Bosch CIP‑5316W‑00N Quick Installation Manual

Brand: Bosch

Model: CIP‑5316W‑00N

Type: Quick Installation Manual

This manual is also suitable for

CIP5000 series storage

CIP‑5316W‑00N / CIP‑5424W‑00N

Quick installation guide

CIP5000 series storage Table of contents | en 3

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

Table of contents

Safety 4

1.1 RoHS compliance 4

About this guide 5

2.1 Introduction 5

System overview 6

3.1 Front panel 6

3.2 Rear panel 6

3.2.1 Rear panel components 7

3.3 Secure cover 8

3.3.1 Install the cover 9

Setup tasks 10

4.1 Task 1: unpacking 10

4.2 Task 2: install enclosure on the rack 10

4.3 Task 3: install disk drives 13

4.3.1 Drive slot numbering 13

4.3.2 Remove the drive carrier 14

4.3.3 Install 3.5" disk drive in the carrier 15

4.4 Task 4: establish I/O connections 15

4.4.1 Initial setup 16

4.4.2 Network connection 16

4.5 Task 5: connect power and power on 16

4.5.1 Power on 17

4.5.2 Front panel LED behavior 18

4.5.3 Disk drive LEDs 18

4.5.4 PSU LEDs 18

4.5.5 Rear panel LED behavior 19

4.6 Task 6: login to windows 19

4.7 Task 7: create logical drives 19

4.7.1 Log into management GUI 20

4.7.2 Choose a language 20

4.7.3 Create logical drives 20

4.7.4 Log out 24

4.8 System shutdown 24

Technical support 25

Disposal 26

4 en | Safety CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

1 Safety

Warning!

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Danger!

Consequences The electronic components within the enclosure are sensitive to damage from

Electro-Static Discharge (ESD). Observe appropriate precautions at all times when handling

the device or its subassemblies.

Warning!

Turn off the power and disconnect the power cord before servicing this device.

1.1 RoHS compliance

CIP5000 series storage

Hazardous substance table according to SJ/T 11364-2014

(Pb)

(Hg)

(Cd)

Cr 6+

(Cr 6+)

PBB

(PBB)

PBDE

(PBDE)

PCBA X O O O O O

Housing & enclosures X O O O O O

Cables O O O O O O

Power supply units X O O O O O

Batteries X O O O O O

This table was created according to the provisions of SJ/T 11364

O: The content of such hazardous substance in all homogeneous materials of such

component is below the limit defined in GB/T 26572

X: The content of such hazardous substance in a certain homogeneous material is above the

limit defined in GB/T 26572

CIP5000 series storage About this guide | en 5

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

2 About this guide

This document gives a brief overview of the CIP5000 series storage, and then provides

instructions to install the system hardware in the rack, and configure necessary network and I/

O device connections.

For more details on installation and operation of the CIP5000 series storage, refer to the User

manual.

2.1 Introduction

Models included in this guide

Model Interface Number of drives Power supplies Cooling units

CIP-5316W-00N 1000 BASE-T x 2 16 2 2

CIP-5424W-00N 1000 BASE-T x 2 24 2 2

6 en | System overview CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

3 System overview

This section gives an overview of the front panel, rear panel and secure cover of CIP5000

series storage.

3.1 Front panel

The front panel hardware components on the CIP-5316W-00N and CIP-5424W-00N are

identical except the number of drives.

Drive carriers Power and Status LEDs

Figure3.1: CIP-5316W-00N front view

Drive carriers Power and Status LEDs

Figure3.2: CIP-5424W-00N front view

Defective drives shall be replaced immediately in order to ensure data availability. If any drive

failed, a hot spare drive automatically replaces a failed drive, thus ensuring the fault-tolerant

integrity of the logical drive. The self-contained hardware-based RAID logical drives provide

maximum performance in a compact external enclosure.

3.2 Rear panel

The rear panel of CIP-5424W-00N is almost the same as the rear panel of the CIP-5316W-00N

except for its higher profile. The form factor of the CIP-5424W-00N is 4U and the form factor

of the CIP-5316W-00N is 3U.

The rear panel is where you connect power cables, I/O connections, IPMI port, audio out/in,

video (VGA), USB serial ports, COM1 (serial port) and SAS port Backend Controller card. Both

enclosures include PCIe slots for added system versatility.

CIP5000 series storage System overview | en 7

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

Figure3.3: CIP-5316W-00N rear view

Figure3.4: CIP-5424W-00N rear view

3.2.1 Rear panel components

The rear panel components of CIP-5316W-00N and CIP-5424W-00N are the same, and each

model has two power supply units (PSU).

