Carver 46 Assembly Instruction

Type
Assembly Instruction

This manual is also suitable for

Carver 46 is an advanced motor yacht setup that offers a range of capabilities to enhance your boating experience.

With its powerful propellers and drain plug, the Carver 46 ensures efficient and reliable propulsion. The exterior seating on the bridge and aft deck provides comfortable seating areas for relaxation and entertainment.

The bridge, featuring a wet bar, is designed for optimal control and convenience. It is equipped with 110 and 12 volt wires, making it easy to connect your electrical devices. The arch wire located in the port aft storage locker allows for seamless integration of additional electronics.

Carver 46 is an advanced motor yacht setup that offers a range of capabilities to enhance your boating experience.

With its powerful propellers and drain plug, the Carver 46 ensures efficient and reliable propulsion. The exterior seating on the bridge and aft deck provides comfortable seating areas for relaxation and entertainment.

The bridge, featuring a wet bar, is designed for optimal control and convenience. It is equipped with 110 and 12 volt wires, making it easy to connect your electrical devices. The arch wire located in the port aft storage locker allows for seamless integration of additional electronics.

Page 1 of 4
46 Motor Yacht Setup Part Number 9991600 3/07
46 Motor Yacht Setup
1. Install propellers and drain plug.
2. Remove tape and clean areas where the bridge will
set. Check for voids along the top of the windows.
Unfasten the wet bar and pull it back to install the
bridge.
3. Apply sealant (white Sikaflex supplied in Mac kit
#8105901) along the edge of the cabin top where
the bridge sets.
4. Apply 720 silicone sealant (white) around the stud
bolts.
Note: Refer to the attached pictures for sealant
placement. Apply the sealant just prior to setting
the bridge.
5. Position the bridge over the boat. e lifting
points for the bridge are between the two standoffs
on the forward bridge rails and on the aft bridge
rail (on the port side) and bow eye (on the starboard
side). Lower the bridge until it is 12" - 16"” above
the deck. Run all wires and hoses through the aft
end of the bridge through PVC pipe.
6. Lower the bridge onto the deck, making sure that
no wires or hoses get caught or pinched off.
7. With the bridge in place, attach it with the
fasteners supplied in the Mac kit. ere are 10
studs on the bridge (four forward under the helm,
one in each aft bridge corner, and two each on the
port and starboard sides). Refer to the drawing on
the next page for the location of these studs.
8. Install the port and starboard hardtop supports
and door frames (do not tighten them in place yet).
Use silicone when installing the bolts.
9. Lift hardtop by pick eyes. Set on wing door frame
and secure with supplied hardware.
10. Reinstall the wet bar wing, then install the wet
bar. Hook up the 110 volt wire, and the drain and
water lines under the wet bar.
11. Install the mast light on the arch.
12. Connect all dash wiring: Hook up the 110 and 12
volt wires under the starboard seat cushion and the
arch wire in the port aft storage locker.
13. Install the exterior seating on the bridge and aft
deck.
14. Cosmetically seal around the hardtop supports and
door frames.
Place Sealant where the black tape appears in the
following pictures.
Aft Starboard Corner
Starboard Side (from aft)
Page 2 of 4
46 Motor Yacht Setup Part Number 9991600 3/07
46 Motor Yacht Setup
Starboard Side (from forward)
Aft Port Corner
Port Side
Port Side
Starboard Side
Port Side
Page 3 of 4
46 Motor Yacht Setup Part Number 9991600 3/07
46 Motor Yacht Setup
Aft Port
Front
Front
Forward Stud Bolts
Page 4 of 4
46 Motor Yacht Setup Part Number 9991600 3/07
46 Motor Yacht Setup
Location of studs used to fasten bridge in place.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Carver 46 Assembly Instruction

Type
Assembly Instruction
This manual is also suitable for

Carver 46 is an advanced motor yacht setup that offers a range of capabilities to enhance your boating experience.

With its powerful propellers and drain plug, the Carver 46 ensures efficient and reliable propulsion. The exterior seating on the bridge and aft deck provides comfortable seating areas for relaxation and entertainment.

The bridge, featuring a wet bar, is designed for optimal control and convenience. It is equipped with 110 and 12 volt wires, making it easy to connect your electrical devices. The arch wire located in the port aft storage locker allows for seamless integration of additional electronics.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI