MELICONI Facile User manual

Brand: MELICONI

Model: Facile

Type: User manual

Thank you for choosing Meliconi.

The spare FACILE remote control can be used for all the main functions

for TVs of the makes listed at the back of the pack.

Keep your Instructions Booklet and Code Booklet for future reference.

USING THE BUTTONS AND FUNCTIONS

Light indicator.

Confirm button.

To select the next (P+)

or previous (P-)

channel or program.

These buttons can

also be used to move

up and down

in the MENU.

Mute button.

Additional colour button

or function.

TV ON/OFF button.

Fastext functions

or access to the

brightness and colour

controls, directly or

using the SHIFT button.

Teletext buttons:

to access Teletext

to close Teletext and

return to normal

viewing Teletext page

hold function.

Number keys.

To access your MENU.

To move within the MENU,

use the +/- and P +/-

or SHIFT buttons together

with +/- P +/- depending

on the model of your

original remote control.

Control the volume using +/ -.

These buttons can also be

used to move to the right

and left in the MENU.

To select an external terminal.

Used to access additional

commands and to program

the remote control.

The functions described above are only operative

if your appliance also has them.

GB Use

SHIFT

SET-UP

Read these instructions

carefully before programming

your remote control!

MAKE SEARCH PROGRAMMING MODE

1.Make sure that the TV is ON.

2.In the code book enclosed, look for

the make of your TV and make a note

of the code indicated at the side

(e.g. Philips 001) or the code for the

make indicated by the arrow.

3.Hold down the SHIFT and ON/OFF

buttons together until the light

indicator at the top starts to flash

indicating that the remote control is

programming.

4.Release the buttons,

within 15 seconds, enter the make

code previously identified (e.g. 001).

The light indicator flashes

more quickly to indicate

that the remote control

is ready for the search.

5.Point the remote control at the TV.

Press and release one of

the most frequently-used

keys several times STOPPING

when the appliance responds

correctly to the command.

6.When the TV responds correctly,

press SHIFT to confirm.

Three flashes indicate that the

operation has been completed

correctly.

Additional check

Check that some of the other functions

used on your original remote control are

working correctly. If the commands

function incorrectly or erratically, you

have probably entered a code for a

similar but different remote control.

In this case, repeat the search

procedure from point 3.

Identify and take note of the TV

code which you have searched for

following the code noting procedure

(see “NOTING THE PROGRAMMED

CODE” section).

SHIFT

NOTE : THE LIGHT INDICATOR

STOPS FLASHING

The remote control leaves the

programming mode and the light

indicator stops flashing:

•if no buttons are pressed for 15

seconds

•if an invalid make code is entered

•if the code search list is completed.

In this case, go back to point 3 or

switch to programming mode C.

FITTING THE BATTERIES

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new AAA/LR03 alkaline batteries.

Insert the batteries as shown.

•The batteries must be changed once a year.

•Change the batteries if the light indicator starts to

flash during use, this indicates that the batteries are

low and should be changed.

•When you remove the batteries, fit the new ones

within 5 minutes or you may have to reprogram your

remote control.

•Make a note of the codes for your TV on the

adhesive label inside the battery cover. This note will

be handy if you have to reprogram your control.

To program the Facile remote

control, follow the indications

in section A , Bor C.

Additional check

Check that some of the other

functions used on your original remote

control are working correctly.

If the commands function incorrectly

or erratically, you have probably

entered a code for a similar but

different remote control.

In this case, repeat the search

procedure from point 2.

1.Make sure that the TV is ON.

2.Hold down the SHIFT

and ON/OFF buttons together

until the light indicator at the

top starts to flash indicating

that the remote control is

programming.

3.Release the buttons.

Within 15 seconds,

enter the code 000.

The light indicator flashes more

quickly to indicate that the remote

control is ready for the search.

4.Point the remote control at the TV.

Press and release one of the

most frequently used keys

several times STOPPING when

the appliance responds correctly

to the command.

5.When the TV responds correctly,

press SHIFT to confirm.

Three flashes indicate that

the operation has been

completed correctly.

Identify and make a note of the

code which you have searched

for following the code noting procedure

(see “NOTING THE PROGRAMMED

CODE” section).

NOTE : THE LIGHT INDICATOR

STOPS FLASHING

The remote control leaves the

programming mode and the light

indicator stops flashing:

•if no buttons are pressed

for 15 seconds

•if the code search list is completed.

1.Make sure that the TV is ON.

2.In the code book enclosed,

look for the make of your TV

and make a note of the first

code indicated BENEATH

the make previously identified

(e.g. Philips 103).

3.Hold down the SHIFT

and ON/OFF buttons together

until the light indicator at the top

starts to flash indicating that the

remote control is programming.

4.Release the buttons.

Within 15 seconds, enter the

code previously identified

(e.g. 103). Three flashes indicate

that the code has been saved

correctly. If not, try the code entry

procedure again from point 3.

Additional check

Point the remote control at the TV.

Check that the appliance responds

correctly to the commands sent.

If there is no response or the appliance

only responds partially or incorrectly,

it is probable that you have used

the wrong code. In this case, try the

procedure again from point 3.

This time, however, use the

NEXT CODE in the list (e.g. 111).

