Sony HT-S500RF Operating instructions

K:\081\Win7 CS\4735136211_HT-S500RF-S700RF_GB-FR-AR-

PR(cs6)\4735136211_HT-S500RF-S700RF_GB-FR-AR-

PR\00COV\010COV.fm

masterpage:

Right

HT-S500RF/S700RF

4-735-136-21(1)

HT-S500RF/S700RF

Operating Instructions

GB

Manuel d’instructions

FR

4-735-136-21(1)

Home Theatre System

K:\081\Win7 CS\new2\4735136211_HT-S500RF-S700RF_GB-FR-AR-

PR\00COV\010BCO.fm

masterpage:

Right

HT-S500RF/S700RF

4-735-136-21(1)

HT-S500RF/S700RF

PR

AR

http://www.sony.net/

Home Theatre System

2

GB

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

To reduce the risk of fire, do not cover

the ventilation opening of the appliance

with newspapers, tablecloths, curtains,

etc.

Do not expose the appliance to naked

flame sources (for example, lighted

candles).

To reduce the risk of fire or electric

shock, do not expose this appliance to

dripping or splashing, and do not place

objects filled with liquids, such as vases,

on the appliance.

The unit is not disconnected from the

mains as long as it is connected to the

AC outlet, even if the unit itself has been

turned off.

As the main plug is used to disconnect

the unit from the mains, connect the

unit to an easily accessible AC outlet.

Should you notice an abnormality in the

unit, disconnect the main plug from the

AC outlet immediately.

Do not expose batteries or appliances

with battery-installed to excessive heat,

such as sunshine and fire.

Indoor use only.

Recommended cables

Properly shielded and grounded cables

and connectors must be used for

connection to host computers and/or

peripherals.

For the Bar Speaker

The nameplate is located on the bottom

of the Bar Speaker.

WARNING

3

GB

Table of Contents

About These Operating

Instructions ..............................4

What’s in the Box ..........................5

What You Can Do with the

System .....................................6

Guide to Parts and Controls ..........7

Connecting to a TV or Audio

Device

Connecting an Audio Device with an

Analog Audio Cable ...............11

Preparing for Using the

System

Mounting the Bar Speaker and

Surround Speakers on a

Wall .........................................12

Operating the System Using the

Remote Control ..................... 15

When the TV Remote Control does

not Work ................................ 15

Listening to the Sound

Listening to a TV and Other

Devices .................................. 16

Listening to Music on a USB

Device .....................................17

Selecting the Sound Effect

Adjusting the Sound .................... 19

Adjusting the Volume of the

Subwoofer .............................20

Listening to Music/Sound

with the BLUETOOTH®

Function

Listening to Music from a Mobile

Device .................................... 21

Listening to Music on the Mobile

Device with Sony | Music

Center ....................................23

Using the Various Functions

Using the Setup Display ..............24

Using the Control for HDMI

Function .................................27

Notes on HDMI Connections .......28

Saving Power Consumption ........29

Troubleshooting

Troubleshooting ..........................30

Resetting the System ..................35

Additional Information

Specifications ...............................36

Playable Types of Files

(USB Input) .............................38

Supported Input Audio Formats

(HDMI OUT (TV (ARC)) or TV IN

(OPTICAL)) ..............................38

On BLUETOOTH

Communication .....................39

Precautions ..................................40

Connecting a TV

with an HDMI

Cable and/or

Optical Cable



Startup Guide

(separate

document)

GB

4

GB

About These Operating

Instructions

•The instructions in these Operating

Instructions describe the controls on

the remote control.

•Some illustrations are presented as

conceptual drawings, and may be

different from the actual products.

•The default settings are underlined on

each feature description.

•The text enclosed in double quotation

mark (“--”) appears in the front panel

display.

5

GB

What’s in the Box

•Bar Speaker (1)

•Subwoofer (1)

• Surround speaker (HT-S500RF only) (2)

• Surround speaker (2), speaker base (2),

and screw (8) (HT-S700RF only)

• Remote control (1)

• R03 (size AAA) battery (2)

•HDMI cable (1)

• WALL MOUNT TEMPLATE (1)

•Startup Guide

• Operating Instructions

6

GB

What You Can Do with the System

“Listening to a TV and Other Devices”

(page 16)

Blu-ray Disc™ player, cable

box, satellite box, etc.

Connecting the TV

(refer to “Startup Guide” (separate document) or

“Connecting an Audio Device with an Analog

Audio Cable” (page 11))

“Using the Control for HDMI Function”

(page 27)

“Listening to Music

on a USB Device”

(page 17)

“Listening to Music

from a Mobile Device”

(page 21)

“Listening to Music on

the Mobile Device

with Sony | Music

Center” (page 23)

HT-S500RF

HT-S700RF

7

GB

Guide to Parts and Controls

Details are omitted from the illustrations.

