Riva RC5510 is a PTZ (pan-tilt-zoom) dome camera controller that provides comprehensive control over PTZ dome cameras. With its intuitive OSD menu, you can easily adjust various camera settings, including camera ID, home position, manual speed, and alarm configuration. Additionally, you can create and manage presets, auto-scan patterns, tours, privacy masks, and sector patrol routes. The device supports multiple communication protocols, including Pelco-D/-P, ensuring compatibility with a wide range of PTZ cameras.
Riva RC5510 is a PTZ (pan-tilt-zoom) dome camera controller that provides comprehensive control over PTZ dome cameras. With its intuitive OSD menu, you can easily adjust various camera settings, including camera ID, home position, manual speed, and alarm configuration. Additionally, you can create and manage presets, auto-scan patterns, tours, privacy masks, and sector patrol routes. The device supports multiple communication protocols, including Pelco-D/-P, ensuring compatibility with a wide range of PTZ cameras.
2
www.rivatech.de
Table of Contents
1. Menu and Setting ....................................................................... 5
1.1. OSD Menu Table ............................................................................ 5
1.2. How to Call OSD Menu ................................................................... 6
1.3. How to Operate the OSD Menu ........................................................ 7
2. Dome Setup .............................................................................. 8
2.1. DOME SET – CAMERA ID ................................................................ 8
2.2. DOME SET – HOME POS ................................................................. 8
2.3. DOME SET – MANUAL SPEED .......................................................... 9
2.4. DOME SET – AUTO FLIP .................................................................. 9
2.5. DOME SET – ZOOM SPEED .............................................................. 9
2.6. DOME SET – ALARM ...................................................................... 9
2.7. DOME SET - LANGUAGE .................................................................. 9
2.8. DOME SET - [NEXT PAGE]................................................................ 9
2.8.1 DOME SET - [NEXT PAGE] - SYSTEM LOCK .................................... 9
2.8.2. DOME SET - [NEXT PAGE] - [PASSWORD] .................................. 10
2.8.3. DOME SET - [NEXT PAGE] - [OSD DISPLAY]................................. 11
2.8.4. DOME SET - [NEXT PAGE] - [SYSTEM STATUS] ............................ 11
2.8.5. DOME SET - [NEXT PAGE] - [INITIALIZATION] ............................... 12
2.9. DOME SET - [NEXT PAGE] - SAVE AND EXIT...................................... 13
2.10. DOME SET - [NEXT PAGE] - EXIT ................................................... 13
3. CAMERA SET .......................................................................... 14
3.1. CAMERA SET - FLICKERLESS ......................................................... 14
3.2. CAMERA SET - MIRROR ................................................................ 14
3.3. CAMERA SET - APERTURE ............................................................ 14
3.4. CAMERA SET - D ZOOM ............................................................... 14
3.5. CAMERA SET - WB MODE ............................................................ 15
3.6. CAMERA SET - PIC FLIP ............................................................... 15
3
www.rivatech.de
3.7. CAMERA SET - BLC (Back Light Compensation) ................................. 15
3.8. CAMERA SET - D/N MODE ........................................................... 15
3.9. CAMERA SET – EXIT ..................................................................... 15
3.10. CAMERA SET – NEXT PAGE – SENS UP ......................................... 16
3.11. CAMERA SET – NEXT PAGE – AGC MODE ...................................... 16
3.12. CAMERA SET – NEXT PAGE – SSNR .............................................. 16
3.13. CAMERA SET – NEXT PAGE – COLOR ............................................ 16
3.14. CAMERA SET – NEXT PAGE – DIS MODE ....................................... 16
3.15. CAMERA SET – [PREVIOUS PAGE] ................................................. 16
4. PRESET SET ............................................................................ 17
4.1. PRESET - PRESET NO. .................................................................. 17
4.2. PRESET - PRESET ID ..................................................................... 17
4.3. PRESET - PAN: XXX.X TILT: XX.X ................................................... 17
4.4. PRESET - SAVE ............................................................................ 17
4.5. PRESET - EXIT ............................................................................. 17
5. AUTO SCAN SET ...................................................................... 18
5.2. AUTO SCAN - END ANGLE ............................................................. 18
5.3. AUTO SCAN - DIRECTION .............................................................. 18
5.4. AUTO SCAN - ENDLESS ................................................................ 18
5.5. AUTO SCAN - SPEED .................................................................... 18
5.6. AUTO SCAN - DWELL TIME ........................................................... 19
5.7. AUTO SCAN - SAVE AND EXIT ........................................................ 19
5.8. AUTO SCAN - EXIT ....................................................................... 19
6. TOUR SET ............................................................................... 20
6.1. TOUR SET - TOUR NO. .................................................................. 20
6.2. TOUR SET - TOUR TITLE ................................................................ 20
6.3. TOUR SET - TOUR STEP ................................................................ 20
6.4. TOUR SET - PRESET NO. ............................................................... 20
6.5. TOUR SET - DWELL TIME .............................................................. 20
6.6. TOUR SET - SPEED ....................................................................... 21
6.7. TOUR SET - SAVE ......................................................................... 21
4
www.rivatech.de
6.8. TOUR SET - EXIT .......................................................................... 21
7. TOUR SET ............................................................................... 22
7.1. PRIVACY SET - PRIVACY NO. ......................................................... 22
7.2. PRIVACY SET - DISPLAY ................................................................ 22
7.3. PRIVACY SET - ACTION (MOVE / ADJUST) ....................................... 22
7.4. PRIVACY SET - SAVE .................................................................... 23
7.5. PRIVACY SET - EXIT ...................................................................... 23
8. PATTERN SET .......................................................................... 23
8.1. PATTERN SET - PATT NO. ............................................................. 23
8.2. PATTERN SET - PATT TITLE ........................................................... 23
8.3. PATTERN SET - DATA FILL ............................................................ 23
8.4. PATTERN SET - SAVE ................................................................... 24
8.5. PATTERN SET - EXIT ..................................................................... 24
9. ALARM SET ............................................................................ 24
9.1. ALARM SET - ALARM NO. ............................................................. 24
9.2. ALARM SET - ALARM INPUT ......................................................... 24
9.3. ALARM SET - ALARM ACT ............................................................ 24
9.4. ALARM SET - SAVE ...................................................................... 24
9.5. ALARM SET - EXIT ....................................................................... 25
10. SECTOR SET .......................................................................... 25
10.1. SECTOR SET - SECTOR NO. .......................................................... 25
10.2. SECTOR SET - SECTOR ID ............................................................ 25
10.3. SECTOR SET - SECTOR START ...................................................... 26
10.4. SECTOR SET - SECTOR END ......................................................... 26
10.5. SECTOR SET - SAVE ................................................................... 26
10.6. SECTOR SET - EXIT ..................................................................... 26
11. EXIT ..................................................................................... 26
REVISION HISTORY ....................................................................... 26
5
www.rivatech.de
