![](//vs1.manuzoid.com/store/data-gzf/e8e4ad89fa3c825b9d30c9636221534b/3/000117416.htmlex.zip/bgb.jpg)
10
In COOL or DEHUMIDIFY mode
(1) When the initial temperature is 16°C, the
air conditioner will continue to run at this
setting;
(2) When the initial temperature is set
between 17-20°C, the set temperature
ZLOOGHFUHDVH&DIWHUWKH¿UVWKRXUDQG
continue to run at this setting;
:KHQWKHLQLWLDOWHPSHUDWXUHLVVHW
between 21-27°C, the set temperature
will decrease 1°C in every hour, after two
hours the air conditioner will continue to
run at this setting;
(4) When the initial temperature is set
EHWZHHQ&WKHVHWWHPSHUDWXUH
will decrease 1°C in every hour, after
three hours the air conditioner will
continue to run at this setting;
6OHHSPRGH
In this mode the sleep temperature curve is
manually set.
(1) After selecting Sleep mode
, press and
hold the Turbo button until the remote
FRQWUROHQWHUVLQWRXVHUGH¿QHGVOHHS
setting status. The remote control will
display “1” hour, temperature display will
show the corresponding temperature of
last setting sleep curve and blink (the
original factory setting will display for the
¿UVWXVH
(2) Adjust the control buttons
and
to change the set temperature for the
¿UVWKRXURIVOHHS$IWHUVHWWLQJWKH
temperature, press the Turbo button for
FRQ¿UPDWLRQ
7KHKRXURIVOHHSPRGHZLOOEH
automatically increased on the remote
FRQWUROWRWKHQGUGKRXURIVOHHS
mode and so on with each press of the
Turbo button;
5HSHDWWKHDERYHVWHSRSHUDWLRQ
until 8 hours of sleep temperature setting
LV¿QLVKHG7KHUHPRWHFRQWUROZLOO
resume the original timer display and
the temperature display will return to the
original setting.
The sleep program can be checked by
selecting sleep mode
, pressing and
holding the Turbo button and then repeat
pressing the turbo button to review the sleep
program temperatures without pressing the
control button
or .
In this mode, if no button is pressed for 10
seconds, the display will revert to normal
operation.
,21)LOWHU%XWWRQ
Press this button to turn on and off the Cold
Plasma function and Plasma Dust Collector
function.
symbol will be displayed on the remote
control if Cold Plasma function and Plasma
Dust Collector function are selected.
,)HHO%XWWRQ
Press this button to turn on the I Feel
function and the symbol
will be displayed
on the remote control.
The remote control will send the temperature
information to the indoor unit every ten (10)
minutes. The air conditioner will operate to
reach the set temperature at the location of
the remote control.
Press again to cancel this function.
;)DQ%XWWRQ
Press this button in COOL or DEHUMIDIFY
mode to active X-Fan function. The symbol
will be displayed on the remote control.
After the unit is turned off the indoor fan will
continue operation at low fan speed for 10
minutes to dry the indoor unit prevent from
bacteria and mildew growing.
Presss again to cancel this function.
&ORFN%XWWRQ
Press this button and the Clock symbol
will blink. You can press Control buttons
and to set the time you want.
/LJKW%XWWRQ
Press this button to switch the indicating
lights of the indoor unit on or off.
The normal condition at start up is on.
7LPHU2Q%XWWRQ
Press the Timer On button to set the Timer
On or start time,
V\PEROZLOOÀDVKRQWKH
display. Press the control button
or to
adjust the start time.
Press this button again to cancel the Timer
On function, and
symbol will disappear.
&RQ¿UPWKH7LPHU2QVHWWLQJVE\SUHVVLQJ
7LPHU2QEXWWRQRUZDLWIRUVHFRQGVDIWHU
selecting the desired time and the
symbol
will display permanently.
Default time for timer on is 8:00AM.