Front

 (power) button

Turns on the system or sets it to

standby mode.

 (input select) button

(page 16)

 BLUETOOTH button (page 21)

 +/– (volume) buttons

 Remote control sensor (page 15)

Point the remote control at the

remote control sensor to operate

the system.

 Front panel display

 (USB) port (page 17)

 BLUETOOTH indicator

– Lights in blue: BLUETOOTH

connection is established (the

BLUETOOTH input is selected).

– Flashes quickly in blue: While

waiting for connection with a

device.

– Flashes in blue: While

reconnecting or performing

pairing.

Subwoofer

8

GB

Rear

 SPEAKERS jacks

 IR REPEATER jack

 TV IN (OPTICAL) jack

 HDMI OUT (ARC) jack

Connect a TV that has an HDMI

input jack with an HDMI cable.

The system is compatible with

Audio Return Channel (ARC). ARC

is the function that sends TV

sound to an AV device such as the

system from the TV’s HDMI jack.

 ANALOG IN jack (page 11)

 AC power cord (mains lead)

9

GB

 INPUT (page 16)

Selects the input source.

 AUTO SOUND (page 19)

Selects AUTO SOUND for the sound

effect.

 CINEMA (page 19)

Selects CINEMA for the sound

effect.

 VOICE (page 19)

Turns on/off the voice mode.

  (volume) +*/–

Adjusts the volume.

 SW  (subwoofer volume) +/–

Adjusts the subwoofer volume.

 MENU (page 24)

Turns on/off the menu in the front

panel display.

/ (page 17, 24)

Selects the menu items.

Selects the content on the TV screen

for USB playback.

ENTER (page 17, 24)

Enters the selection.

Plays the content that is selected by

/ for USB playback.

BACK (page 17, 24)

Returns to the previous display.

Stops USB playback.

/ (previous/next)

(page 17, 21)

Press to select the previous/next

track or file.

Hold down to search backward or

forward.

 (power)

Turns on the system or sets it to

standby mode.

 STANDARD (page 19)

Selects STANDARD for the sound

effect.

 MUSIC (page 19)

Selects MUSIC for the sound effect.

 NIGHT (page 19)

Turns on/off the night mode.

Remote Control

10

GB

  (muting)

Mutes the sound temporarily.

Pressing the button while muting

cancels muting.

 DIMMER

Adjusts the brightness of the front

panel display.

“BRGHT”  “DARK”  “OFF”

• The front panel display is turned

off when “OFF” is selected. It turns

on automatically when you

operate the system, then turns off

again if you do not operate the

system for several seconds.

However, in some cases, the front

panel display may not turn off. In

this case, the brightness of the

front panel display is same as

“DARK.”

  (play/pause)* (page 17, 21)

Plays, pauses, or resumes playback.

*The  + and  buttons have a tactile

dot. Use it as a guide during operation.

About the replacement of

batteries for the remote control

When the system does not respond by

operating with the remote control,

replace two batteries with new

batteries.

Use R03 (size AAA) manganese

batteries for replacement.

11

GB

Connecting a TV with an

HDMI Cable and/or

Optical Cable

Refer to Startup Guide (separate

document).

Connecting an Audio

Device with an Analog

Audio Cable

To connect portable audio devices such

as smartphones and WALKMAN® to the

system, connect them via the ANALOG

IN jack on the system.

For listening to the connected device,

see “Listening to a TV and Other

Devices” (page 16).

Connecting to a TV or Audio

Device

Smartphone,

WALKMAN®, other

audio devices, etc.

Analog

audio out

Analog audio cable

(not supplied)

12

GB

Mounting the Bar

Speaker and Surround

Speakers on a Wall

You can mount the Bar Speaker and

surround speakers on a wall.

HT-S500RF

HT-S700RF

• Prepare screws (not supplied) that are

suitable for the wall material and

strength. As a plasterboard wall is

especially fragile, attach the screws

securely in the wall beam. Install the

speakers horizontally, hung by screws in

studs in a continuous flat section of the

wall.

• Have the installation done by a Sony

dealer or licensed contractor and pay

special attention to safety during the

installation.

• Sony shall not be held responsible for

accidents or damage caused by improper

installation, insufficient wall strength,

improper screw installation or natural

disaster, etc.

1 Prepare two screws (not supplied)

that are suitable for the wall

mount holes on the rear of the Bar

Speaker.