1. Menu and Setting
1.1. OSD Menu Table
MAIN MENU
DOME SETUP
CAMERA SET
PRESET
AUTO SCAN
TOUR
PRAVACY
PATTERN
ALARM
SECTOR
EXIT
CAMERA SET
FLICKER : OFF/ON
MIRROR : OFF/ON
APERTURE : 16
D ZOOM : OFF/ON
WB MODE : ATW MODE
PIC FLIP : OFF
BLC : OFF [BLC]
D/N MODE : AUTO
MODE
[NEXT PAGE]
EXIT
PRESET SET
PRESET NO : 001
PRESET ID : PRESET01□□□□□□□□□
PAN:xxx.x TILT:yy.y
SAVE
EXIT
AUTO SCAN SET
START ANGLE : xxx.x yy.y
END ANGLE : xxx.x yy.y
DIRECTION : CW
ENDLESS : OFF
SPEED : 10 °/S
DWELL TIME : 03
SAVE AND EXIT
EXIT
SECTOR SET
SECTOR NO : 01
SECTOR ID : SECTOR01□□□
SECTOR START: xxx.x yy.y
SECTOR END : xxx.x yyy,y
SAVE
EXIT
PATTERN SET
PATT NO. : 01
PATT TITLE PATTERN01□□□
DATA FILL : 000%
SAVE
EXIT
ALARM SET
ALARM NO. : 01
ALARM INPUT : NO
ALARM ACT : 001
SAVE
EXIT
PRIVACY SET
PRIVACY NO. : 01
DISPLAY : OFF
ACTION : MOVE
SAVE
EXIT
TOUR SET
TOUR NO. : 01
TOUR TITLE : TOUR01□□□□□□
TOUR STEP : 01
PRESET NO : 001
DWELL TIME : 03
SPEED : 250°/S
SAVE AND EXIT
EXIT
DOME SET
SYSTEM LOCK : OFF
[PASS WORD]
[OSD DISPLAY]
[SYSTEM STATUS]
[INITIALIZATION]
[PREVIOUS PAGE]
[INITIALIZATION]
[TOUR CLEAR]
[PRESET CLEAR]
[SECTOR CLEAR]
[PRIVACY CLEAR]
[PATTERN CLEAR]
[LOAD OPTIMIZED DEFAULT
[REVIOUS PAGE]
[SYSTEM STATUS]
PROTOCOL : PELCO D,P
BAUD RATE : 2400BPS
FIRMWARE VER .: 1.00a
UPGRADED DATE : 15.04.11
CAMERA MODULE : SCM2120
[PREVIOUS PAGE]
OSD DISPLAY
CAMERA ID: OFF/ON
PRESET ID: OFF/ON
SECTOR ID: OFF ON
COORDINATE:ON/OFF
[PREVIOUS PAGE]
DOME SET
CAMERA ID : CAM1□□□□□□□□□□□□
HOME POSITION : OFF
MANUAL SPEED : 100°/S
AUTO FLIP : OFF
ZOOM SPEED : FAST
ALARM : DISABLE
LANGUAGE : ENGLISH
[NEXT PAGE]
SAVE AND EXIT
EXIT
CAMERA SET
SENSE UP : X2
AGC MODE : MIDDLE
SSNR MODE : MIDDLE
COLOR : 050
DIS MODE : OFF
[PREVIOUS PAGE]
6
www.rivatech.de
1.2. How to Call OSD Menu
1. Click the PTZ button on the main view page of RC5510.
2. Press the arrow on the bottom of the PTZ Control box to expand the menu.
3. Click the Menu Off button to change the setting as Menu On.
4. Then, you can see the MAIN MENU is displayed on the VIEW as below.
1
2
3
2
7
www.rivatech.de
1.3. How to Operate the OSD Menu
1. Select a menu item using the Up () or Down () button on the PTZ Control
box.
2. To see the sub menus, click the Right () button on the desired menu.
3. Use the Up () or Down () button to go to the desired option for setting, and
finish the setting by using the Left () or Right () button.
4. To save the setting, select SAVE or SAVE AND EXIT and click the Right ()
button.
5. To exit the OSD menu, go to MAIN MENU, select EXIT, and then press the
Right () button.
MAIN MENU
DOME SETUP
CAMERA SET
PRESET
AUTO SCAN
TOUR
PRIVICY
PATTERN
ALARM
SECTOR
EXIT
8
www.rivatech.de
2. Dome Setup
To enter the Dome Setup menu, select right direction when the cursor is on the Dome
Setup menu.
2.1. DOME SET – CAMERA ID
To set the camera name, select DOEM SET > CMERA ID and select a title of up to 16
characters using left or right direction keys or joystick.
Press ZOOM TELE button to move to the next character from left to right direction
and
ZOOM WIDE button to move to the next character from right to left direction.
2.2. DOME SET – HOME POS
HOME POS has the ability for implementing that a user has registered functions
(PRESET / TOUR / PATTER / SCAN) if it lasts the situation without handle of camera.
You can set up the time [15~90sec] with operating for PAN LEFT/RIGHT of Joystick,
in case of using the function of HOME POSITION.
If it does not work until it reaches the time that has been set up, the function set-up
works.
If you press the key for FOCUS FAR for the time set-up, it will display ■ mark on the
menu. In that situation you can exchange the function for [PRESET/TOUR/PATTERN]
you want by operating the key for PAN LEFT/RIGHT of Joystick.
DOME SET
CAMERA ID : CAM1
HOME POS : OFF
MANUAL SPEED : 100°/S
AUTO FLIP : OFF
ZOOM SPEED : FAST
ALARM : DISABLE
LANGUAGE : ENGLISH
[NEXT PAGE]
SAVE AND EXIT
EXIT
9
www.rivatech.de
2.3. DOME SET – MANUAL SPEED
The manual speed of Pan/Tilt is selectable from 100°/sec up to 150°/sec.
The default setting is 100°/sec.
2.4. DOME SET – AUTO FLIP
Auto Flip enables the dome to automatically do a 180° turn when the tilt bottom point
is reached. The default setting is OFF.
2.5. DOME SET – ZOOM SPEED
Zoom speeds are selectable as FAST or SLOW mode. The default setting is FAST.
2.6. DOME SET – ALARM
You must enable the alarms for them to operate. The default setting is DISABLED.
2.7. DOME SET - LANGUAGE
Multiple languages are selectable (English, German, Dutch, Danish, French).