4 6 7 95 8

1 PSU fan vents

2 Power inserts

3 System fan vents

4 PS/2 mouse/keyboard port

8 en | System overview CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

5 VGA port

6 DVI port

7 HDMI port

8 USB 3.0 (4 ports)

9 Optical SPDIF Out port

10 Audio In/Out ports

11 1000BASE-T RJ-45 (2 ports)

3.3 Secure cover

The CIP5000 enclosure include a secure cover for better physical security and to prevent

unintended or accidental removal of hard drives.

The cover are secured with a single tubular cam lock located near the left side of the cover.

Turn the key clockwise to lock, counter clockwise to unlock.

Tubular cam lock

Figure3.5: CIP-5316W-00N with secure cover (unlocked)

Tubular cam lock

Figure3.6: CIP-5424W-00N with secure cover (locked)

CIP5000 series storage System overview | en 9

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

3.3.1 Install the cover

Figure3.7: Installing or removing secure cover

To attach the secure cover:

1. Make sure the lock is in the unlocked position. To unlock, insert the key into the lock and

turn counter clockwise.

2. Insert the tab on the right side of the cover into the slot receptacle on the right handle.

3. Place the cover in position and push in the latch release (to the left of the keyhole).

4. Push the cover into position so that the tab on the right side inserts into the receptacle

on the right handle when releasing the latch.

5. Insert the key and turn clockwise to lock.

To remove the cover, unlock it, press the latch release on the left side and pull the left end out

first, holding it with both hands.

10 en | Setup tasks CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

4 Setup tasks

Finish the basic setup tasks described in the guide.

4.1 Task 1: unpacking

Note that the two models are nearly identical, except for the number of disk drive bays.

Packing List

The box contains the following items:

– One of the following storage appliances:

– CIP-5316W-00N

– CIP-5424W-00N

– Two 1.83m (6 ft) power cords

– Screws for disk drives

– Front panel bezel cover

– Quick installation guide

– (Optional) Sliding rail assembly for rack mounting

4.2 Task 2: install enclosure on the rack

The instructions here apply to 3U 16-bay models CIP-5316W-00N and the JBOD expansion

CIP-5316-JBOD, as well as the 4U 24-bay model CIP-5424W-00N.

Caution!

Do not populate any enclosure hardware with hard drives until it has been securely installed

in the rack.

Caution!

At least two persons are required to safely lift, place, and attach the enclosure hardware into

a rack system.

Caution!

Do not lift or move the enclosure hardware by the handles, or power supplies. Hold the

system itself.

Caution!

Do not install the enclosure hardware into a rack without rails to support the system.

Caution!

Only a qualified technician who is familiar with the installation procedure should mount and

install the enclosure hardware.

Caution!

Mount the rails to the rack using the appropriate screws and flange nuts, fully tightened, at

each end of the rail.

CIP5000 series storage Setup tasks | en 11

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

Caution!

Do not load the rails unless they are installed with screws as instructed.

Caution!

The rails available for the CIP enclosure hardware are designed to safely support that CIP

enclosure hardware when properly installed. Additional loading on the rails is at the

customer’s risk.

Caution!

Bosch cannot guarantee that the mounting rails will support your CIP enclosure hardware

unless you install them as instructed.

Install the enclosure to the rack using the optional rails.

Notice!

To lighten the enclosure, you can remove the power supplies. Replace the power supplies

after the unit is mounted on the rack.

Support flange on the

front end of each rail

Front right label

Front left label

Guide pins on rails align with

holes in the rack post

Figure4.1: Installing the rails onto the rack

12 en | Setup tasks CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

Rail ends attach on

the outside of the front

and rear rack posts

Figure4.2: Rail ends attach to the outside of each post

Rails installed

and tightened

Brackets

3U 16-bay

enclosure hardware

Figure4.3: Placing the enclosure hardware onto the rack rails

Screws and flange

nuts attach the

enclosure hardware

to the rack posts

Figure4.4: Secure to rack

CIP5000 series storage Setup tasks | en 13

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

Handles mount

outside the rack post

Mounting rails mount

outside the rack post

Vertical rack post

Figure4.5: System installed in rack

To install the enclosure hardware into a rack with the supplied rails:

1. Check the fit of the rails in your rack system.

2. Adjust the length of the rails as needed.

– The rear half of the rail slides inside the front half. The rail halves are riveted

together, so no adjustment screws are needed.

– The front-left and front-right rail ends are labeled.

– Be sure the front rail support is on the bottom facing inward.

