Interlogix 2750 Series Installation guide

Brand: Interlogix

Model: 2750 Series

Type: Installation guide

Interlogix 2750 Series is a switch designed for use with metal doors, featuring three independent form C triple-biased reed contacts wired in SPDT configuration (2757) or six independent form C triple-biased reed contacts wired in DPDT configuration (2757D). Both models have Alnico VIII and Arnox V magnets and conform to the specifications for Class IV Preadjusted Balanced Magnetic Contacts. They have an actuating gap distance (make) of up to 0.4" (1.031cm) and fit into a standard ANSI cutout for mortise installation 1.25" (3.18cm) x 4.875" (12.38cm). The 2757 has a depth of 1.25" (3.

2750 Series

Models: 2757, 2757D

Installation Instructions

2757

Closedloop

(white)

Openloop

(red)

Commonno label

(black)

Supervisedloop

(brown)

Closedloop

(white)

Openloop

(red)

Commonno label

(black)

Supervisedloop

(green)

Supervisedloop

(brown)

Closedloop

(yellow)

Openloop

(orange)

Commonnolabel

(blue)

Supervisedloop

(green)

2757D

.875"

2.22cm

4.875"

12.38cm

Magnet

1.25"

3.18cm

3.50"

8.89cm

4.125"

10.48cm

.875"

2.22cm

.078"

0.20cm

Switch

Note:2757D

isupto1.5"

3.81cm

Architects’ and Engineers’ Specifications

The switch shall be comprised of three independent form C triple-

biased reed contacts, wired in SPDT configuration, with Alnico

VIII and Arnox V magnets (2757), or six independent form C

triple-biased reed contacts, wired in DPDT configuration, with

Alnico VIII and Arnox V magnets (2757D). It shall conform to

the specifications for Class IV Preadjusted Balanced Magnetic

Contacts. A supervised loop shall be provided. The switch shall

have an actuating gapdistance (make) of up to 0.4” (1.031cm).

The switch and magnet shall fit into a standard ANSI cutout for

mortise installation 1.25” (3.18cm) x 4.875” (12.38cm). The

switch and magnet housings shall be nominally 1.25” (3.18cm) x

4.875” (12.38cm) x .875” (2.22cm) (W x L x H). The switch and

magnet shall have faceplates of 14 ga. stainless steel with

mounting holes on 4.125” (10.48cm) centers, countersunk for #8

flathead screws. The contacts and magnets shall be epoxied into

their respective housings. Vinyl cable shall be epoxied into the

switch housing. The switch and magnet shall be specified as GE

Interlogix part number 2757 or 2757D.

Installation

The switch is designed to fit into standard ANSI cutout for

mortise installation of metal doors. If door and jamb are provided

with ANSI cutouts and blanks, simply remove the blanks and

install the switch and magnet in their place. If no cutout is

provided, cut holes (for 2757) 1.25” (3.18cm) x 4.875”

(12.38cm) x 1.25” (3.18cm) D, or (for 2757D) 1.25” (3.18cm) x

4.875” (12.38cm) x 1.88” (4.78cm) D in both the door and jamb.

The switch and magnet should be within .0625” (.16cm) both

vertically and horizontally, for proper alignment.

Part Number Loop Type Electrical Configuration Gap Distance (Make)* Lead Type

2757 Open or Closed SPDT Up to 0.4” 3’ Vinyl Jacketed

2757D Open or Closed DPDT Up to 0.4” 3’ Vinyl Jacketed

Ordering Information

12345 SW Leveton Drive

Tualatin, OR 97062

Phone: 503-692-4052

USA & Canada: 800-547-2556

Technical Service: 800-648-7424

FaxBack: 800-483-2495

11263 Rev B 10/02

Note: The products, materials and specifications covered in this

installation instructions are subject to change without notice as

GE Interlogix strives for continuing product improvement.

* Gap distances are nominal

make distance ± 20%.

Form C (2757, 2757D)

Voltage: 30 VAC

Current: .25 A Max.

Power: 3.0 W Max.



LISTED

Connectors and Switches

604S

WARNING !

Each electrical rating is an individual maximum and cannot be exceeded.

www.GE-Interlogix.com

GE Interlogi

Interlogix 2750 Series Installation guide

Interlogix 2750 Series Installation guide

Interlogix 2750 Series Installation guide

Related papers

Other documents