DeWalt DE7400 User manual

Category
Circular saws
Type
User manual
2
Dansk 4
Deutsch 9
English (original) 15
Español 20
Français 26
Italiano 32
Nederlands 38
Norsk 44
Português 49
Suomi 55
Svenska 60
Türkçe 65
 71
Copyright DEWALT
ENGLISH
15
HEAVY-DUTY ROLLING TABLE SAW STAND
DE7400
Congratulations!
You have chosen a DEWALT tool. Years of
experience, thorough product development and
innovation make DEWALT one of the most reliable
partners for professional power tool users.
Technical Data
DE7400
Length mm 910
Height mm 830
Maximum working load kg 68
Weight kg 15.5
Defi nitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert
symbol indicates a potentially hazardous
situation which, if not avoided, may
result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Declaration of Conformity
DE7400
DEWALT declares that this product described under
“technical data” have been designed in compliance
with applicable technical rules.
For more information, please contact D
EWALT at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
D
EWALT.
Horst Grossmann
Vice President Engineering and Product
Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
04.08.08
WARNING: For your own safety, read
the table saw instruction manual before
using any accessory. Failure to heed
these warnings may result in personal
injury and serious damage to the table
saw and the accessory. When servicing
this tool, use only identical replacement
parts.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
General Safety Instructions for Table
Saw Accessories
WARNING: To reduce the risk of
personal injury:
Ensure all stand fasteners are
securely fastened and that all stand
mechanisms are in proper working
order before operating the table saw.
DO NOT exceed the weight this
stand can hold. The DE7400 table
saw stand is designed to support
68 kgs. (150 lbs.) safely in a work
environment. It is unsafe to climb, sit
or stand on the stand.
Follow the mounting instructions
carefully. Fasten the tool to the
saw mounting brackets securely as
instructed.
DO NOT modify or use stand for
operations for which it is unintended.
ENGLISH
16
DO NOT use the stand on uneven
surfaces. DO NOT use the stand with
the legs folded and stand sitting on
the ground. The stand is designed to
be used on a flat, stable surface.
Package Contents
The package contains:
1 Stand
2 Carriage head bolts
2 Mounting brackets
4 M8 lock nuts
2 Wheels
1 Rear axle
2 Rubber bumpers
2 M4 screws
4 Washers
2 M4 lock nuts
1 Kickstand assembly
2 Tube plugs
M6 screws (4)
M4 hex wrench
Saw mounting hardware:
4 hex head bolts
8 washers
4 nuts
4 lock washers
1 Instruction manual
Check for damage to the tool, parts or
accessories which may have occurred during
transport.
Take the time to thoroughly read and
understand this manual prior to operation.
Description (fi g. 1A, 1B)
WARNING: Never modify the accessory
or any part of it. Damage or personal
injury could result.
NOTE: Figure 1B shows the front of the DE7400.
a. Axle
b. Leg supports
c. Wheels
d. Saw mounting bracket
e. Bracket release levers
f. Leg release levers
g. Locking pins
h. Legs
i. Beams
j. Locator clip
k. Handle
l. Handle lock
m. Rubber bumpers
n. Kickstand
o. Tube plugs
INTENDED USE
This rolling table saw stand is designed for use with
DEWALT DW744 and DW745 table saws only. If
you have any problem with alignment or mounting,
consult an authorised DEWALT repair agent.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
ASSEMBLY
Attaching the Wheels and Axle
(fi g. 1, 2)
1. Attach the axle (a) to the leg support (b) by
aligning the pre-drilled holes. Ensure the long
end of the axle is to the rear of the stand as
shown. Secure axle to leg support using two
carriage bolts, washers and lock nuts provided.
2. Place the wheels (c) on the axle and secure with
washers and lock nuts as shown. Tighten wheel
and axle nuts securely.
