Panasonic WVBM1910 Operating instructions
- Type
- Operating instructions
Video Monitor
WV-BM1910
Before attempting to connect or operate this product, please read these instructions completely
ENGLISHDEUTSCH
FRANÇAIS
ESPAÑOL
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not
be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the
apparatus.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to per-
sons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the appliance.
Power disconnection. Unit with or without
ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into
the power source; however, the unit is opera-
tional only when the ON-OFF switch is in the
ON position. The power cord is the main
power disconnect for all units.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS APPARATUS MUST BE EARTHED.
To ensure safe operation the three-pin plug supplied must be inserted
only into a standard three-pin power point which is effectively earthed
through the normal household wiring. Extension cords used with the
equipment must be three-core and be correctly wired to provide con-
nection to earth. Wrongly wired extension cords are a major cause of
fatalities.
The fact that the equipment operates satisfactorily does not imply that
the power point is earthed and that the installation is completely safe.
For your safety, if in any doubt about the effective earthing of the power
point, consult a qualified electrician.
For Australia
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT
CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for
your safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replace-
ment fuse has a rating of 5 amp and that it is approved by ASTA or
BSI to BS1362.
Check for the ASTA mark
H or the BSI mark G on the body of
the fuse.
If the plug contains a removable fuse cover you must ensure that it is
refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replace-
ment cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFE-
LY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE
CUT OFF PLUG IS INSERTED INTO ANY 5 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown
below.
If in any doubt please consult a qualified electrician.
WARNING: This apparatus must be earthed.
IMPORTANT
The wires in this mains lead are coloured in accordance with the fol-
lowing code.
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected
to the terminal in the plug which is marked with the letter E or by the
earth symbol
I or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal
in the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the termi-
nal in the plug which is marked with
the letter L or coloured red.
How to replace the fuse
Open the fuse compartment with
a screwdriver and replace the fuse
and fuse cover.
For U.K.
Wij verklaren als enige aansprakelijke, dat het product waarop deze
verklaring betrekking heeft, voldoet aan de volgende normen of
andere normatiefve dokumenten, overeenkomstig de bepalingen van
Richtlijnen 73/23/EEC en 89/336/EEC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne dekla-
ration omhandler, er i overensstemmelse med den følgende stan-
darder eller andre normative dokumenter i følge bestemmelserne i
direktivene 73/23/EEC og 89/336/EEC.
Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken
denna deklaration hänvisar är i överensstämmelse med standard-
dokument, eller andra normativa dokument som framstölls i Direktiv
73/23/EEC och 89/336/EEC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoi-
tus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asi-
akirjoja, jotka noudattavat direktiivien 73/23/EEC ia 89/336/EEC.
säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne erklærin-
gen gjelder for, er i overensstemmelse med følgende normer eller
andre normgivende dokumenter som fælger bestemmelsene i direk-
tiven 73/23/EEC og 89/336/EEC.
We declare under our sole responsibility that the product to which this
declaration relates is in conformity with the standards or other norma-
tive documents following the provisions of Directives EEC/73/23 and
EEC/89/336.
Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a
cui si riferisce la presente dichiarazione risulta conforme ai seguenti
standard o altri documenti normativi conformi alle disposizioni delle
direttive CEE/73/23 e CEE/89/336.
The serial number of this product may be found on the rear
of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of
your purchase to aid identification in the event of theft.
Model No. WV-BM1910
Serial No.
ENGLISH VERSION
-1-
The Panasonic WV-BM1910 Video Monitor is a desk-top
closed circuit Video Monitor especially designed for
surveillance and studio applications.
This monitor features a 473 mm (18-5/8”) actual
diagonal viewing size screen and produces sharp,
• Refer all work related to the installation of this
product to qualified service personnel or system
installers.
• Do not block the ventilation opening or slots on
the cover.
To prevent the appliance from overheating, place
the monitor at least 5 cm (2 inches) away from the
wall.
• Do not drop metallic parts through slots.
This could permanently damage the appliance.
Turn the power off immediately and contact quali-
fied service personnel for service.
• Do not attempt to disassemble the appliance.
To prevent electric shock, do not remove screws or
covers.