The default setting is ENGLISH.
2.8. DOME SET - [NEXT PAGE]
2.8.1 DOME SET - [NEXT PAGE] - SYSTEM LOCK
DOME SET
SYSTEM LOCK: : OFF
[PASS WORD]
[OSD DISPLAY]
[SYSTEM STATUS]
[INITIALIZATION]
[PREVIOUS PAGE]
10
www.rivatech.de
All stored dome settings can be password protected to prevent unauthorized changes.
In order to enter [PASS WORD] page, the system lock status must firstly be set as ON.
The default setting is OFF.
2.8.2. DOME SET - [NEXT PAGE] - [PASSWORD]
To enter this page to set a password, move joystick or pan key in the right direction.
The password must be set by preset number from 001 to 255 (Default 99).
Enter any number from 001~255 on the password blank area and again for
confirmation on blank area. Then “CONFIRMED” is displayed on the monitor and the
menu will go back to the previous page automatically.
If you press an incorrect number between PASSWORD and CONFIRM, “NOT CORRECT”
is displayed on the monitor.
* When a password has been set, the operator must enter the correct password in
order to enter OSD MAIN MENU, or to change any of the domes configuration data.
* If you set a password you must ensure that it does not get lost. If this happens the
dome must be returned for workshop repair.
ENTER PASSWORD
BY ENTERING PRESET CODE
PASSWORD ***
CONFIRM ***NOT CORRECT
ENTER PASSWORD
BY ENTERING PRESET CODE
PASSWORD ***
CONFIRM ***CONFIRMED
<CONFIRMED>
<CANCELLED>
ENTER PASSWORD
BY ENTERING PRESET CODE
PASSWORD ***
CONFIRM ***
11
www.rivatech.de
2.8.3. DOME SET - [NEXT PAGE] - [OSD DISPLAY]
The camera ID setting defines whether the camera OSD display is displayed or
switched off.
2.8.4. DOME SET - [NEXT PAGE] - [SYSTEM STATUS]
This page shows the information of this camera.
- Protocol and baud rate are shown according to the dip switch setting
(Refer to page 36, 37)
- Firmware version and upgraded date will be changed if the dome has been
upgraded.
- The camera module type is stated as follows.
SYSTEM STATUS
PROTOCOL : PELCO D, P
BAUD RATE : 2400 BPS
FIRMWARE VER. : X.XX
UPGRADED DATE :
DD.MM.YY
CAMERA MODULE :
XXXXXXXX
[PREVIOUS PAGE]
OSD DISPLAY
CAMERA ID : OFF
PRESET ID : OFF
SECTOR ID : OFF
COORDINATE : ON
[PREVIOUS PAGE]
12
www.rivatech.de
2.8.5. DOME SET - [NEXT PAGE] - [INITIALIZATION]
To clear the current settings select the item that you wish to reset back to factory
defaults.
- To clear the memorized data, move the joystick or pan right key until the
cursor is on the required item.
Press FOCUS NEAR button when the cursor is at YES in order to clear memorized
data. Then each item such as tour, preset, and sector will flicker for about 2~3
seconds. After this process, the menu is returned to the previous page.
* Use the above method for [PRESET CLEAR], [SECTOR CLEAR], [PRIVACY CLEAR],
[PATTERN CLEAR], [TOUR CLEAR].
TOUR CLEAR
ARE YOU SURE? YES NO
TOUR CLEAR
INITIALIZATION
[TOUR CLEAR]
[PRESET CLEAR]
[SECTOR CLEAR]
[PRIVACY CLEAR]
[PATTERN CLEAR]
[LOAD OPTIMIZED DEFAULT]
[PREVIOUS PAGE]
13
www.rivatech.de
- To clear all data and return to factory defaults, move the joystick right or press
the pan
right key to when the cursor is at [LOAD OPTIMIZED DEFAULT] to enter the
next page.
- Move the joystick or the pan right keys so that the cursor is over YES, then
press the
FOCUS NEAR button.
“ALL DATA INITIALIZING” is then displayed for about 5~7 seconds and then the menu
is returned to the previous page automatically.
2.9. DOME SET - [NEXT PAGE] - SAVE AND EXIT
To save the memorized data and escape from this page, move the joystick right or
press the pan right key when cursor is at SAVE AND EXIT.
2.10. DOME SET - [NEXT PAGE] - EXIT
In order to escape from this page, move the joystick right or press the pan right key
when the cursor is at EXIT.
