H3C MSR2600-6-X1-GL Installation guide

H3C MSR2600-6-X1-GL Gigabit Router

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W100-20180818

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care, , IRF, NetPilot, Netflow, SecEngine,

SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies

Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. All contents in this document, including

statements, information, and recommendations, are believed to be accurate, but they are presented without

warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions

contained herein.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

The H3C MSR2600-6-X1-GL Gigabit Router Installation Guide includes seven chapters, which

describe the preparing for installation, installing the router, replacement procedure, troubleshooting,

chassis views and technical specifications, LEDs, and slot arrangement.

This preface includes the following topics about the documentation:

• Audience.

• Conventions.

• Documentation feedback.

Audience

This documentation is intended for:

• Network planners.

• Field technical support and servicing engineers.

• Network administrators working with the MSR2600-6-X1-GL Gigabit Router.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

Italic

Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the

New User

window opens; click

OK

.

Convention Description

>

Multi-level menus are separated by angle brackets. For example,

File

>

Create

>

Folder

.

Symbols

Convention Description

WARNING!

An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION:

An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT:

An alert that calls attention to essential information.

NOTE:

An alert that contains additional or supplementary information.

TIP:

An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Represents a wireless terminator unit.

Represents a wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.

T



Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

i

Contents

Preparing for installation ···································································· 1

Safety recommendations ············································································································· 1

Safety symbols ··················································································································· 1

General safety recommendations ··························································································· 1

Electricity safety ·················································································································· 1

Examining the installation site ······································································································· 1

Temperature and humidity ····································································································· 1

Cleanliness ························································································································ 2

Cooling system ··················································································································· 2

ESD prevention ··················································································································· 3

EMI prevention ··················································································································· 3

Lightning protection ············································································································· 4

Rack requirements ·············································································································· 4

Installation tools and accessories ·································································································· 5

Pre-installation checklist ·············································································································· 5

Installing the router ··········································································· 7

Installation prerequisites ·············································································································· 7

Installation flowchart ··················································································································· 7

Installing the router ····················································································································· 8

Mounting the router on a workbench ························································································ 8

Mounting the router in a rack ······························································································· 10

Grounding the router ·········································································································· 12

Installing a SIC ················································································································· 13

Connecting interface cables ································································································· 14

Connecting the console cable and setting terminal parameters ··················································· 15

Connecting the AC power cord ····························································································· 16

Verifying the installation ······································································································ 17

Starting the router ···················································································································· 17

Replacement procedure ·································································· 19

Replacing a SIC ······················································································································ 19

Replacing a transceiver module ·································································································· 19

Troubleshooting ············································································· 20

Power supply failure ················································································································· 20

Symptom ························································································································· 20

Solution ··························································································································· 20

Fan tray failure ························································································································ 20

Symptom ························································································································· 20

Solution ··························································································································· 20

No display on the configuration terminal ························································································ 21

Symptom ························································································································· 21

Solution ··························································································································· 21

Garbled display on the configuration terminal ················································································· 21

Symptom ························································································································· 21

Solution ··························································································································· 21

No response from the serial console port ······················································································ 21

Symptom ························································································································· 21

Solution ··························································································································· 21

Interface module failure ············································································································· 22

Symptom ························································································································· 22

Solution ··························································································································· 22

Restoring the factory settings ····································································································· 22

Scenario 1 ······················································································································· 22

Scenario 2 ······················································································································· 22

Scenario 3 ······················································································································· 23

ii

Reset button usage guidelines ····························································································· 23

Appendix A Chassis views and technical specifications ·························· 24

Chassis views ························································································································· 24

Technical specifications ············································································································· 24

Appendix B LEDs ··········································································· 26

Appendix C Slot arrangement ··························································· 27

Index ··························································································· 28

1

Preparing for installation

Table 1 This document applies to the following device models:

Model Product code

MSR2600-6-X1-GL RT-MSR2600-6-X1-GL

Safety recommendations

Safety symbols

When reading this document, note the following symbols:

WARNING means an alert that calls attention to important information that if not understood or

followed can result in personal injury.

CAUTION means an alert that calls attention to important information that if not understood or

followed can result in data loss, data corruption, or damage to hardware or software.

General safety recommendations

• Keep the router and installation tools away from walk areas.

• Place the router in a dry and flat location and make sure anti-slip measures are in place.

• Remove all external interface cables and power cords before moving the router.

Electricity safety

• Locate the power-off switch in the equipment room before installation. Shut off the power

immediately if an accident occurs. Disconnect the power cord from the router if necessary.

• Make sure the router is reliably grounded.

• Connect the interface cables correctly.

• Use an uninterrupted power supply (UPS).

• Always make sure the power has been disconnected during the installation or replacement

procedure.

Examining the installation site

The router can only be used indoors. To ensure correct operation and a long lifespan for your

router, install it in an environment that meets the requirements described in the following

subsections.

Temperature and humidity

Maintain the temperature and humidity in the equipment room as described in Table 2.

• Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

2

• Lasting low relative humidity can cause washer contraction and ESD and cause problems

including loose mounting screws and circuit failure.

• High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the router.

