

ThePS4210arraymodelincludestwoType19controlmodules.EachType19controlmodule

includestwo10Gbase-Tportsandtwo10GbeSFP+ports.Ofeachpair,oneislabeledEthernet

0andtheotherislabeledEthernet1.

Thecontrolmodulesalsoincludeone10Mb/100MbportlabeledManagement.Themanagement

portcannotcarryiSCSItraffic.Usethemanagementportonlyifyouconfigureamanagement

network.SeetheDell EqualLogic Group Manager Administrator's Manualformoreinformation.

Obtaintheappropriatenumberofcopperoroptical10GbEnetworkcables.

Note: Opticalcablestransmitdatathroughpulsesoflight.Itisveryimportanttoroutealloptical

cableswithnomorethana4-inchbendradiusatanypointbetweenthearrayandtheswitch.

Onefunctioningnetworkconnectionisrequiredforarrayoperation.Multiplenetwork

connectionsarerecommendedforperformanceandhighavailability.SeeMinimum and

Recommended Cable Configurations on page 10foradditionalinformation.

Turning On the Array

Beforeturningonpower,allowsufficienttimeforthearraytoadjusttoambienttemperature(for

example,overnight).

Note: Youcanturnonthepowertoonepowersupplyfirst(eitherone),orbothatthesame

time.

PS4210 Installation Guide 3 Connecting the Array Cables

Page is loading ...

Dell EqualLogic PS4210X Owner's manual

Dell EqualLogic PS4210X Owner's manual

Dell EqualLogic PS4210X Owner's manual

Related papers

Other documents