Maytag D11 Questions

Maytag
Brand
Maytag
Model
D11
Type
Questions

This manual is also suitable for

Frequently Asked Questions:
Maytag (PD) washers,
dryers & Stack Units
Last Revision: November 2005
Page 2
How to change the price of a wash cycle (PD)?
This brief manual will answer the most commonly asked questions we receive for the Maytag product
range. If this does not answer your question, please phone our National After Sales Department on
1300 RICHARD (742 427).
Q: My Maytag Washer is a ‘PD’ model with an electronic screen –
How do I change the price of my wash cycles?
a. Unlock the service Hatch on the top of the
machine and remove as shown
b. On the control panel (as shown) press the ‘Woollens’ button: the
display will change to show the ‘6’ series as seen in the picture.
c. The ‘6’ is a program number. The second number shown
represents the number of coins which make up the cycle
price. In Australia, the value of the coin is 20 cent pieces (for
Dual $1 and 20cent mechanisms)
i.e.: 20cent X 16 pieces (as seen)= cycle price of $3.20
d. To increase the price of your cycle, press the ‘permanent press’ button the appropriate number
of times.
i.e.: Your current wash is $3.20, and you want to increase
to $4.00. Press ‘permanent press’ button 4 times to
increase the number on screen to 20 (as shown), making
your price 20cent X 20 pieces = cycle price of $4.00
e. Once price is set, replace and lock the service hatch
f. Most washers are factory set for only 1 standard price for every cycle type (Whites: Hot wash,
Colours: Warm wash, Bright Colours: Cold Wash). If you have requested a ‘3 cycle’ price
structure from the factory, you can adjust each individual cycle price.
At step b. above, by pressing the ‘Woollens’ button multiple times, your on screen display will show
the words, Hot or Warm or Cold, depending on how many times you press ‘woollens’. Then follow
the rest of the steps for each different cycle if required.
*Please Note: if you make a mistake, you cannot cancel this change you just made. Follow the same steps above
and change the settings to be as you prefer. The counter range is between 0 – 49. 49 is the max and will then
revert back to 0 to begin counting again.
The counter will only increase, so if you currently have it set at 20 and
want to change to 18, you must keep pressing the ‘permanent press’ button until the counter has reached the
max and then reverted back past 0 and reaches 18
Email: [email protected] Web: www.richardjay.com.au
Page 3
How to change the price or time for dryer cycles?
This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).
Q: How do I change the price or the length of time for cycles on my Dryer?
Be careful when adjusting this
: if you make a change to the price it will affect the
drying time. These 2 features are directly linked
1. Open the service hatch, and press the ‘Permanent Press’
button to scroll through on screen display. The screen will
show the ‘6’ series which controls the number of coins
required (cycle price) and the ‘7’ series which changes the
length of time for each dry cycle
2. ‘6’ series: the second number in this display is the number
of 20 cent coins required for a cycle.
i.e.: If the screen shows 6 10 - this means 10 X
20cent coins = $2.00 per dry cycle
3. ‘7’ series: the second number in this display controls the length of the cycle COMBINED
together with the number of coins from the ‘6’ series.
i.e.: If the screen shows 7 03 - this means that 10 (from above) X 3 = 30 minute cycle
@ $2.00 /cycle.
If you adjust your price to read 6 12 ($2.40/cycle), it will then adjust the time as well: 12
X 3, cycle now = 36 minutes @ $2.40
If you adjust your price to read 6 15 ($3.00/cycle), you could adjust your time back to 2
to stay at a 30 minute cycle: 15 X 2, cycle now = 30 minutes @ $3.00
Email: [email protected] Web: www.richardjay.com.au
Page 4
How to begin a wash cycle without coins?
This brief manual will answer the most commonly asked questions we receive for the Maytag product
range. If this does not answer your question, please phone our National After Sales Department on
1300 RICHARD (742 427).
Q: I want to do my own washing without paying for it:
How can I start a wash cycle without using any coins?
a. Unlock the service hatch on the top of the
machine and remove as shown
b. On the control panel (as shown) press the ‘Delicates & Knits’ button
for approx 3 seconds and then press ‘Permanent Press’ once: the
display will change to show ‘CC’ as seen in below
c. Now replace the service hatch and the display will change to
display ‘0’ minutes left as seen in this picture
d. Now open the machine lid or front door, select your cycle and fill as normal. This method gives
you a complete cycle for free
Q: I want to run a quick service check to make sure my washer is functioning
properly?
a. Unlock the service hatch on the top of the
machine and remove as shown
b. On the control panel (as shown) press the ‘Delicates & Knits’ button for
approx 3 seconds and then press ‘Woollens’ once: this will run through a
quick diagnostic service check. If any errors are present they will display
on screen, and please refer to your original Instructions manual
Email: [email protected] Web: www.richardjay.com.au
Page 5
When the service hatch is open, what do the
numbers on the display mean?