Table 2 Temperature and humidity requirements

Temperature Humidity

Operating temperature: 0°C to 45°C (32°F to 113°F)

Storage temperature: –40°C to +70°C (–40°F to +158°F)

5% RH to 95% RH, noncondensing

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points, especially when indoor relative humidity is low. In the worst

case, electrostatic adsorption can cause communication failure.

Table 3 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m

3

)

Dust particles

≤ 3 x 10

4

(No visible dust on the tabletop in three days)

NOTE:

Dust diameter ≥ 5 µm

The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and

premature aging of components, as shown in Table 4.

Table 4

Harmful gas limits in an equipment room

Gas Maximum concentration (mg/m

3

)

SO

2

0.2

H

2

S 0.006

NH

3

0.05

NO

2

0.04

Cl

2

0.01

Cooling system

The router uses left-to-right airflow for heat dissipation, as shown in Figure 1.

3

Figure 1 Airflow through the chassis

To ensure good ventilation, follow these guidelines:

• Maintain a minimum clearance of 10 cm (3.94 in) around the air inlet and outlet vents.

• Make sure the installation site has a good ventilation system.

ESD prevention

Preventing electrostatic discharge

To prevent electrostatic discharge (ESD), follow these guidelines:

• Make sure the router and the floor are reliably grounded.

• Take dust-proof measures for the equipment room.

• Maintain the humidity and temperature levels in the acceptable range.

• Always wear an ESD wrist strap and an ESD garment when touching a circuit board or

transceiver module.

• Place the removed interface module on an antistatic workbench with the circuit board upward,

or put it in an antistatic bag.

• Touch only the edges instead of electronic components on the circuit board when you observe

or move a removed interface module.

Attaching an ESD wrist strap

CAUTION:

Use a multimeter to check the resistance of the ESD wrist strap for safety. The resistance reading

should be in the range of 1 to 10 megohm (Mohm) between a human body and the ground.

No ESD wrist strap is provided with the router. Prepare one yourself.

To attach an ESD wrist strap:

1. Wear the wrist strap on your wrist.

2. Lock the wrist strap tight around your wrist to maintain good contact with the skin.

3. Secure the wrist strap lock and the alligator clip lock together.

4. Attach the alligator clip to the grounding screw on the router.

EMI prevention

All electromagnetic interference (EMI) sources, from outside or inside of the router and application

system, adversely affect the router in the following ways:

• A conduction pattern of capacitance coupling.

• Inductance coupling.

4

• Electromagnetic wave radiation.

• Common impedance (including the grounding system) coupling.

To prevent EMI, use the following guidelines:

• If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

• Keep the router far away from radio transmitting stations, radar stations, and high-frequency

devices.

• Use electromagnetic shielding, for example, shielded interface cables, when necessary.

• To prevent signal ports from getting damaged by overvoltage or overcurrent caused by

lightning strikes, route interface cables only indoors.

Lightning protection

To enhance lightning protection for the router, follow these guidelines:

• Make sure the router is reliably grounded.

• Make sure the AC power outlet is reliably grounded.

• Install a lightning protector at the power input end.

• Install a lightning protector at the input end of signal cables routed from outdoors, for example,

E1/T1 cable.

Rack requirements

To install the router in a rack, make sure the rack meets the following requirements:

• The rack has a good ventilation system.

• The rack is sturdy and can support the router and its accessories.

• The rack has a size that can accommodate the router.

• Enough clearances are reserved at the two sides of the router for heat dissipation.

• A minimum of 0.8 m (2.62 ft) of clearance is reserved between the rack and walls or other

devices for heat dissipation and maintenance.

• The headroom in the equipment room is not less than 3 m (9.84 ft).

5

Installation tools and accessories

Figure 2 Installation tools

Figure 3 Installation accessories

Pre-installation checklist

Item Requirements

Installation

site

Ventilation

• A minimum clearance of 100 mm (3.94 in) is reserved around the air

inlet and outlet vents.

• The installation site has a good ventilation system.

Temperature

Operating temperature: 0°C to 45°C (32°F to 113°F)

Storage temperature: –40°C to +70°C (–40°F to +158°F)

Humidity 5% RH to 95% RH (noncondensing)

Cleanliness

Dust concentration ≤ 3 × 10

4

particles/m

3

(no visible dust on the tabletop

over three days)

6

Item Requirements

ESD

prevention

• The router and floor are reliably grounded.

• Dust-proof measures are taken in the equipment room.

• Humidity and temperature are maintained at acceptable levels.

• An ESD wrist strap and ESD garment are available.

• An anti-static workbench and anti-static bags are available.

EMI

prevention

• A single-phase three-wire power receptacle with protection earth (PE)

is available for filtering interference from the power grid.

• The router is far away from radio transmitting stations, radar stations,

and high-frequency devices.

• Electromagnetic shielding, for example, shielded interface cables, is

used as required.

Lightning

protection

• The router is reliably grounded.

• The AC power receptacle is reliably grounded.

• (Optional.) Port lightning protectors are available.

• (Optional.) Power lightning protectors are available.

• (Optional.) Signal cable lightning protectors are available.

Electricity

safety

• A UPS is available.