LOAD OPTIMIZED
DEFAULT
ARE YOU SURE? YES NO
ALL DATA INITIALIZING
14
www.rivatech.de
3. CAMERA SET
3.1. CAMERA SET - FLICKERLESS
The flicker less feature has options of 50Hz and 60Hz.
The default setting is OFF (NTSC: 60Hz / PAL: 50Hz). The flicker less mode only
needs to be set when there is a mismatch between the power frequency and camera
sync rate.
The default setting is OFF.
3.2. CAMERA SET - MIRROR
This feature literally swaps the image left and right as if looking into a mirror.
The default setting is OFF.
3.3. CAMERA SET - APERTURE
Aperture correction enhances the picture details and sharpness by increasing the gain
of the camera. Increase the value to sharpen the image, decrease to soften it. The
default setting is 10. (the aperture level is from 01 ~ 15)
3.4. CAMERA SET - D ZOOM
If enabled digital zoom is applied when the zoom lens has reached its maximum optical
zoom in capability. The default setting is OFF.
CAMERA SET
FLICKER : OFF
MIRROR : OFF
APERTURE : 10
D ZOOM : OFF
WB MODE : AWB
MODE
PIC FLIP : OFF
BLC : OFF [BLC]
D/N MODE : AUTO
[NEXT PAGE]
EXIT
CAMERA SET
SENS UP : X2
AGC MODE : MIDDLE
SSNR MODE : MIDDLE
COLOR : 050
DIS MODE : OFF
[PREVIOUS PAGE]
15
www.rivatech.de
3.5. CAMERA SET - WB MODE
White balance functions ha 4 modes and may need to be changed depending on the
situation.
● AWB Mode – 3,200°K to 6, 000°K (Default)
● Indoor – up to 3,200°K
● Outdoor – up to 5,800°K
● ATW Mode - 2,000°K to 10, 000°K
3.6. CAMERA SET - PIC FLIP
The picture flip feature switches the top and bottom of the image.
The default setting is OFF.
3.7. CAMERA SET - BLC (Back Light Compensation)
In case of BLC, you can select the [BLC/[HLC]/[SSDR] function.
If you prefer to make BLC function exchange into [BLC]/[HLC]/[SSDR], you've got to
press
key for <FOCUS FAR> in situation operated into [ON].
So you can get a new menu for setting up MODE or Option like below.
BLC : That's the function for treat exposure In case of lack of exposure of
section that you
watch that there is a source of lights within the section looked.
HLC : It's used to recognize subject exactly when lack of exposure by strong
source of lights
SSDR :That's the function for treat into the right exposure state controlling both
of bright and dark section.
3.8. CAMERA SET - D/N MODE
The dome camera can operate in day /night mode and will switch depending on
lighting conditions. Alternatively it can be forced into color only mode.
The default setting is AUTO MODE.
3.9. CAMERA SET – EXIT
In order to escape this page, move the joystick right or press the pan right key when
the cursor is at EXIT.
16
www.rivatech.de
3.10. CAMERA SET – NEXT PAGE – SENS UP
Sens increases the CCD sensitivity by electrically extending the camera’s exposure
time.
3.11. CAMERA SET – NEXT PAGE – AGC MODE
AGC(Auto Gain Control)is a function that automatically controls image signal level on
electronic circuit and keeps the level consistent by amplifying the image signal level in a
low light environment to prevent a saturation image. You can optimize image
performance in variable light environments by operating Auto Gain Control function.
The default setting is MIDDLE.
3.12. CAMERA SET – NEXT PAGE – SSNR
This function reduces the background noise in a low luminance environment.
The default setting is MIDDLE.
3.13. CAMERA SET – NEXT PAGE – COLOR
Color control is available. Color value ranges from 0 to 100
When the value gets higher the color tone is stronger.
When the value gets lower the video get closer to black and white.
The default setting is 50.
3.14. CAMERA SET – NEXT PAGE – DIS MODE
DIS function compensates the vibration of camera.
The default setting is OFF.
3.15. CAMERA SET – [PREVIOUS PAGE]
To move previous page, move the joystick right or press the pan right key.
17
www.rivatech.de
4. PRESET SET
To enter PRESET SET, move joystick to the right direction.
4.1. PRESET - PRESET NO.
Up to 165 preset positions are available. Use the joystick or pan left/right keys to
select the number.
4.2. PRESET - PRESET ID
To create preset titles use the joystick or pan left/right keys to navigate the menu.
