Lexibook DJ033 User manual

DJ033series

Appareil photo numérique avec ﬂash

Digital Camera with ﬂash

MODE D’EMPLOI – INSTRUCTION MANUAL

DJ033seriesIM1210.indb 1 25/05/2010 6:31

Page is loading ...

English

16

GETTING TO KNOW YOUR CAMERA

1. Shutter/Set button

2. Camera strap holder

3. Camera lens

4. Flash

5. USB connector port/SD card slot

6. Up/Playback button

7. LCD screen

8. LED

9. Power/Menu button

10. Down/Flash button

11. Battery compartment

CONTENTS OF THE PACKAGING

1 x DJ033series digital camera

1 x USB cable

1 x hand strap

1 x installation CD-ROM

1 x instruction manual

WARNING: All packaging materials, such as tape, plastic sheets, wire ties

and tags are not part of this product and should be discarded for your child’s

safety.

INSERTING NEW BATTERIES

1. Make sure the camera is off.

2. Using a screwdriver, open the battery compartment

cover located at the base of the unit.

3. Insert 2 x LR03/AAA 1,5V type batteries (not

included) observing the polarity indicated at the

bottom of the battery compartment, and as per the

diagram shown opposite.

4. Close the battery compartment and tighten the screw.

Non-rechargeable batteries are not to be recharged. Rechargeable batteries

are to be removed from the product before being charged. Rechargeable

batteries are only to be charged under adult supervision. Different types of

batteries or new and used batteries are not to be mixed. Only batteries of the

same or equivalent type as recommended are to be used. Batteries are to be

inserted with the correct polarity. Exhausted batteries are to be removed from

the product. The supply terminals are not to be short circuited. Do not throw

batteries into a re. Remove the batteries if you are not going to use the product

for a long period of time.

DJ033seriesIM1210.indb 16 25/05/2010 6:31

English

17

WARNING: Malfunction or loss of memory may be caused by strong

frequency interference or electrostatic discharge. Should any abnormal

function occur, remove the batteries and insert them again.

IMPORTANT NOTE: All the les stored into the unit’s internal memory will

be lost when switching off the camera or replacing the batteries. Make sure

you transfer the les to your computer before turning off the product or

changing the batteries.

INSTALLING AN OPTIONAL MEMORY CARD

You need to insert an SD card (8GB maximum, not included) so you can

store your les. To do so, push the SD card rmly into the slot until you hear

a ‘click’ sound. The icon will be displayed after inserting an SD card and

powering the unit on.

Note:

When an external memory card has been inserted in the camera, all

the images taken will be stored on the external memory card.

IMPORTANT NOTE:

It is highly recommended to add a SD card to increase

the storage capacity of the unit.

Follow these instructions to install the camera driver on your computer system.

1. Insert the CD Software (included) in your CD-ROM drive. The CD will

auto run, and the main menu will appear.

2. Click “Install Driver”, and then follow the instructions to install the camera

driver.

3. You will need to reboot your computer after the driver installation.

4. Click ‘ArcSoft MediaImpression’, and the ‘Choose Setup Language’

screen will appear. Select your language and click ‘OK’. Follow the

instructions to install ‘ArcSoft MediaImpression’ on your computer

system. The software offers many applications for photo editing and printing.

5. Once you have nished installing, please restart the computer.

Note:

• If the CD does not auto run, click ‘Start’, ‘Run’, then type in ‘D:\autorun.

exe’ in the Run dialog text box (where D:\ is your CD-ROM drive) and

press Enter.

• You must install the driver before downloading photos/videos from the

camera or using it as a webcam.

• Make sure the camera is not connected to your computer before installing

the driver and the software.

INSTALLING THE SOFTWARE AND THE CAMERA DRIVER

DJ033seriesIM1210.indb 17 25/05/2010 6:31

English

18

1. Press the Power button (9) for about 3 seconds to turn the camera on.

The LED will light up for a moment and the camera will sound a beep to

conrm that it is ready for use.

2. Press and hold the Power button (9) for about 3 seconds again to turn it off.

Note: The camera will auto power off after a few seconds of inactivity.

TURNING THE CAMERA ON AND OFF

You are already in camera mode when you switch on the unit:

1. Press the Shutter button (1) to take a photo. The camera will beep twice

to conrm that a picture is taken.