There are no user-serviceable parts inside. Contact
qualified service personnel for maintenance.
•Handle the appliance with care.
Do not strike or shake, as this may damage the
appliance.
• Do not expose the appliance to water or
moisture, nor try to operate it in wet areas.
Do take immediate action if the appliance becomes
wet. Turn the power off and refer servicing to quali-
fied service personnel. Moisture may damage the
appliance and also cause electric shock.
•Do not use strong or abrasive detergents when
cleaning the appliance body.
Use a dry cloth to clean the appliance when it is
dirty.
When the dirt is hard to remove, use a mild deter-
gent and wipe gently.
• Do not operate the appliance beyond its spe-
cified temperature, humidity or power source
ratings.
Use the appliance at temperatures within –10°C to
+50°C (14°F to 122°F) and a humidity below 90 %.
The input power source for this appliance is 220 -
240 V AC 50 Hz.
PREFACE
• 473 mm (18-5/8”) actual diagonal viewing size.
• Horizontal resolution is 1 000 lines at centre of
screen.
• Under or normal scan size (switchable).
FEATURES
PRECAUTIONS
black-and-white pictures with a horizontal resolution of
1 000 lines at centre.
The WV-BM1910 can be used with other CCTV
monitors or Panasonic Video Tape Recorders.
CONTENTS
PREFACE .................................................................................................................................................................................. 1
FEATURES ................................................................................................................................................................................ 1
PRECAUTIONS ......................................................................................................................................................................... 1
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ................................................................................................... 2
CONNECTIONS ........................................................................................................................................................................ 4
SYSTEM CONNECTIONS ......................................................................................................................................................... 4
ADJUSTMENT .......................................................................................................................................................................... 5
OPERATION ............................................................................................................................................................................. 5
SPECIFICATIONS ..................................................................................................................................................................... 6
STANDARD ACCESSORY ........................................................................................................................................................ 6
ENGLISH
-2-
■ FRONT VIEW
1. Power On/Off Switch (POWER ON/OFF)
This switch turns the power of the monitor on and
off.
Press this switch once to turn (switch down ;) the
power of the monitor on.
Press again (switch up l) for turn the power of the
monitor off.
2. Power Indicator
This indicator lights to indicate that the power is on.
3. Scan Size Selection Switch (SCAN SIZE, UNDER/
NORMAL)
This switch is used for selecting the scan size.
Press once (switch down ;) to select the Under
Scan mode.
Press again (switch up l) to select the Normal
Scan mode.
4. Horizontal Hold Control (H. HOLD)
This control is used to lock the horizontal position of
the picture.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
POWER
SCAN
SIZE
V.HOLD
HEIGHT
NORMAL
UNDER
OFF
ON
BRIGHT CONTRAST
H.HOLD V.LIN
Video Monitor WV-BM
5. Vertical Hold Control (V. HOLD)
This control is used to lock the vertical position of
the picture.
6. Height Control (HEIGHT)
This control is used to adjust the height of the
picture.
7. Bright Control (BRIGHT)
Turn this control clockwise to increase the picture
brightness.
Turn this control counterclockwise to decrease the
picture brightness.
8. Vertical Linearity Control (V. LIN)
This control is used to correct the vertical
nonlinearities in the picture.
9. Contrast Control (CONTRAST)
Turn this control clockwise to increase the picture
contrast.
Turn this control counterclockwise to decrease the
picture contrast.
-3-
10. Video Output Connector (VIDEO OUT)
This BNC type connector is used to provide the
video output signal of the source to an additional
monitor or video tape recorder.
11. Video Input Connector (VIDEO IN)
This BNC type connector is used for receiving the
video signal from a source to be monitored, such as
a VTR.
12. DC Restoration Switch (DC REST ON/OFF)
Select ON or OFF to restore background of picture
or not.
13. AC IN
■ REAR VIEW
AC INDC REST
OFF
IN
ON
OUT
VIDEO
-4-
Power Cord
1. Keep the Power ON/OFF switch of the camera in
the OFF position during installation.
2. Connect the Power Cord to a grounded electrical
outlet.
Video Cable
Use a 75 Ω coaxial cable (RG-59, RG-59A/U, RG-
59B/U, RG-59/U, RG-6/U, or RG-11/U).