• The power-off switch in the equipment room is identified and

accessible so that the power can be immediately shut off when an

accident occurs.

Workbench

• The workbench is stable.

• The workbench is reliably grounded.

Rack

• The rack has a good ventilation system.

• The rack is sturdy and can support the router and its accessories.

• The rack has a size that can accommodate the router.

• A minimum of 0.8 m (2.62 ft) of clearance is reserved between the

rack and walls or other devices.

Safety

precautions

The router is far away from any sources of heat or moisture.

Installation

tools and

accessories

• Installation accessories supplied with the router are ready.

• User-supplied tools are ready.

Reference

• Documents shipped with the router are available.

• Online documents are available.

7

Installing the router

WARNING!

To avoid injury, do not touch bare wires, terminals, or parts with high-voltage hazard signs.

IMPORTANT:

• The barcode on the router chassis contains product information that must be provided to local

sales agent when you return a faulty router for repair.

• Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to

open the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any

consequence.

Installation prerequisites

• You have read "Preparing for installation" carefully.

• All requirements in "Preparing for installation" are me

t.

Installation flowchart

You can install the router on a workbench or in a rack.

Determine the installation method according to the installation environment. Follow the installation

flowchart shown in Figure 4 to install the route

r.

8

Figure 4 Installation flowchart

Installing the router

Mounting the router on a workbench

IMPORTANT:

• Make sure the workbench is clean, stable, and reliably grounded.

• Maintain a minimum clearance of 100 mm (3.94 in) around the router for heat dissipation.

• Do not place heavy objects on the router.

Yes

No

Start

Ground the router

Install a SIC

Connect interface

cables

Connect the router to a

configuration terminal

Connect the power cord

Verify the installation

Power on the router Troubleshoot the router

Power off the routerOperating correctly?

End

Mount the router on a

workbench

Mount the router in a rack

Determine the

installation position

Workbench-mounting

Rack-mounting

9

To mount the router on a workbench:

1. Place the router upside down on the workbench and attach the rubber feet to the four round

holes in the chassis bottom.

2. Place the router upside up on the workbench. Make sure the rubber feet stand securely on

the workbench.

Figure 5 Mounting the router on a workbench

10

Mounting the router in a rack

Router dimensions and rack requirements

Figure 6 Router dimensions

Table 5 Router dimensions and rack requirements

Chassis dimensions Rack requirements

• Height—44.2 mm (1.74 in)/1 RU

• Width—360 mm (14.17 in)

• Depth—420 mm (16.54 in)

{ 300 mm (11.81 in) for the chassis

{ 60 mm (2.36 in) for connecting the AC

power cord at the front

{ 60 mm (2.36 in) for connecting the E1

cable at the rear

• A minimum of 0.6 m (1.97 ft) in depth

(recommended)

• A minimum of 80 mm (3.15 in) between the

front rack posts and the front door

• A minimum of 360 mm (14.17 in) between the

front rack posts and the rear door

Installing the router in a rack

CAUTION:

The mounting brackets can support only the weight of the router. Do not place objects on the

router.

To install the router in a rack:

60 mm

(2.36 in)

300 mm

(11.81 in)

60 mm

(2.36 in)

Mounting

bracket

Power cord

E1 cable

11

1. Use a mounting bracket to mark the cage nut installation holes in the front rack posts, as

shown in Figure 7.

Make

sure the cage nut installation holes on the front rack posts are on a horizontal line.

Figure 7 Marking cage nut installation holes

2. Install cage nuts, as shown in Figure 8.

a. Insert one ear of a cage nut into the marked installation hole.

b. Use a flathead screwdriver to push another ear into the same hole.

Figure 8 Installing cage nuts

3. Attach mounting brackets to both sides of the router, as shown in Figure 9.

12

Figure 9 Attaching mounting brackets to the router

4. Use M6 screws to attach the mounting brackets on the router to the front rack posts, as

shown in Figure 10.

Figure 10

Securing the router to the rack

Grounding the router

CAUTION:

• Correctly connecting the grounding cable is crucial to lightning protection and EMI protection.

When you install and use the router, first ground the router reliably.

• Ensure a minimum resistance of 5 ohms between the router and the ground.

A grounding cable is provided with the router. You can use the grounding cable to ground the router.

To ground the router:

1. Remove the grounding screw from the grounding hole in the rear panel of the chassis.

2. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding

hole.

3. Use a Phillips screwdriver to fasten the grounding screw into the grounding screw hole.

13

4. Attach the other end of the grounding cable to the grounding strip.

Figure 11 Connecting the grounding cable to the router

Installing a SIC

CAUTION:

SIC interface modules are not hot swappable. Make sure the router is powered off before installing

a SIC.

To install a SIC:

1. Use a Phillips screwdriver to remove the fastening screws on the filler panel and remove the

filler panel.

2. Push the SIC slowly into the slot along the guide rails until it makes close contact with the

backplane of the router.

3. Fasten the captive screws on the SIC.

Figure 12 Installing a SIC

Page is loading ...

H3C MSR2600-6-X1-GL Installation guide

H3C MSR2600-6-X1-GL Installation guide

Related papers

Other documents