Make a note of the TV code

used to program the remote control

on the adhesive label supplied;

stick the label inside the battery cover,

for rapid consultation.

NOTE : THE LIGHT INDICATOR

STOPS FLASHING

The remote control leaves the

programming mode and the light indicator

stops flashing:

•if no buttons are pressed

for 15 seconds.

•if an invalid make code is entered.

DIRECT CODE ENTRY

GLOBAL SEARCH REMOTE CONTROL PROGRAMMING

This operation may take up to 30 minutes.

SHIFT

Count the number of flashes for

each code number.

For example, for the code 306, the

button flashes three, zero and six

times to give:

= 3

= 0

= 6

4.Note this code on the label

inside the battery cover,

for rapid consultation.

NOTING THE PROGRAMMED CODE

To find the code for your remote control:

1.Hold down the SHIFT and ON/OFF

buttons together until the light

indicator at the top starts to flash.

2.Release the SHIFT and ON/OFF

buttons and then press and release

the 1-/-- button.

3.After a few seconds, the light

indicator communicates the

code you are looking for by flashing

the three numbers separately.

USING THE ADDITIONAL COMMANDS WHICH DO NOT

APPEAR ON THE KEYPAD

Although not indicated on the keypad, some buttons can be used for

additional commands.

1.Use your Facile remote control to find them by pressing the following buttons one by one:

2.The most frequently used additional commands like MENU SCROLL –COLOUR-

BRIGHTNESS and NORMALISATION are located as follows:

normalisation

1-/--

SHIFT

Always write down the 3-digit code for your remote control on the label

inside the battery cover after running the search and saving the code.

This may be useful if you need to reprogram your remote control in the

event of accidental cancellation or when you change used batteries.

If you forget to write down the code or use the remote control programming

procedures Aor C... don’t worry!

menu (up) +

menu (down) +

menu (right) +

menu (left) +

SHIFT

menu (up)

menu (down)

menu (right)

menu (left)

brightness (-) red

brightness (+) green

color (-) yellow

color (+) blue

brightness (-) + red

brightness (+) + green

color (-) + yellow

color (+) + blue

1-/--

OK AV

COLOURED

BUTTONS

NOTE :

You cannot use the additional commands unless these were already available on your

original remote control.

REV RIV TUPO CANCEL –+–+–+

TP OFF TP ON FULL EXP EXP ALTO

TIME ORA MEM F MEM TOT TOP BOT I-II

XXX *MENU MENU ●015 014 014 ●015 AV 027 028 027

MIX 10 11

030 058 059

Original remote control / GumBody

additional functions symbols or numbers

▼

▼▼

▼

■❙❙

▼

▼ ▼

3.FOR THE LESSER-USED FUNCTIONS, refer to the code book appendix.

Find the symbol table corresponding to the code you saved to program the remote control.

Locate the additional function you require and note down the symbol or number which

appears below it. EXAMPLE: XXX CODE TABLE

There are 4 ways to enable the additional commands:

A - TV function example:

(a – CANCEL ORA)

A symbol appears beneath the function.

a) the symbol is on your remote control.

(b - brightness +)

b) the symbol is not on your remote control. Find it as indicated

in the drawing. Every symbol is allocated a colour button.

Press the button to transmit the function to the TV. The commands stops when you

release the button.

B - TV function example:

(a – FULL TOT)

A symbol against a grey background appears beneath the

function.

a) the symbol is on your remote control.

(b - sleep)

b) the symbol is not on your remote control. Find it as indicated

in the drawing.

Press SHIFT and the button at the same time. The corresponding function is transmitted to the TV

and stops when you release the button.

C – TV function example:

EXP BOT

A number appears beneath the function (028).

Press and hold down SHIFT.

Type in the number, holding down the last digit (8).

The function is transmitted to the TV and stops when you release

the two buttons (SHIFT+ 8).

D – TV function example:

contrast +

Both a symbol and a number are displayed beneath the function.

You can apply the command using either the symbol or the

number.

If the symbol is not on the remote control, use the number

following the example Cabove.

INFO-LINE

If you have any queries about Facile:

•read this booklet carefully, this will help you to solve almost all problems

•consult our Internet site www.meliconi.it to answer all your queries more easily and quickly.

WARRANTY: 2 years

Tampering or improper product use will void this

guarantee.

Type of remote control Facile

Remote control model GumBody

Purchase date

Agent’s stamp

TROUBLESHOOTING

PROBLEM

The TV does not respond and the light

indicator does not light up when you

press a button.

The TV or VCR does not respond but the

light indicator lights up.

The light indicator flashes.

The remote control commands are not all

working correcting.

The code for your TV make is not in the

Code Book.

SOLUTION

Try some of the other frequently used buttons.

If the problem persists, check that the

batteries are fitted correctly.

If necessary replace them

with 2 new 1.5 V AAA/LR03

alkaline batteries.

Check that the batteries are new

and that the remote control is

pointing at the appliance without any

obstacles in the way. If required,

reset the remote control code,

following the programming

procedure Aor Bor C.

The batteries are low. Change them.

You may have used the wrong

code. Reset the remote control code,

following the programming

procedure Aor Bor C.

Set the remote control code,

following the global search

programming procedure C.

MELICONI Facile User manual

MELICONI Facile User manual

MELICONI Facile User manual

Related papers

Other documents