2. To check the number of pictures you have left to take, the battery level

or resolution, press the Menu button (9) once in camera mode. Wait a

few seconds to automatically go back to the camera mode.

Note:

• When the camera’s built-in memory is full, if you try to take a photo, the

LCD screen will display a warning message.

• When the SD card inserted in the camera is full, you will not be able to

take new photos. Make sure you transfer all your photos to your computer.

TAKING PHOTOS

Switch on the camera:

Auto ash

1. In camera mode, press the Down/Flash button (10) until the icon

appears on the lower left corner of the LCD screen. The auto ash

function will be activated.

Flash on

2. In camera mode, press the Down/Flash button (10) until the icon

appears on the lower left corner of the LCD screen. The ash function will

be activated.

Flash on

3. In camera mode, press the Down/Flash button (10) until the icon

appears on the lower left corner of the LCD screen. The ash function will

be disabled.

FLASH FUNCTION

DJ033seriesIM1210.indb 18 25/05/2010 6:31

English

19

1. In camera mode, press the Menu button (9) to enter the settings menu

(the battery level, resolution, photo quality and the number of

photos/videos left to take are displayed on the screen).

2. Press the Down/Flash button (10) once, the ‘Resolution’ icon

appears.

3. Press the Up/Playback button (6) repeatedly to select the desired

resolution, then press the Down/Flash button (10) to conrm your choice.

There are 3 resolution modes:

Normal resolution (1280 x 1024 pixels).

VGA resolution (640 x 480 pixels).

QVGA resolution (320 x 240 pixels)

SELECTING THE PHOTO RESOLUTION

SELECTING THE PHOTO QUALITY

1. In camera mode, press the Menu button (9) to enter the settings menu

(the battery level, resolution, photo quality and the number of

photos/videos left to take are displayed on the screen).

2. Press the Down/Flash button (10) and then the Menu button (9) until the

‘Picture Quality’ icon appears.

3. Use the Up/Playback button (6) to select the HQ (High Quality) or SQ

(Standard Quality).

4. Press the Down/Flash button (10) to conrm your choice.

SELECTING THE PC CAMERA OR USB PHOTO

1. In camera mode, press the Menu button (9) to enter the settings menu

(the battery level, resolution, photo quality and the number of

photos/videos left to take are displayed on the screen).

2. Press the Down/Flash button (10) and then the Menu button (9) until the

‘USB’ icon appears.

3. Use the Up/Playback button (6) to select the USB mode or the

Webcam mode .

4. Press the Down/Flash button (10) to conrm your choice.

DJ033seriesIM1210.indb 19 25/05/2010 6:31

English

20

SELECTING THE CAMERA FREQUENCY

A higher frequency increases the camera shutter speed so the effect of light

uctuations from sources such as orescent lamps are reduced.

1. In camera mode, press the Menu button (9) to enter the settings menu

(the battery level, resolution, photo quality and the number of

photos/videos left to take are displayed on the screen).

2. Press the Down/Flash button (10) and then the Menu button (9) until the

‘Frequency’ icon appears.

3. Use the Up/Playback button (6) to select the 50Hz or 60Hz.

4. Press the Down/Flash button (10) to conrm your choice.

SELF-TIMER (CAMERA MODE ONLY)

1. In camera mode, press the Menu button (9) to enter the settings menu.

2. Press the Menu button (9) until the ‘Video’ icon appears, then press

the Shutter button (1) within 5 seconds to start the video capture.

3. Press the Shutter button (1) again to stop the video capture and save it in

AVI format.

Note:

• The ash function is disabled in video mode.

• To watch the videos, you must transfer them to your computer (see the

‘Downloading your photos and your videos’).

• The videos will be saved in AVI format. You can use Media player and

Quick time to play them (there is no sound for the video clips).

• The video clips’ length may change according to the memory space avail

able on the camera’s built-in memory or on the SD card.

TAKING 3 PHOTOS IN RAPID SUCCESSION

1. In camera mode, press the Menu button (9) to enter the settings menu.

2. Press the Menu button (9) until the ‘3 shots’ icon appears.

3. Press the Shutter button (1) within 5 seconds to start taking the photos.

The camera will then take 3 photos in rapid succession and beep each

time a photo has been taken.

DJ033seriesIM1210.indb 20 25/05/2010 6:31

English

21

PLAYBACK MODE

1. Switch on the unit. In camera mode, press the Up/Playback button (6) to

enter playback mode.

2. Use the Down/Flash (10) button to display the next or the previous photo.

3. To exit the playback mode, press the Up/Playback button (6) at any time.

Note:

• If there are no pictures stored in the camera’s built-in memory or in the SD

card, the playback mode is not available.

• The videos cannot be played in playback mode.

Deleting one le

1. In playback mode, use the Down/Flash (10) button to display the desired

photo or video.

2. Press the Menu button (9), the icon will appear on the LCD screen.

3. Use the Down/Flash (10) button to select ‘delete’ (√) or ‘do not delete’ (X).

4. Press the Shutter button (1) to conrm the deletion.

Note: To cancel the deletion, press the Up/Playback button (6) at step 2 or 3.

Deleting all les

1. In playback mode, press the Power button (9) until the icon appears,

then press the Shutter button (1).

2. Use the Down/Flash (10) button to select ‘delete’ (√) or ‘do not delete’ (X).

3. Press the Shutter button (1) to conrm the deletion of all les.

Note: To cancel the deletion, at step 2 or 3, press the Up/Playback button (6).

DOWNLOADING YOUR PHOTOS AND YOUR VIDEOS

To download your photos and videos, the camera must be in USB

mode.

Manual downloading

1. Connect the camera to your computer via the USB cable provided.

2. Click the ‘Start’ button in Windows.

3. Click the ‘My computer’ icon.

4. Click ‘Removable Disk’, then ‘DCIM’ to view the les stored on your SD

card. Your photos and videos are stored in a subfolder called

‘100IMAGEDCIM’.

5. You can copy and paste them into any directory you choose.

DJ033seriesIM1210.indb 21 25/05/2010 6:31

English

22

WEBCAM MODE

Connected to your PC, your camera can be used as a webcam.

Note: the camera must be in webcam mode.

Webcam mode

1. Press the Down/Flash button (10) and then the Menu button (9) until the

‘USB’ icon appears.

2. Use the Up/Playback button (6) to select the USB mode or the

Webcam mode .

3. Press the Down/Flash button (10) to conrm your choice.

4. Turn the digital camera off.

5. Connect the video camera to your computer using the USB cable pro

vided. The icon appears on the LCD screen.

6. To view the real-time images taken by the webcam, go to ‘My Computer’

and double click the new drive called ‘MegaCam’.

Downloading using ‘ArcSoft MediaImpression’

1. Connect the camera to your computer via the USB cable provided. The

camera will automatically turn on once it has been connected and

‘MSDC’ appears on the camera.

2. Launch the ‘ArcSoft MediaImpression’ program by clicking on the

shortcut . Click the ‘Import’ button on the main menu

screen.

3. In the ‘Import’ screen, click on the ‘Get Media From’ dropdown box in the

left-hand column and select the ‘Removable Disk’ driver of the camera.

Note: Make sure you have selected the ‘Removable disk’ driver or you

won’t be able to download your photos/videos.

4. Then in the ‘Destination Folder’ choose the location you want your

camera les to be stored. Click on the yellow folder to browse for a new

storage location. You can also edit the subfolder name, import option and

attach a tag.

5. Select the les you want to download. You can click on the button at the

bottom of the screen to ‘Select All’ or ‘Deselect All’, or you can hold down

the computer’s ‘Ctrl’ key and click on various les to select or deselect them.

6. Click on ‘Import’ to start downloading the les.

7. Click the ‘Done’ button to transfer the photos from your camera to the

destination folder.

Note: Click on the house image in the left-hand corner to return to the main

menu page at any time.

DJ033seriesIM1210.indb 22 25/05/2010 6:31

English

23

TROUBLESHOOTING

Q: My camera doesn’t turn on when I press the Power key. What do I do?

A:

1. Check that you have installed the batteries correctly.

2. Place new batteries in your camera.

Q: Why does nothing happen when I press the Shutter key?

A:

1. The camera’s built-in memory may be full. If this is the case, you need

to delete photos from you camera. Make sure you transfer any photos

you want to keep to your computer rst.

2. The timer may be counting down wait a few seconds.

Q: Why are my pictures unclear?

A:

1. The lens may be dirty. Gently blow any loose dust from the lens. Then

breathe gently on the lens and wipe it with a soft, clean cloth that has no

chemicals on it.

2. Make sure you hold the camera steady when taking the pictures.

3. You may be too close to your subject. Try moving further away.

Q: Why are my pictures too dark?

A:

1. The ash may be turned off. See the “Flash function” section for how to

set the ash.

2. You may need to move closer to your subject or your subject may need to

move to a lighter area.

Q: Why are my pictures too light?

A:

You may not need the ash function. See the “Flash function” section for

how to change the ash setting.

Instant messaging (chat)

You can use your camera as a webcam with your instant messaging client

(Yahoo Messenger, MSN Messenger, Skype…).

Example:

1. Put your camera in webcam mode and connect it to your computer then

launch MSN Messenger.

2. On the MSN interface, select ‘Actions’, then ‘Start a Video Conversation’.

3. Select the person you want to chat with, and press ‘OK’.

DJ033seriesIM1210.indb 23 25/05/2010 6:31

English

24

Q: Why does the camera turn off automatically?

A:

1. Your batteries may be low. Place new batteries in your camera.

2. After 30 seconds of inactivity, your camera goes into power saving mode.

Press the “Power/Mode” key and see if it turns on.

Q: I have taken photos but my computer does not recognize my cam-

era. What do I do?

A:

1. Ensure that you have in fact taken photos. Press the Shutter key a few

times to take some sample photos and then try downloading them again.

2. Always use the USB cable that came with the camera. Make sure it is

rmly connected to the camera and the computer.

3. Give your computer time to recognize the USB connection device. Try

refreshing the device options list until you see the removable device

appearing.

SPECIFICATIONS

Image Resolution 1280 x 1024 Pixels

640 x 480 Pixels

320 x 240 Pixels

Video Resolution 320 x 240 Pixels

File Format JPEG / AVI

Lens f=8.3mm, F=3.0

Exposure Auto

Self-timer 10-second delay

Interface USB 1.1

System Requirements Microsoft Windows 98SE/2000/ME/XP/Vista/7

Battery 2 x AAA

DJ033seriesIM1210.indb 24 25/05/2010 6:31

English

25

Image Resolution 1280 x 1024 Pixels

640 x 480 Pixels

320 x 240 Pixels

Video Resolution 320 x 240 Pixels

File Format JPEG / AVI

Lens f=8.3mm, F=3.0

Exposure Auto

Self-timer 10-second delay

Interface USB 1.1

System Requirements Microsoft Windows 98SE/2000/ME/XP/Vista/7

Battery 2 x AAA

MAINTENANCE

Only use a soft, slightly damp cloth to clean the unit. Do not use detergent.

Do not expose the unit to direct sunlight or any other heat source. Do not

immerse the unit in water. Do not dismantle or drop the unit. Do not try to

twist or bend the unit.

WARRANTY

This product is covered by our 1-year warranty.

For any claim under the warranty or after sale service, please contact your

distributor and present a valid proof of purchase. Our warranty covers any

manufacturing material and workmanship defect, with the exception of any

deterioration arising from the non-observance of the instruction manual or

from any careless action implemented on this item (such as dismantling,

exposition to heat and humidity, etc.). It is recommended to keep the pack-

aging for any further reference.

In a bid to keep improving our services, we could implement modication on

the colours and the details of the product shown on the packaging.

NOTE: Please keep this instruction manual, it contains important information.

Reference: DJ033series

Designed in Europe – Made in China

©Disney

United Kingdom & Ireland

For any further information, please call 0808 100 3015

http://www.lexibook.com

Environmental Protection

Unwanted electrical appliances can be recycled and should not be discarded along

with regular household waste! Please actively support the conservation of resources

and help protect the environment by returning this appliance to a collection centre (if

available).

DJ033seriesIM1210.indb 25 25/05/2010 6:31

Page is loading ...

Lexibook DJ033 User manual

Lexibook DJ033 User manual

in other languages

Related papers

Other documents