This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).
Q: What do the numbers on the screen mean when the service hatch is open and
the display is in programming mode?
There are several options available here, but your display will depend on what settings you have
requested from the factory. Available options are a Cycle Count option, and a Money Count option.
If neither of these options have been requested, your machine will display the default factory preset
1. If you have NOT requested either extra option to be preset,
when you open your service hatch, the screen will default
to the ‘6’ series. For further information, see FAQ document
Change Wash Cycle Pricing
2. If you have the Cycle Count option activated, your display
will change between the ‘1’ series and ‘2’ series display.
These two combined, show you how many cycles your
washer has completed. From these two displays, take the
second number from each and combine to show the cycle
count.
I.e.: from ‘1’ take the 15 and from ‘2’ take the 64 and
combine. This washer has completed 1564 Wash cycles.
3. If you have the Money Counter activated, your display will
change between the ‘3’, ‘4’, and ‘5’ series display’s. These
three combined will display how much income has been
generated by this machine. From these three displays, take the
second number from each and combine to show the Money
count.
I.e.: from ‘3’ take the 42 and from ‘4’ take the 48 and
from ‘5’ take the 80 and combine. This washer has
collected $4248.80 in revenue.
Please be aware that once either of these counters have
been activated, they cannot be de-activated
5. To move through any of these display options (when activated),
press the ‘Woollens’ button
Email: [email protected] Web: www.richardjay.com.au
Page 6
What does it mean if the rinse cycle does not
complete properly?
This brief manual will answer the most commonly asked questions we receive for the Maytag product
range. If this does not answer your question, please phone our National After Sales Department on
1300 RICHARD (742 427).
Q: My Maytag Washer will run through the wash part of the cycle but the rinse part
of the cycle does not complete properly?
Water temperature description for all wash cycles:
Whites: Hot wash, cold rinse
Colours: Warm wash, cold rinse
Bright Colours: Cold wash, cold rinse
a. Cold water is used for every rinse cycle, regardless of the wash cycle chosen.
b. Check your cold water tap to make sure you it is turned on and is flowing to the
washer. If the water supply is working properly, it is likely that the water valve has an
internal problem.
**Please phone us for a service appointment immediately on 1300 742 427
Email: [email protected] Web: www.richardjay.com.au
Page 7
How to reset the machine when the display shows
0 minutes and will not reset?
This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).
Q: What does it mean when after the cycle has finished, I have opened the door,
but the display shows 0 minutes and does not reset?
1. This means that the lid switch or door switch (depending on model) is stuck. On washing
machines, it can get stuck if there is a build up of soap. To release the switch, simply clean
away the excess soap, or spray some CRC into that spot to release the button
Top Load Washer Front Load Washer Front Load Dryer
Switch Placement
The lid switch (or door switch) acts as a reset for the digital display. At the end of a cycle, this
button is normally released when the door is opened to remove clothing, and then depressed when
the door is closed. If that sequence does not happen, the digital display will not reset and will stay
showing 0 minutes left
Email: [email protected] Web: www.richardjay.com.au
Page 8
What does it mean if the display panel is flashing?
This brief manual will answer the most commonly asked questions we receive for the Maytag product
range. If this does not answer your question, please phone our National After Sales Department on
1300 RICHARD (742 427).
Q: What does it mean if the display panel is flashing?
1. This means that the money box is not completely secure. There is a switch inside the rear of the
coin housing which must be pressed by the back of the coin box. When the money box was last
emptied, it has not been put back into place properly and has not pushed in the switch. Remove
the box and re-insert, making sure it is securely replaced. Upon doing this, the screen will revert
back to the normal display
Email: [email protected] Web: www.richardjay.com.au
Page 9
How long is the warranty on my machine?
This brief manual will answer the most commonly asked questions we receive for the Maytag product range. If this
does not answer your question, please phone our National After Sales Department on 1300 RICHARD (742 427).
Q: How long is the Warranty on my machine?
Primus Washer and Dryer 12 Months Labour* 36 Months Parts*
Primus Ironer 6 Months Labour* 12 Months Parts*
Maytag Commercial 12 Months Labour* 60 Months Parts*
Ghidini Finishing Equipment 6 Months Labour* 12 Months Parts*
Reconditioned Equipment 1 Months Parts and Labour*
* All warranty is subject to the following conditions:
1. All warranty claims are at the discretion of Richard Jay Laundry Equipment Pty Ltd.
2. The customer is not authorized to arrange repair work. All warranty claims must be directed to Richard Jay Laundry
Equipment Pty Ltd.