The ZOOM TELE button moves to the next character from left to right and ZOOM
WIDE button moves to the next character from right to left (Space displays when □
appears).
4.3. PRESET - PAN: XXX.X TILT: XX.X
Press FOCUS FAR button in order to set preset position then, use the joystick or pan
left/right keys to the position where memorized preset number is needed. Then press
FOCUS FAR button again after setting a preset location.
4.4. PRESET - SAVE
Move the joystick right or press the pan right key when the cursor is at SAVE and then
the cursor will be located on Preset ID for the continuous preset No. setting.
4.5. PRESET - EXIT
To escape this page, move the joystick right or press the pan right button.
PRESET SET
PRESET NO :001
PRESET ID :PRESET001-------
PAN :XXX.XX TILT : XXX.XX
SAVE
EXIT
18
www.rivatech.de
5. AUTO SCAN SET
5.1. AUTO SCAN - START ANGLE
To set the start position, press FOCUS FAR button then move the dome to the
required start position. Press FOCUS FAR button again is to escape.
5.2. AUTO SCAN - END ANGLE
To set the end position, press FOCUS FAR button then move the dome to the
required end position. Press FOCUS FAR button again is to escape.
5.3. AUTO SCAN - DIRECTION
Auto Scan directions are available as CW or CCW.
● CW: Clock wise direction (Default)
● CCW: Count Clock Wise Direction
5.4. AUTO SCAN - ENDLESS
Auto Scan can be set to endless rotation by enabling the endless option.
The default setting is OFF.
5.5. AUTO SCAN - SPEED
Auto scan speed can be programmed from 05°/S up to 35°/S. The default setting is
10°/S.
AUTO SCAN SET
START ANGLE : xxx.x.yy.y
END ANGLE : xxx.x.yy.y
DIRECTION : CW
ENDLESS : OFF
SPEED : 10°/S
DWELL TIME : 03
SAVE AND EXIT
EXIT
19
www.rivatech.de
5.6. AUTO SCAN - DWELL TIME
The dwell time at the start and end points can be programmed from 1 second to 30
seconds. The default setting is 03 seconds.
5.7. AUTO SCAN - SAVE AND EXIT
To save the memorized data and escape this page, move the joystick right or press
the pan
right key when the cursor is at SAVE AND EXIT.
5.8. AUTO SCAN - EXIT
To escape this page, move the joystick right or press the pan right key.
20
www.rivatech.de
6. TOUR SET
8 Programmable tours can be set and each tour can have up to 64 preset steps.
6.1. TOUR SET - TOUR NO.
Up to 8 group tours can be programmed.
6.2. TOUR SET - TOUR TITLE
To set a tour title, use the joystick left/right or pan left/right keys.
Each title can have up to 16 characters.
Press ZOOM TELE button to move the next character from left to the right and
ZOOM WIDE button to move the next character from right to left (Space displays when
□ appears) The tour title is not displayed on the monitor and is only for the reference
of user.
6.3. TOUR SET - TOUR STEP
Each tour group consists of up to 60 preset steps with different dwell time and speed.
It is possible to match any preset # for any tour step.
6.4. TOUR SET - PRESET NO.
For each tour step it is possible to select any preset number up to 64.
The default setting is BLK.
6.5. TOUR SET - DWELL TIME
Dwell time can be programmed from 1-99 seconds. The default setting is 03 seconds.
TOUR SET
TOUR NO : 01
TOUR TITLE : TOUR01
TOUR STEP : 01
PRESET NO. : 01
DWELL TIME : 03
SPEED : 200º/S
SAVE
EXIT
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Riva RC5510 is a PTZ (pan-tilt-zoom) dome camera controller that provides comprehensive control over PTZ dome cameras. With its intuitive OSD menu, you can easily adjust various camera settings, including camera ID, home position, manual speed, and alarm configuration. Additionally, you can create and manage presets, auto-scan patterns, tours, privacy masks, and sector patrol routes. The device supports multiple communication protocols, including Pelco-D/-P, ensuring compatibility with a wide range of PTZ cameras.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Optiview Mini Speed Dome Camera User manual
-
Vivotek KA-SD10 User manual
-
Santec VDC-610ID User manual
-
-
Eneo Fastrax III EDC-3182 Specification
-
Costar CDC3600X User manual
-
Intellisystem ThermalTronix TT-L-BFTC Series User manual
-
Vista VP-HDA30-PM Installation guide
-
-
Vista CCTV VP-HDA30IR-PM Installation guide