– All rail ends, front and rear, attach at the outside of the rack posts.

– The guide pins at the rail ends align with the holes in the rack posts.

– Use the attaching screws and flange nuts from your rack system. Tighten the screws

and nuts according to instructions for your rack system.

3. Place the enclosure hardware onto the rails.

4. Secure the enclosure hardware to the rack.

– The unit attaches to the rack posts using the included screws and flange nuts.

– One screw each side, in the upper hole only.

4.3 Task 3: install disk drives

The CIP-5316W-00N and CIP-5424W-00N support SATA/SAS 3.5-inch hard disks.

4.3.1 Drive slot numbering

You can install any suitable disk drive into any slot in the enclosure.

5 6 7 8

9 10 11 12

13 14 15 16

2 3 4

Figure4.6: Drive slot numbering for 3U models

14 en | Setup tasks CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15 16

17 18 19 20

21 22 23 24

Figure4.7: Drive slot numbering for 4U models

Slot numbering is mapped in the web-based system Management GUI.

Insert all of the drive carriers into the enclosure to ensure proper airflow, even if you do not

populate all the carriers with disk drives.

Caution!

Swing open the drive carrier handle before you insert the drive carrier into the enclosure.

4.3.2 Remove the drive carrier

The drive carrier accommodates 3.5-inch drives.

Caution!

The CIP5000 models support hot-swapping disk drives.

To avoid hand contact with an electrical hazard, remove only one drive carrier at a time.

Push here when returning

or replacing the carrier into

an empty drive bay.

Pull here to release the carrier handle latch.

Then pull the carrier straight out by the handle.

Place your free hand under the carrier.

Do not drop the disk carrier, even if it is empty.

Figure4.8: Disk carrier with HDD installed (front view)

CIP5000 series storage Setup tasks | en 15

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

4.3.3 Install 3.5" disk drive in the carrier

Obey the following instructions to install 3.5” hard disk drives into the drive carriers.

1. Remove a disk drive carrier.

2. Carefully lay the disk drive into the drive carrier at the front, so that the screw holes on

the sides line up correctly with the power and data connectors facing away from the

carrier handle.

3. Insert the screws through the holes in the drive carrier and into the sides of the disk

drive.

– Install only the counter-sink screws supplied with the drive.

– Install four screws per drive.

– Snug each screw. Be careful not to over-tighten.

4. Reinstall the drive carrier into the enclosure.

Repeat steps 1 through 3 until all of your disk drives are installed.

Counter-sink screws

(two screws on each side)

Figure4.9: SATA disk drive mounted in a drive carrier

4.4 Task 4: establish I/O connections

This section describes how to establish a connection and login as the administrator to the

operating system.

There are two methods to establish the physical connections used for management of the

device:

– Connect directly to the server with the keyboard, mouse and monitor.

– Remotely through the network using the web-based Management GUI.

For the initial system configuration, obey the following instructions to connect the keyboard

and monitor so you can login to the operating system, then change the network settings for

the Ethernet ports to suit your network.

16 en | Setup tasks CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

Figure4.10: I/O ports on the rear panel

Connections for system management on rear panel:

1. VGA port

2. 1000BASE-T RJ-45 ports

3. USB 3.0 ports

4.4.1 Initial setup

Use a USB or PS/2 keyboard and a VGA monitor to establish a direction connection to the

Windows operating system.

All the I/O ports needed to do this are located on the rear panel. Connect a monitor, keyboard

and mouse to the appropriate port and you will be ready to login after the server has booted

up.

For instructions on how to login as administrator to the Windows OS user interface, refer to

Task 6: login to windows, page 19.

4.4.2 Network connection

There are two 1 Gb/s Ethernet RJ-45 ports on the rear panel for connection to an Ethernet

network. After logging into the Management GUI as the administrator, you can change the

network settings.

To connect the server to a local Ethernet for management:

1. Attach one end of an Ethernet cable to the network connector or standard NIC in the

Host PC. Attach the other end of the Ethernet cable to one of the ports on the standard

network switch.

2. Attach one end of an Ethernet cable to one of the ports on the standard network switch.

Attach the other end of the Ethernet cable to an Ethernet port (1000 BASE-T) on the back

of the server.

4.5 Task 5: connect power and power on

Insert one power cable into the power receptacle for each power supply unit (PSU) and

connect the each PSU to a suitable power source. The enclosure is equipped with two PSU

using an N+1 arrangement.

CIP5000 series storage Setup tasks | en 17

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

Notice!

The enclosure is equipped with LED indicators on the power supply units. Check the LEDs

after powering the devices on to make sure the cooling and power status for the power

module is normal.

4.5.1 Power on

With the power supplies connected, the system can now be powered on.

To power on the subsystem, press the power button on the left handle, then observe OPAS

LED on the left handle and LEDs on the right handle.

USB ports

OPAS LED

Power button

Figure4.11: Front panel components on the left handle

Power

System status

Global RAID status

Global HDD activity

(Reserved)

System heartbeat

Figure4.12: Front panel LEDs on the right handle

18 en | Setup tasks CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

4.5.2 Front panel LED behavior

The table below describes LED behavior when boot-up is finished and the system is operating

normally:

LED Description

Power Blue - System is powered on.

System status Green - System is normal.

Red - System trouble. Such as LD offline, fan malfunction, voltage

out of range, system temperature alert.

Red flash - HDD high temperature alert

Off steady - System is not ready.

Global RAID status Green - Status is normal.

Red - RAID volume is offline.

Orange - Critical state of any logical drive, or system is rebuilding.

Global HDD activity Blue flash - One or more drives are being accessed.

Blue - No drives are being accessed.

System heartbeat Blue flash - Firmware and software are operating normally.

OPAS USB Green - OPAS device (USB disk) is detected.

Green flash - OPAS operation is in progress.

Red - OPAS operation has failed.

4.5.3 Disk drive LEDs

Drive Status (OK)

Activity

Figure4.13: Hard disk drive carrier LEDs

There are two LEDs on each drive carrier. They report activity of the drive, and current

condition of the drive.

LED Description

Disk status Green - HDD is configured and working properly.

Red - HDD requires manual replacement.

Orange - Status notification of background RAID activity on this

articular HDD, and no user action is required.

Disk activity Blue flash - During drive activity.

4.5.4 PSU LEDs

After powering on the subsystem, check the LEDs on each power supply on the rear of the

device.

CIP5000 series storage Setup tasks | en 19

Bosch Security Systems B.V. Quick installation guide 2019-10 | V01 | F.01U.380.028

PSU 2

LED

PSU 1

LED

LED Description

PSU 1 or PSU 2 Green - normal operation

Red or Orange - a problem or unit failure

4.5.5 Rear panel LED behavior

When system boot-up is finished, use the LEDs on the controller on the rear of the device to

monitor various functions.

LED Description

Ethernet The LED locates on the upper left of each port:

Orange - Ethernet connected.

Orange flash - There is activity on the port.

Off steady - No connection has been established.

Link/Act and Speed The LED locates on the upper right of each port:

Orange - 100 Mbps

Green - 1000 Mbps

4.6 Task 6: login to windows

For Windows installations, once the system has booted up it is necessary to configure various

options to complete the OS setup.

You will be prompted to select a default language and other user interface preferences. Obey

the instructions on screen to complete your preferences selection and to create a user name

and password for the administrator. After completing these final tasks, the Windows desktop

appears.

There are two quick link icons, one for a web browser connection to CIP Management GUI,

and the other for the file that contains user documents.

4.7 Task 7: create logical drives

This section describes how to configure logical drives (LD) using the CIP Management GUI.

20 en | Setup tasks CIP5000 series storage

2019-10 | V01 | F.01U.380.028 Quick installation guide Bosch Security Systems B.V.

4.7.1 Log into management GUI

Double click the Management GUI link icon (WebPAM PROe) on the desktop to launch the

default browser and go to the login page.

When the log-in screen appears:

– Type administrator in the User Name field.

– Type password in the Password field.

– Click the Login button.

The User Name and Password are case sensitive

After logging in, the Management GUI opening screen appears. If there are any un-configured

physical drives in the enclosure, an Array Configuration menu also appears.

Notice!

Make a Bookmark (Firefox) or set a Favorite (Internet Explorer) of the Login Screen so you

can access it easily next time.

4.7.2 Choose a language

Management GUI displays in English and Simplified Chinese.

Choose your preferred language as one of following ways:

– Select the Language from the menu header in the Login screen.

– Click the language you prefer.

The Management GUI user interface displays in the chosen language.

4.7.3 Create logical drives

On a newly activated system, there are no disk arrays or logical drives.

To create a logical drive:

Page is loading ...

Bosch CIP‑5316W‑00N Quick Installation Manual

Brand: Bosch

Model: CIP‑5316W‑00N

Type: Quick Installation Manual

This manual is also suitable for

Download PDF

report

Bosch CIP‑5316W‑00N Quick Installation Manual

This manual is also suitable for

Bosch CIP‑5316W‑00N Quick Installation Manual

Related papers

Other documents