3. Where repair work is required for items located outside the metropolitan area the customer is responsible for all travel
and freight costs incurred to repair the items.
4. The company’s liability ceases if the equipment is repaired or interfered with by any person other than those authorized
by Richard Jay Laundry Equipment Pty Ltd. All warranty work is to be carried out by authorized persons only.
5. Warranty will not be covered for faults caused by the incorrect installation of machinery. All machinery must be installed
in accordance with the manufacturers recommendations.
6. Warranty will only be provided for faults caused by normal wear and tear for the specified period of time from date of
purchase.
7. Warranty will not be provided for any faults caused by damage (other than normal wear and tear) including vandalism,
acts of malicious damage, misuse and lack of maintenance.
8. Warranty will not be honoured unless full payment for equipment has been received.
9. All warranty repair work will be carried out during normal working hours. Any work outside of normal hours will result in
the associated costs being born by the customer.
10. Coin jams are not covered by warranty.
11. Pump blockages are not covered by warranty.
12. Failure to carry out preventative maintenance in accordance with manufacturer’s specifications could result in warranty
being void.
13. Consumable items including (but not limited to) the following are not covered by warranty:
Lint screens Ironer Covers Roller ribbons Steam inlet valves
Gasket and washers Drain valve seals Water heating elements Water inlet valves
Rubber Parts (eg. door seals, belts etc)
14. Warranty will not be provided for any faults to machinery caused by chemical damage due to spillage, incorrect
installation or misuse.
15. Reprogramming, change of price or any variations to the microprocessor is excluded from the warranty.
16. Faults caused by power, water or gas interruptions are not covered by warranty.
For all your warranty, service and spare parts please contact the Richard Jay After Sales Department
Phone 1300 RICHARD (742 427) Fax 1300 664 717
Email [email protected]
or [email protected]
Web www.richardjay.com.au
Email: [email protected] Web: www.richardjay.com.au
Page 10
What does the error code mean on my front load
washer?
This brief manual will answer the most commonly asked questions we receive for the Maytag product
range. If this does not answer your question, please phone our National After Sales Department on
1300 RICHARD (742 427).
Q: My Front Load Washer display is showing an error code when I open the service
hatch – what does it mean?
After opening the service Hatch on the top of the machine, the control panel shows an error
code. These are all listed below:
d4 Washer door sensor error on control board (cycles and customer display disabled
until error code is manually cleared)
d5 Blocked coin 1 or coin drop control circuit failure (coin recognition and price display
disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d7 Slow fill detected during previous cycle (cycle paused but can be restarted)
- Check the water taps to make sure they are turned on properly
d8 Last drain was slow
- Check for a blockage in your drain
d9 Low voltage detected for more than 8 seconds
d10 Door lock sensor error (spins inhibited until corrected)
d11 Motor speed error detected (cycle paused but can be restarted)
d13 Blocked coin 2 or coin drop control circuit failure (coin recognition and price display
disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d17 Door not locked (cycle paused but can be restarted
*If you see any of these error codes, unless otherwise mentioned, press and hold ‘Delicates & Knits’
button for approx 3 seconds. This will reset the machine. If the error appears again after the reset,
please call our After Sales Department on 1300 RICHARD (742 427)
Email: [email protected] Web: www.richardjay.com.au
Page 11
What does the error code mean on my single-load
dryer?
This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).
Q: My Single Load Dryer display is showing an error code when I open the service
hatch – what does it mean?
After opening the service Hatch on the top of the machine, the control panel shows an
error code. These are all listed below:
d1 Dryer door sense error on control board or due to power line interference (cycles
and price display disabled until error code is manually cleared)
d4 Dryer motor control circuit error (cycles and customer display disabled
until error code is manually cleared)
d5 Blocked coin 1 or coin drop control circuit failure (coin recognition and price
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d9 Voltage detected below 90vac for 8 seconds
d12 Motor sense error on control board or due to power line interference (cycles and
customer display disabled until error code is manually cleared)
d13 Blocked coin 2 or coin drop control circuit failure (coin recognition and price
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
*If you see any of these error codes, unless otherwise mentioned, press and hold ‘Delicates & Knits’
button for approx 3 seconds. This will reset the machine. If the error appears again after the reset,
please call our After Sales Department on 1300 RICHARD (742 427)
Email: [email protected] Web: www.richardjay.com.au
Page 12
What does the error code mean on my stack
washer & dryer?