2 Stick WALL MOUNT TEMPLATE

(supplied) on a wall.

1 Align TV CENTER LINE () of

WALL MOUNT TEMPLATE with the

center line of your TV.

2 Align TV BOTTOM LINE () of

WALL MOUNT TEMPLATE with the

bottom of your TV, then stick

Preparing for Using the System

Notes

Mounting the Bar Speaker

on a Wall

Hole on the rear of the Bar Speaker

4mm

More than 30 mm

5 mm

10 mm

Center of the TV

WALL MOUNT

TEMPLATE

Adhesive tape,

etc.

13

GB

WALL MOUNT TEMPLATE on a

wall by using a commercially

available adhesive tape, etc.

3 Fasten the screws into the marks

on SCREW LINE () of WALL

MOUNT TEMPLATE as the

illustration below.

4 Remove WALL MOUNT TEMPLATE.

5 Hang the Bar Speaker on the

screws.

Align the holes of the rear of the Bar

Speaker with the screws, then hang

the Bar Speaker on the two screws.

When sticking WALL MOUNT TEMPLATE,

smooth it out fully.

For HT-S500RF

1 Prepare a screw (not supplied) for

each speaker that is suitable for

the wall mount hole on the rear of

the surround speaker.

2 Fasten the screw in the wall.

The screw should protrude as

illustration.

Screws

Marks

6 mm to

7mm

297.5 mm

Note

Mounting the Surround

Speakers on a Wall

Hole on the rear of the surround speaker

4mm

More than 30 mm

5 mm

10 mm

8 mm to

9mm

14

GB

3 Hang the surround speaker on the

screw.

Align the hole of the rear of the

surround speaker with the screw,

then hang the surround speaker on

the screw.

For HT-S700RF

1 Prepare two screws (not supplied)

for each speaker that are suitable

for the wall mount holes on the

rear of the surround speaker.

2 Fasten the screws in the wall.

The screw should protrude as

illustration.

3 Hang the surround speaker on the

screws.

Align the holes of the rear of the

surround speaker with the screws,

then hang the surround speaker on

the screws.

Hole on the rear of the surround speaker

4mm

More than 30 mm

5 mm

10 mm

1,000 mm

8 mm to

9mm

15

GB

Operating the System

Using the Remote Control

Point the remote control at the

subwoofer’s remote control sensor.

When the TV Remote

Control does not Work

When the Bar Speaker obstructs the

remote control sensor of the TV, the TV

remote control may not work. In that

case, enable the IR repeater function of

the system.

You can control the TV with the TV

remote control by sending the remote

signal from the rear of the Bar Speaker.

1 Connect the IR repeater cord to

the subwoofer.

Refer to Startup Guide (separate

document).

2 Press MENU.

The menu item appears in the front

panel display.

3 Select “SYS >” – “IRRPT” by using

//ENTER.

4 Select “ON” by using //ENTER.

To turn off the IR repeater function,

select “OFF.”

5 Press MENU to turn off the menu.

•Be sure to check that the TV remote

control cannot control the TV, and then

set the IR repeater function to on. If it is

set to on when the remote control can

control the TV, appropriate operation

may not be obtained because of the

interference between the direct

command from the remote control and

the command via the Bar Speaker.

•On some TVs, this function may not work

correctly. In this case, place the Bar

Speaker slightly further away from the TV.

Notes

16

GB

Listening to a TV and

Other Devices

1 Press INPUT repeatedly.

When you press INPUT once, the

input source is changed and the

selected input source appears in the

front panel display.

Each time you press INPUT, the

input source changes cyclically as

follows.

“TV”  “ANALG”  “BT”  “USB”

2 Adjust the volume.

• Adjust the volume by pressing 

+/– on the remote control.

• Adjust the subwoofer volume by

pressing SW  +/– on the remote

control (page 20).

Tip

You can also select the input by pressing

on the subwoofer.

Listening to the Sound

“TV”

• TV compatible with the Audio Return

Channel (ARC) function that is

connected to the HDMI OUT (ARC) jack

• TV that is connected to the TV IN

(OPTICAL) jack

When you connect the TV to both the

HDMI OUT (ARC) and TV IN (OPTICAL)

jacks, the input of the HDMI OUT (ARC)

jack has priority.

INPUT

 +/–

SW  +/–

“ANALG”

Audio device (smartphone, WALKMAN®,

etc.) that is connected to the ANALOG IN

jack

“BT”

BLUETOOTH device that supports A2DP

For details, see “Listening to Music/

Sound with the BLUETOOTH® Function”

(page 21).

“USB”

USB device that is connected to the

(USB) port

For details, see “Listening to Music on a

USB Device” (page 17).

17

GB

Listening to Music on a

USB Device

You can play music files stored on a

connected USB device.

For playable types of files, see “Playable

Types of Files (USB Input)” (page 38).

• To view the USB content list on the TV

screen, make sure you connect the

system to the TV using an HDMI cable.

• Change the input of the TV to the input to

which the system is connected.

1 Connect the USB device to the

(USB) port.

2 Press INPUT repeatedly to select

“USB” in the front panel display.

“READ” appears in the front panel

display and the system starts

reading data of the USB device.

When the reading of data is

completed, the USB content list

appears on the TV screen.

3 Press / to select the content

you want, then press ENTER.

The selected content starts playing.

4 Adjust the volume.

• Adjust the volume by pressing 

+/– on the remote control.

• Adjust the subwoofer volume by

pressing SW  +/– on the remote

control (page 20).

To select the play mode

You can select the play mode for USB

playback, such as repeat play or random

play, from the menu.

1 Press MENU.

The menu item appears in the front

panel display.

2 Select “USB >” – “REPT” by using //

ENTER.

Notes

ENTER

 +/–



/

INPUT

/

SW  +/–

MENU

18

GB

3 Select the play mode by using //

ENTER.

•“NONE”

: Plays back all tracks under

the current folder.

•“ONE”: Repeats one track.

•“FLDER”: Repeats all tracks in a

folder.

•“SHFFL”: Repeats all tracks in a

folder in random order.

4 Press MENU to turn off the menu.

Other operations

• Do not remove the USB device during

operation. To avoid data corruption or

damage to the USB device, turn the

system off before connecting or

removing the USB device.

• “NOUSB” flashes in the front panel display

if you connect an unsupported or broken

USB device.

• Depending on the file format, rewind and

fast forward do not work.

 Playing time

 Total playing time

 Selected file index/Total files in the

folder

 Play mode

 Playback status

 Rewind/fast forward speed

The following messages appear on the

TV screen depending on the status of

the USB device.

•[No USB]

No USB device is inserted.

• [Waiting]

The system is searching a USB device.

• Depending on the playback source, some

information may not be displayed.

• Depending on the play mode, the

information displayed may be different.

To Do this

Pause or resume

playback

Press .

Select the previous or

next track

Press /.

Search backward or

forward (rewind/fast

forward)

Press and hold

/.

Notes

Information of USB Device

on the TV Screen

Notes

19

GB

Adjusting the Sound

You can easily enjoy pre-programmed

sound effects that are tailored to

different kinds of sound sources.

Press AUTO SOUND, CINEMA, MUSIC,

or STANDARD to select the sound

mode.

The selected sound mode appears in the front

panel display.

You can compress sound in accordance

with the information contained in the

content by setting the night mode to on.

Sound is output at low volume with

minimum loss of fidelity and clarity of

dialog.

Press NIGHT to set the function to on

or off.

When you turn the system off, the night

mode is set to off automatically.

You can make dialogs clearer by setting

the voice mode to on.

Press VOICE to set the function to on

or off.

Selecting the Sound Effect

Enjoying the Sound Effect

that is Tailored to Sound

Sources (Sound Mode)

“AUTO SOUND”

You can enjoy the sound with Sony-

recommended sound mode. The sound

mode is automatically optimized according

to playback content and function.

“CINEMA”

Sounds are played back with surround

effects, and they are realistic and powerful,

making them suitable for movies.

“MUSIC”

Sound effects are optimized for listening to

music.

STANDARD

AUTO SOUND

MUSIC

CINEMA

“STANDARD”

Sound effects are optimized for the

individual source.

Enjoying Clear Sound with

Low Volume at Midnight

(NIGHT)

Night mode on

“N.ON” appears in the front panel display.

Night mode off

“N.OFF” appears in the front panel display.

Note

Making Dialogs Clearer

(VOICE)

Voice mode on

“V.ON” appears in the front panel display.

Voice mode off

“V.OFF” appears in the front panel display.

20

GB

Adjusting the Volume of

the Subwoofer

The subwoofer is designed for playback

of bass or low frequency sound.

Press SW (subwoofer volume)  +/–

to adjust the volume of the

subwoofer.

When the input source does not contain

much bass sound, such as in TV programs,

the bass sound from the subwoofer may

be difficult to hear.

Note

SW  +/–

Page is loading ...

Sony HT-S500RF Operating instructions

This manual is also suitable for

Sony HT-S500RF Operating instructions

in other languages

Related papers

Other documents