Attaching the Kickstand (fi g. 3–5)
Insert the tube plugs (o) into the end of the kickstand
(n). The groove in the tube plug should be facing
down as shown. Be sure that the holes (p) in
the tube plugs are in line with the holes (q) in the
kickstand tube before inserting the tube plugs.
Insert the kickstand (n) through the holes in the leg
support (b) on the wheel-axle side of the stand. Be
sure the kickstand is pointing up when the stand
is an upright position. Secure the kickstand to the
beams (i) with the four M6 screws provided.
The hex wrench may be stored in the end of the
tube plug as shown for future use.
ENGLISH
17
Attaching the Rubber Bumpers
(fi g. 6)
Attach the two rubber bumpers (m) to the handle
side leg support as shown using the screws and
lock nuts provided.
Table Saw Bracket Mounting
(fi g. 7–10)
WARNING: To reduce the risk of
injury, turn unit off, disconnect
machine from power source before
assembling the table saw to the
table saw stand. An accidental start-
up can cause injury.
WARNING: For your own safety,
read and understand the table saw
instruction manual before using. Failure
to heed these warnings may result in
personal injury and serious damage to
the table saw and the accessory.
WARNING: The saw mounting brackets
provided with this stand are equipped
with lever locks. To reduce the risk of
injury, DO NOT modify the mounting
bracket lever locks.
1. Unfold the legs (h) by depressing the leg release
levers (f). Rotate the legs until the locking pin (g)
clicks into its detent (r).
2. Turn the stand upright. The stand should be
stable and should not rock.
WARNING: Be sure that the locking
pins have engaged and the legs are
firmly held in place.
IMPORTANT: The mounting brackets MUST be
attached with the arrows facing the front of the
stand as shown in figure 1B.
3. The locator clip (j) keeps the saw from sliding
left or right during cutting operations and during
transport. Install the mounting brackets on to
the beam as shown by engaging the concave
front lip of the mounting bracket with the
rounded front edge of the beam. One of the
brackets must engage the locator clip (j). The
mounting bracket release levers (e) must be
positioned to the rear of the stand as shown.
4. Measure the distance between the mounting
holes of the table saw. Position the second
mounting bracket onto the beam at this
distance from the first mounting bracket.
5. Align the holes in the table saw base with the
slots in the saw mounting brackets (d).
6. Feed a hex head bolt with flat washer installed
through each of the four holes in the table saw
base and mounting brackets. Secure each
location with a flat washer, lock washer and nut
provided.
WARNING: To reduce the risk of
personal injury, be sure the table saw is
fully anchored on the stand.
WARNING: The table saw must
be positioned on the tool mount so
that all four corners can be bolted
to the mounting brackets. If the saw
is mounted properly, the mounting
brackets will be positioned perpendicular
to the stand rail when the saw is placed
on the stand.
For additional questions or clarification on the above
instructions, consult an authorised DEWALT repair
agent.
To Detach the Saw from the Stand
(fi g. 11, 12)
WARNING: To reduce the risk of
injury, turn unit off, disconnect
machine from power source before
detaching the table saw from the
table saw stand. An accidental start-
up can cause injury.
The saw mounting brackets included with the
DE7400 stand are equipped with rubber feet that
can support the saw when cutting on a work area
without a stand.
TO REMOVE THE SAW FOR CARRYING OR FOR USE
WITHOUT THE STAND
1. Reach around the sides of the saw and grasp
the release levers (e).
2. Pull up slightly to clear the beam and tilt the saw
toward you to carry.
TO REATTACH THE SAW AND SAW MOUNTING BRACKETS
TO THE STAND
1. Grip the table saw table as shown while facing
the front of the saw.
2. Position the left-hand side mounting bracket
into the locator clip.
3. When the front concave lip of both mounting
brackets are engaged with the front round edge
of the beam, pivot the saw back and down
allowing the release levers (e) to click into place
on the rear beam. Rock the saw gently to verify
the mounting brackets are locked onto the
beams.
