Page is loading ...
Wattstopper
®
Wireless Lighting Control System, EORS Series Wireless Remote
Switch, EOHR Series Handheld Remote
Système de contrôle de l’éclairage sans fil, Interrupteur à distance sans fil de
la série EORS, Dispositif manuel de commande à distance de la série EOHR
Sistema de control de iluminación inalámbrica, Interruptor remoto
inalámbrico serie EORS, Remoto manual serie EOHR
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24269 – 08/18 rev. 1
Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: EORS-101/102, EOHR-101/102
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
SPECIFICATIONS
Input Voltage: ....................... Self-powered when the switch is pressed
Connection to Wireless Network: ...........................................................
Sends signals to Wall Switches via Radio Frequency
Environment .......................................................... For Indoor Use Only
Operating Temperature ..............................32° to 131°F (0° to 55°C)
Storage Temperature ............................... 23° to 176°F (-5° to 80°C)
Relative Humidity ....................................5 to 95% (non condensing)
Patent Pending
EORS-101
legrand
EORS-102
legrand
EOHR-101
legrand
EOHR-102
legrand
MOUNTING AND PLACEMENT
The EORS and EOHR are low profile wireless self-powered remote switches that can be placed anywhere within range of the system,
up to 150ft in an open space.
EORS Remote Switch
Secure the EORS Remote Switch to the wall
plate and junction box using two machine screws
(included). Please, do not force or overtorque unit
with torque screw driver. To do so may damage the
unit. < 8 in-lb of torque is adequate to secure unit.
Align the sensor in the J-Box so that the mounting
screw tabs on the J-Box match the key holes on
the sensor’s rear housing.
EORS-101
Junction box
Wall plate
legrand
EOHR Handheld Remote
The EOHR can be used as a handheld remote or mounted to a glass wall using
the double-back foam tape on the back of mounting bracket as shown. It can
also be mounted to a hard wall using two screws and the mounting bracket
provided.
Mounting to Hard Wall
1. Drill holes in wall
using the two holes
on the mounting
bracket as a
template.
2. Secure the
mounting bracket to
the wall using two
machine screws
(included).
3. When finished
slide EOHR onto
mounting bracket.
Double-backed
foam tape
Wall Mount
EOHR-102
Use the double-backed
foam tape on the back
of EOHR mounting bracket
to mount to a glass wall
Mounting
Bracket
Slide EOHR onto
mounting bracket
to secure
Use two screws to mount
the EOHR-10x to a hard wall
using the mounting bracket
legrand
POWER AND OPERATION
The EORS-10x Wireless Remote Switch and
EORS-10x Handheld Remote are self-powered by
harvesting the kinetic impulse of the physical push
of the button.
Once a device is paired with the remote, the
EORS and EOHR use radio frequencies to
transmit signals to the wireless system. To turn
load(s) ON/OFF, press the paddle button on the
EORS-10x or EOHR-10x.
EOHR-101
On/Off
button
EOHR-102
EORS-102
EORS-101
Press left or right
button to toggle
loads On/Off
Press left or right
button to toggle
loads On/Off
On/Off
button
On/Off
button(s)
On/Off
button(s)
Press button to
turn loads On/Off
Press button to
turn loads On/Off
2
PAIRING OF REMOTE SWITCH TO WALL SWITCH RECEIVER LOAD(S)
Pairing of the remote switch or handheld remote is simply done by entering pairing mode at the wall switch receiver (EOSW-1x1 or
EOSW-1x2) and pressing the Pairing button “P” on each device for 3 seconds.
Step 1 Enter Pairing Mode
Press and Hold “Pairing” Button “P” on Receiver for 3 Seconds then release:
• Pairing LED on the EOSW switch begins to blink rapidly (2x/second). This confirms that the Receiver is now in pairing mode. For
EOSW-101/ EOSW-111
• Load 1 turns ON and is ready to be paired
• Load status button LED is Solid ON. For EOSW-102/ EOSW-112
• Load 1 & 2 turn ON and are ready to be paired
• Load status button 1 & 2 LED are Solid ON
Step 2 Selecting a Specic Load to Pair (EOSW-102)
*By default, both loads turn ON at the same time in Pairing Mode. If both loads are to be controlled by the Remote Switch than skip this step.
Tap the “Pairing” Button “P” once while in pairing mode:
• Load 2 turns OFF and Load 1remains ON
• Load 1 is now active and ready to be paired to selected transmitters
• Load 1 LED is Solid ON
Tap the “Pairing” Button “P” once again while in pairing mode:
• Load 1 turns OFF and Load 2 turns ON
• Load 2 is now active and ready to be paired to selected transmitters
• Load 2 LED is Solid ON
Tap the “Pairing” Button “P” a third time while in pairing mode:
• Load 1 and Load 2 turn ON again, indicating both loads are ready to be paired.
EOSW-102
“Load 1 Status”
Blue LED OFF
Pairing
Button
“Load 2 Status”
Blue LED On
legrand
legrand
EOSW-102
“Load 1 Status
”
Blue LED ON
Pairing
Button
legrand
legrand
“Load Status
”
Blue LED
Pairing
Button
EOSW-101
legrand
legrand
EOSW-102
“Load Status
”
Blue LED
Pairing
Button
legrand
legrand
3
Step 3 Pair Remote Switch (EORS or EOHR) to Receiver
Tap the button on the Remote Switch or Handheld Remote as follows:
For EORS-101 or EOHR-101 tap button 3 times
For EORS-102 or EOHR-102 tap the desired button 3 times to pair that button to the load that is ON. Once paired the switch will exit
pairing mode. Repeat steps 1 through 3 to pair the next button.
NOTE: If only one button is to be paired to 1 load, only press the desired button 3 times. The selected load(s) status LED on the
receiver will flash OFF/ON for visual pairing confirmation.
You can have a load bound to one button, both buttons or no buttons.
Step 4 Exit “Pairing” Mode on Receiver
Once a device is paired with the receiver the receiver will automatically exit “pairing” mode.
• To manually exit pairing mode, press and hold the “Pairing” button “P” on the receiver until the blue LED turns off, approximately 3
seconds.
• The device will also exit pairing mode if no device is paired to it within 30 seconds.
UNPAIRING REMOTE BUTTONS FROM A RECEIVER (SWITCH)
If using single button remote EORS-101 or EOHR-101
Press and hold the Paring Mode button “P” for approximately three seconds then release. The Green LED
will start flashing confirming you are in Pairing mode. The load will turn ON if previously OFF.
• Tap the remote button 3 times to unpair the remote from the reciever switch.
• The load will temporarily turn OFF and ON confirming the message was received.
• The green Pairing LED on the switch will stop flashing and exit pairing mode.
• The remote button should no longer control the load.
• Repeat steps above to unpair additional remotes.
If using a two button remote EORS-102 or EOHR-102
* It is recommended that you first confirm how the buttons are paired to the receiver switch. Using the
remote, press each button to turn the loads ON and OFF in order to see which button is paired to each
load.*
• Press and hold the Paring Mode Button “P” for approximately three seconds then release. The
Green pairing “P” LED will start flashing confirming you are in Pairing mode. The loads will turn ON if
previously OFF.
Using the “Pairing” Button “P” on the Receiver, select the load(s) to unpair
• Pressing the Pairing button “P” once will turn Load 2 OFF and Load 1 will remain ON.
• Pressing the Pairing button “P” again will turn Load 1 OFF and Load 2 will turn ON.
• Pressing the Pairing button “P” again will turn both loads ON.
• Use this method to select which load or loads to unpair.
EORS-101 Series EOHR-101 Series
legrand
legrand
EORS-102 Series EOHR-102 Series
legrand legrand
“Load Status
”
Blue LED
Pairing
Button
EOSW-101
legrand
legrand
EOSW-102
“Load 1 Status
”
Blue LED ON
Pairing
Button
legrand
legrand
4
To unpair the selected load(s)
• Tap the remote button 3 times to unpair the remote button from the switch.
• The load(s) will temporarily turn OFF and ON confirming the message was received.
• The green LED on the switch will stop flashing and exit pairing mode.
• The remote button should no longer control the load(s).
• Repeat steps above to unpair another button.
TO “UNPAIR” ALL CONNECTED DEVICES
Press and hold the Wall Switch Pairing button “P” for about 10 seconds, until all LEDs on the units start flashing all together.
TROUBLESHOOTING
Does the system work more reliably at close range (without obstructions)?
In an indoor environment, the wireless controls have a typical range of 30-150 feet. If there are obstructions and/or noise interference
the range will be less than the typical range.
Consider Factors Affecting the Environment:
The range can be reduced by metal objects (metal decreases the effectiveness of RF transmission). Switches also go into a reduced
range mode when in programming (under 15 feet)
• Identify nearby metal, concrete and other objects possibly affecting signal strength
• If possible, try relocating the device (even slightly) away from obstructions to improve the system performance.
Consider Factors Affecting the Environment:
• Device placement
• Obstructions (metal, concrete, other construction materials)
• Interference
Does the system work better at certain times of the day?
• Look for pieces of equipment that may affect wireless performance when they are ON
• Noise interference can be either line noise (from motors) or Radio Frequency (RF)
Product Performance:
• To isolate any variation in product performance replace one piece of hardware at a time
Load does not turn ON or OFF:
• If load does not shut off automatically, enter configuration mode to check settings for the load (if in manual mode switch to auto
mode). If you cannot switch then sensor is not paired to load.
• If load does not turn on/off from remote switch, check pairing of the switch to the load. (See pairing devices.)
CONTAINS FCC ID: SZV-PTM210U and IC: 5713A-PTM210U
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
/