This brief manual will answer the most commonly asked questions we receive for the Maytag product
range. If this does not answer your question, please phone our National After Sales Department on
1300 RICHARD (742 427).
Q: My Stack Washer & Dryer display is showing an error code when I turn the
access panel key – what does it mean?
After opening the access panel on the front of the machine, the control panel shows an error
code. These are all listed below:
d1 Dryer door sense error on control board or due to power line interference (dryer
cycles and dryer display disabled until diagnostic code is manually cleared)
d2 Washer door sense error on control board or due to power line interference
(washer cycles and display disabled until diagnostic code is manually cleared)
d4 Dryer motor circuit error (dryer cycles and dryer display disabled until diagnostic
code is manually cleared)
d5 Blocked coin 1 or coin drop control circuit failure (coin recognition and entire
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d7 Slow fill detected during previous cycle (washer cycle paused but can be re-started)
d8 Last drain was slow
d9 Voltage detected below 90vac for 8 seconds
d10 Washer door lock sense error or due to power line interference (washer spins
inhibited until corrected)
d11 Washer motor speed error detected (washer cycle paused but can be re-started)
d12 Dryer motor sense error on control board or due to power line interference (dryer
cycles and display disabled until diagnostic code is manually cleared)
d13 Blocked coin 2 or coin drop control circuit failure (coin recognition and entire display
disabled while blockage persists)
*If you see any of these error codes, unless otherwise mentioned, press and hold ‘Delicates & Knits’
button for approx 3 seconds. This will reset the machine. If the error appears again after the reset,
please call our After Sales Department on 1300 RICHARD (742 427)
Email: [email protected] Web: www.richardjay.com.au
Page 13
What does the error code mean on my stack
dryer?
This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).
Q: My Stack Dryer display is showing an error code when I turn the access panel
key – what does it mean?
After opening the access panel on the front of the machine, the control panel shows an
error code. These are all listed below:
d2 Lower dryer thermistor circuit error on control board (cycles disabled on the lower
machine until error code is manually cleared)
d3 Lower dryer temperature too high (cycles disabled on the lower machine until
error code is manually cleared)
d4 Lower dryer motor control circuit error (lower dryer cycles and lower display
disabled until error code is manually cleared)
d5 Blocked coin 1 or coin drop control circuit failure (coin recognition and price
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d9 Voltage detected below 90vac for 8 seconds
d12 Lower dryer motor sense error on control board or due to power line interference
(lower cycles and lower dryer display disabled until error code is manually cleared)
d13 Blocked coin 2 or coin drop control circuit failure (coin recognition and price
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d14 Upper dryer motor sense error on control board or due to power line interference
(upper cycles and upper dryer display disabled until error code is manually
cleared)
d18 Upper dryer thermistor circuit error on control board (cycles disabled on the upper
machine until error code is manually cleared)
d19 Upper dryer temperature too high (cycles disabled on the upper machine until
error code is manually cleared)
d20 Upper dryer motor control circuit error (upper dryer cycles and upper display
disabled until error code is manually cleared)
*If you see any of these error codes, unless otherwise mentioned, press and hold ‘Delicates & Knits’
button for approx 3 seconds. This will reset the machine. If the error appears again after the reset,
please call our After Sales Department on 1300 RICHARD (742 427)
Email: [email protected] Web: www.richardjay.com.au
Page 14
What does the error code mean on my top-load
washer?
This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).
Q: My Top Load Washer display is showing an error code when I open the service
hatch – what does it mean?
After opening the service Hatch on the top of the machine, the control panel shows an
error code. These are all listed below:
d1 Water level detection error on control board (cycles and customer
display disabled until error code is manually cleared)
d4 Washer lid sense error on control board (cycles and customer display
disabled until error code is manually cleared)
d5 Blocked coin 1 or coin drop control circuit failure (coin recognition and price
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
d7 Last drain was slow
- Check for a blockage in your drain
d8 Last drain occurring during final spin was slow
d9 Voltage detected below 90 vac for 8 seconds
d12 Motor sense error detected on control board
d13 Blocked coin 2 or coin drop control circuit failure (coin recognition and price
display disabled while blockage persists)
- If you know how, you can try to unblock the coin or phone for a service call.
*If you see any of these error codes, unless otherwise mentioned, press and hold ‘Delicates & Knits’
button for approx 3 seconds. This will reset the machine. If the error appears again after the reset,
please call our After Sales Department on 1300 RICHARD (742 427)
Email: [email protected] Web: www.richardjay.com.au
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Maytag D11 Questions

Maytag
Brand
Maytag
Model
D11
Type
Questions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents