2315 Series
Panel Door Magnetic Contact
Models: 2315A, 2317A
Installation Instructions
Mounting
Caution: Locate the magnet away from manual
handles and latches to prevent it from being used
as a foothold or handle to close the door.
1. Slide the slot of the switch over the beveled-edge of
the L-bracket and snap it tightly into place as shown in
Figure 1. Screw down firmly.
Figure 4
2. Align the magnet with the switch and use screws to
attach it to the door as shown in Figure 2. The switch
and magnet must be aligned within 1/2 inch of each
other to prevent false alarms.
3. Connect the switch wires to the alarm system and test to
verify proper operation.
Important: The contact should be mounted at
least 13 inches from the floor. If other track-
mounted devices interfere, mount the switch under
them.
Figure 1
Figure 2
Optional: Use the existing roller-track bolts to
mount the switch without using the L-Bracket as
shown in Figure 3.
Figure 3
The magnet can be attached at
two different elevations from
the door.
Fits standard 2” roller-tracks for
sectional/panel overhead
doors.
elevation 1
elevation 2
1/4 to 1/2” spacing
Ordering Information
General
The contact shall be a hermetically sealed reed switch nomi-
nally 3.07” H x 1.80” W x 2.60” D with actuating magnet.
Contact and magnet shall be in extruded aluminum type
housing. Contact shall be sealed in GE Interlogix exclusive
polyurethane potting compound. Mounting bracket shall be
furnished with contact. Contacts shall be specified as GE
Interlogix part numbers 2315A and 2317A. Contact is de-
signed for installation on metal overhead door tracks.
USA Specifications
Form A (2315A)
Voltage 100V AC/DC max.
Current 0.5 A max.
Power 7.5 W max.
Form C (2317A)
Voltage 30V AC/DC max.
Current 0.25 A max.
Power 3.0 W max.
Canadian Specifications
Form A (2315A), Form C (2317A)
Voltage 30VDC max.
Current 50mA max.
European Union Specifications
Form A (2315A)
Voltage 48V AC/DC max.
Current 0.5A max.
Dimensions Specifications
*Gap distances are nominal make distance ±20%. Gap specifications are for switch to make. Break distance is approximately 1.1
to 1.5 times make.
Fits 1.5” (3.8cm)
to 2.4” (6.1cm)
3.07”
7.8cm
2.6”
6.6cm
1.8”
4.6cm
2.0”
5.1cm
1.88”
4.8cm
0.85”
2.2cm
2.16”
5.5cm
3.1”
7.9cm
1.7”
4.3cm
3.51”
8.9cm
2.51”
6.4cm
WARNING: Each electrical rating is an
individual maximum and cannot be
exceeded!
www.GE-InterlogixSecurity.com
1030554 Rev B 09/03
12345 SW Leveton Drive
Tualatin, OR 97062
Ph
USA & Canada: 800-336-4206
Technical Service: 800-454-2363
FaxBack: 800-483-2495
GE Interlogix
2266 Second Street North
North St. Paul, MN 55109
Phone: 651-777-2690
Made in Taiwan
Model Loop Type Electrical Gap Distance Lead Type Listing
Number Configuration (Make)*
2315A-L Closed NO Up to 3” 2’ stainless steel armored cable C UL-US
2317A-L Open or closed SPDT Up to 3” 2’ stainless steel armored cable C UL-US
Lead Color Function
Black Common
White Closed Loop (N.O.)
Red Open Loop (N.C.)
Lead Functions
Form C (2317A)
-
1
-
2
Interlogix 2315 / 2317 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Interlogix 1038T Series Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Potter ODC-56 Series Overhead Door Contact Owner's manual
-
EDWARDS 2302 Installation guide
-
YAESU FT-230R User manual
-
Grizzly 9962ZX User manual
-
AMADA HOMEFURNISHING AMLS01 User manual
-
-
-
MTD 146-960A User manual
-
-