ENGLISH
18
4. If the handle (k) has been extended, pull the
handle lock (l) down to release the handle and
then slide the handle in for storage or saw
usage.
TO ATTACH DEWALT DW745 TABLE SAW TO
SAW MOUNTING BRACKETS
1. Remove the front feet bolts and the front rubber
feet from the DW745 table saw.
2. Remove the rear feet from the rear frame bar of
the saw.
3. Retain these components for future use.
4. Feed a hex head bolt with flat washer installed
through each of the four holes in the frame bars
where the removed front and rear feet were
previously installed. Secure each location with a
flat washer, lock washer and nut provided.
WARNING: To reduce the risk of
personal injury, NEVER use the table
saw with the handle extended. An
extended handle creates an unsafe work
area.
WARNING: To reduce the risk of
personal injury, do not hang objects
from the handle. The stand may tip
when downward force is applied.
Transporting the Saw on the Stand
(fi g. 13)
COLLAPSING THE STAND FOR TRANSPORT
1. Place one hand under the leg support (b) and
hold the legs (h) slightly off the ground.
2. Depress the leg release lever (f) with the other
hand then push the leg under the beam on the
stand. Repeat the operation on the second leg
of the stand and rest the stand on wheels.
3. Repeat with the other end of the stand.
4. Pull the extendable handle (k) out of the side of
the stand. The spring-loaded handle lock (l) will
lock the handle into position for transporting the
saw on the stand. Pull the handle lock down to
release the handle and then slide the handle in
for storage.
WARNING: To reduce the risk of
personal injury, DO NOT operate the
table saw mounted to the stand with the
legs folded and the stand sitting on the
ground.
WARNING: To reduce the risk of
personal injury, DO NOT attempt to
store the stand – with or without the
saw attached – in a vertical position.
Loss of control may result.
To Raise Stand from Collapsed
Position
Roll the stand to the workspace. Be sure the area is
flat and stable before attempting to set up the saw
and stand.
1. Tilt up the stand until the saw is at a 45-degree
angle.
2. Depress the leg release levers one at a time to
release the locking pins and pull the front legs
out until each locking pin clicks into the detent.
WARNING: Be sure that the locking
pins have engaged and the legs are
firmly held in place.
3. Rest the stand on the legs.
4. Depress the handle lock (l) to release the
handle. Slide the handle (k) into the leg support
(b) for storage as you work.
5. Go to the opposite side of the stand and grasp
the saw under the rear axle. Lift the saw and
stand.
6. Reach under the stand and, one at a time,
depress the leg release levers to release the
locking pins. Pull out the remaining two legs. Be
sure that the locking pins have engaged and the
legs are firmly held in place. Rest the stand on
the ground.
MAINTENANCE
Your DEWALT accessory has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off, disconnect
machine from power source before
detaching the table saw from the
table saw stand. An accidental start-
up can cause injury.
ENGLISH
19
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have not
been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of serious
injury, place stand on flat, stable surface.
DO NOT create unstable conditions.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your D
EWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
GUARANTEE
30 DAY NO RISK
SATISFACTION GUARANTEE
If you are not completely satisfied with
the performance of your D
EWALT tool,
simply return it within 30 days, complete as
purchased, to the point of purchase, for a full
refund or exchange. Proof of purchase must
be produced.
ONE YEAR FREE SERVICE CONTRACT
If you need maintenance or service for your
D
EWALT tool, in the 12 months following
purchase, it will be undertaken free of charge
at an authorised D
EWALT repair agent. Proof
of purchase must be produced. Includes
labour and spare parts for Power Tools.
Excludes accessories.
ONE YEAR FULL WARRANTY
If your DEWALT product becomes defective
due to faulty materials or workmanship within
12 months from the date of purchase, we
guarantee to replace all defective parts free of
charge or, at our discretion, replace the unit
free of charge provided that:
The product has not been misused.
Repairs have not been attempted by
unauthorised persons.
Proof of purchase date is produced. This
guarantee is offered as an extra benefit
and is additional to consumers statutory
rights.
For the location of your nearest authorised
DEWALT repair agent, please use the
appropriate telephone number on the back of
this manual. Alternatively, a list of authorised
DEWALT repair agents and full details on our
after-sales service are available on the Internet
at www.2helpU.com.
Belgique et Luxembourg Black & Decker - DEWALT Tel: +32 (0)015 - 15 47 9211
België en Luxemburg Nieuwlandlaan 7, IZ Aarschot B156 Fax: +32 (0)015 - 15 47 9210
B-3200 Aarschot www.dewalt.be
Danmark D
EWALT Tlf: 70201511
Sluseholmen 2-4 Fax: 70224910
2450 København SV www.dewalt.dk
Deutschland D
EWALT Tel: 06126-21-1
Richard-Klinger-Straße Fax: 06126-21-2770
65510 Idstein www.dewalt.de
 Black & Decker (Hellas) S.A. Τηλ: (01) 8981-616
Στράβωνος 7 & Βουλιαγμένης 159 Φαξ: (01) 8983-570
Γλυφάδα 16674, Αθήνα Service: (01) 8982-630
España D
EWALT Tel: 934 797 400
Parque de Negocios “Mas Blau” Fax: 934 797 439
Edificio Muntadas, c/Bergadá, 1, Of. A6 www.dewalt.es
08820 El Prat de Llobregat (Barcelona)
France D
EWALT Tel: 472 20 39 72
Le Paisy Fax: 472 20 39 02
BP 21, 69571 Dardilly Cedex www.dewalt.fr
Schweiz D
EWALT Tel: 01 - 730 67 47
Suisse In der Luberzen 40 Fax: 01 - 730 70 67
Svizzera 8902 Urdorf www.dewalt.ch
Ireland D
EWALT Tel: 00353-2781800
Calpe House Rock Hill Fax: 00353-2781811
Black Rock, Co. Dublin www.dewalt.ie
Italia D
EWALT Tel: 800-014353
Viale Elvezia 2 Fax: 039-2387592
20052 Monza (Mi) www.dewalt.it
Nederlands Black & Decker - D
EWALT Tel: 0164 283000
Joulehof 12 Fax: 0164 283100
4600 AB Bergen Op Zoom www.dewalt.nl
Norge D
EWALT Tel: 22 90 99 00
Postboks 4814, Nydalen Fax: 22 90 99 01
0422 Oslo www.dewalt.no
Österreich D
EWALT Tel: 01 - 66116 - 0
Werkzeugevertriebs GmbH Fax: 01 - 66116 - 14
Erlaaerstraße 165, Postfach 320,1231 Wien www.dewalt.at
Portugal D
EWALT Tel: 214 66 75 00
Rua Egas Moniz 173 Fax: 214 66 75 75
João do Estoril, 2766-651 Estoril www.dewalt.pt
Suomi D
EWALT Oy Puh: 010 400 430
Tekniikantie 12 Faksi: 0800 411 340
02150 Espoo, Finland www.dewalt.fi
D
EWALT Oy Tel: 010 400 430
Teknikvägen 12 Fax: 0800 411 340
02150 Esbo, Finland www.dewalt.fi
Sverige D
EWALT Tel: 031 68 61 00
Box 94 Fax: 031 68 60 08
431 22 Mölndal www.dewalt.se
Türkiye
KALE Hırdavat ve Makina A.Ş. Tel: 0212 533 52 55
Defterdar Mah. Savaklar Cad. No:15 Faks: 0212 533 10 05
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE www.dewalt.com.tr
United Kingdom D
EWALT Tel: 01753-56 70 55
210 Bath Road Fax: 01753-57 21 12
Slough, Berks SL1 3YD www.dewalt.co.uk
N019219 10/08
1 / 1

DeWalt DE7400 User manual

Category
Circular saws
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document