1. Up to 10 monitors can be hooked up in this
configuration before signal loss occurs. Total cable
length should not be longer than 150 meters (500
feet).
2. Wiring Precautions :
Do not bend the coaxial cable into a curve whose
radius is smaller than 10 times its diameter.
Never staple coaxial cables, not even with circular
staples.
Never crush or pinch the cable.
All of the above will change the impedance of the
cable and cause poor picture quality.
CONNECTIONS
1. Single Monitor Connection
OUT
VIDEO
IN
ONOFF
• Connect the Video Input Connector (VIDEO IN) on
this monitor to the Video Output Connector of the
video source with a coaxial cable.
2. Multiple Monitor Connection
• Connect the Video Input Connector (VIDEO IN) on
this monitor to the Video Output Connector of the
video source with a coaxial cable.
• Connect the Video Output Connector (VIDEO OUT)
on this monitor to the Video Input Connector
(VIDEO IN) on the second monitor with a coaxial
cable.
• Complete the connections of all monitors in the
system according to the above procedure.
OUT
VIDEO
IN
OUT
VIDEO
IN
Coax.
Cable
TV Camera
WV-BM1910
Coax.
Cable
Coax. Cable
TV Cameras
First Video
Monitor
Last Video Monitor
Video Switcher
SYSTEM CONNECTIONS
-5-
Preparations:
Make sure that all required connections in the system
are completed.
Turn on the power of this monitor by pressing the Power
On/Off Switch on the front panel.
1. Adjust the brightness by the Bright Control
(BRIGHT) and the Contrast Control (CONTRAST) so
that the overall brightness is appropriate and grey
tones are resolved.
2. If the picture slips to either side, or a series of
horizontal lines appear, adjust the Horizontal Hold
Control (H.HOLD) until the picture is stabilized.
3. If the picture rolls up or down, adjust the Vertical
Hold Control (V.HOLD) until the picture is stabilized.
4. The sub controls, HEIGHT and V. LINEARITY,
should be adjusted at the same time to give proper
vertical height consistent with good vertical
linearity. Extending the picture height approximately
6 mm (1/4”) beyond the top and bottom edges of
the CRT mask is recommended.
Under Scanning
Press the Scan Size Selection Switch (SCAN SIZE)
once (switch down ;) to set the UNDER position.
DC Restoration
DC restoration circuit provides a stable reference for
the black level.
Set the switch to ON to prevent excessive contrast and
preserve shadow detail.
POWER
ON
OFF
BRIGHT CONTRAST
H.HOLD
OFF ON
V.HOLD
NORMAL
UNDER
SCAN
SIZE
increaseincrease
HEIGHT V. LIN
Press again (switch up l) to NORMAL position.
ADJUSTMENT
OPERATION
-6-
Power Source : 220 - 240 V AC, 50 Hz
Power Consumption : Approx. 47 W
Video Input : 1.0 V[p-p] CCIR composite/75 Ω x 1
Video Output: Looping through VIDEO IN connector x 1
Horizontal Resolution : 1 000 TV lines at centre
Sweep Linearity : Less than 5 % at overscan
Sweep Geometry : Less than 2 % at overscan
Overscanning : Approx. 6 %
Scanning Size : Normal or underscan, selectable
Tube Size : 473 mm (18-5/8”) diagonal actual visual size
505 mm (19-7/8”) diagonal tube screen size
Ambient Operating Temperature : −10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity : Less than 90 %
Dimensions : 483(W) X 443(H) X 329(D) mm
19-1/32”(W) X 17-7/16”(H) X 12-31/32”(D)
Weight : 20 kg (44 lbs.)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
Power Cord ............................................................. 1 pc.
SPECIFICATIONS
STANDARD ACCESSORY
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/
Np1098-2102 YWV8QA5040CN Printed in Philippines
N 30 Gedruckt in den Philippinen
Imprimé aux Philippines
Impreso en Filipinas
1998 © Matsushita Communication Industrial Co., Ltd. All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Panasonic WVBM1910 Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Panasonic TH42PA50EY Owner's manual
-
-
-
-
-
-
-
-
-
