Sonoma Hardtop Gazebo 10’ X 12’
Owner’s Manual
Congratulations on your purchase of our Sonoma Hardtop Gazebo. Our clear, easy to follow,
step-by-step instructions will guide you through the assembly process from start to finish.
WARNING:
THIS UNIT IS HEAVY! For safety, DO NOT assemble this item alone. Six to eight people are
recommended for safe assembly.
Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the assembly area of the gazebo.
Do not assemble less than 6 ft / 1.8 m from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. Wear protective gloves.
When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and usage.
For outdoor use only. Install on level ground.
Check all bolts for tightness before and during usage.
IMPORTANT
Please take time to read these instructions thoroughly and follow each step carefully for safe and
easy operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. In the continental U.S., you can
call us toll-free at 1-888-301-0332 from 8 a.m. to 5 p.m. CST Monday – Friday. You can also send us
an email using the feedback icon at SamsClub.com.
Call centre for missing parts: 1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST.
Step 2
A2(x4) Top Slanting Bar B2 (x1) Big Top Frame
C2 (x4)
Middle Beam of
Big Top
D2 (x2)
Left Long Support Beam of
Big Top Long Side
E2 (x2)
Right Long Support Beam
of Big Top Long Side
F2 (x2)
Left Short Support Beam of
Big Top Long Side
G2( x2)
Right Short Support
Beam of Big Top Long
Side
H2 (x2) Left Long Support Beam of
Big Top Short Side
I2 (x2)
Right Long Support Beam
of Big Top Short Side
J2 (x2)
Left Short Support Beam of
Big Top Short Side
K2 (x2)
Right Short Support
Beam of Big Top Short
Side
Step 3
A3 (X2) Small Top Bottom Beam
1
B3 (X4) Small Top Sheeting
C3 (x2)
Roof cover of small top
long side
D3 (x2)
Roof Cover of Small Top
Short Side
E3 (x1)
Small Top Bottom
Connecting Frame
F3 (X2) Small Top Bottom Beam 2
G3 (x1) Small Top Connector H3 (x1) Small Top Cover
I3 (x1) Top Decor J3 (x1) Chandelier Hook
Step 4
A4(X4) Post Base B4 (x4) Base Cover
C4 (x4) Post D4 (x4) Top Block
E4(X4) Block Plate F4(X2) Short Right Arc Support
G4(X2) Short Left Arc Support H4(X2) Long Right Arc Support
I4(X2) Long Left Arc Support
Step 5
A5(x2)
Left Long Big Top
Cover
B5 (x2)
Right Long Big Top Cover
C5 (x4)
Left Middle Big Top
Cover
D5(x4)
Right Middle Big Top
Cover
E5 (x4)
Left Small Big Top
Cover
F5 (x4)
Right Small Big Top Cover
G5 (x2)
Short Big Top Cover
H5(X4)
Top Cover
I5(X18)
Roof Press Sheet
J5(x1)
Mosquito Netting
Hardware Pack 1
AA
Plastic Cap
16 PCS
BB
M6 Flat Washer
64 PCS
CC
M6x15 Short Bolt
64 PCS
JJ
Hook
52 PCS
LL
M6 Wrench
2PCS
Fig.1-1: Connect Decorative Gutter Connectors (F1) with Corner Decorative Gutters1 (C1) and Corner Decorative
Gutters 2 (D1) using Short Bolts (CC) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.1-2: Insert Long Decorative Gutters (A1) into Corner Decorative Gutters (C1& D1) using Short Bolts (CC)
and Flat Washers (BB). Tighten with Wrench (LL). (Note: the Corner Decorative Gutters with A1 labels)
Fig.1-3: Insert Short Decorative Gutters (B1) into Corner Decorative Gutters (C1& D1) using Short Bolts (CC)
and Flat Washers (BB). Tighten with Wrench (LL). (Note: the Corner Decorative Gutter with B1 labels)
Hardware Pack 2
Fig. 2: Attach Middle Beam Connectors (E1) to Long Decorative
Gutters (A1) and Short Decorative Gutters(B1) using Short
Bolts (CC) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.3: Attach Corner Connectors (G1) to Corner Decorative Gutter
1 (C1&D1) using Short Bolts (CC) and Flat Washers (BB).
Tighten with wrench (LL)
Fig. 4: Attach plastic cap (AA) to the one end of Long Mosquito Netting Tube (H1), then insert 7 Hooks (JJ) into
the inside rail of Long Mosquito Netting Tube (H1) as shown and 6 Hooks (JJ) into the inside rail of Short
Mosquito Netting Tubes (I1) as shown. Attach plastic cap (AA) to the other end of netting tubes. Attach the one
end of Long Mosquito Netting Tubes (H1) to Long Decorative Gutters (A1) and attach the other end one (H1) to
Corner Decorative Gutters (C1&D1) using Short Bolts (CC) and Flat Washers (BB). Repeat this step for attaching
the one end of Short Mosquito Netting Tubes (I1) to Short Decorative Gutters (B1) and attaching the other end of
Short Mosquito Netting Tubes (I1) to Corner Decorative Gutters (C1&D1). Tighten with Wrench (LL).
BB
M6 Flat Washer
64 PCS
CC
M6x15 Short Bolt
16PCS
DD
M6x15 Short Screw
32 PCS
EE
M6x55 Long Screw
16 PCS
FF
M6 Nut
16 PCS
Hardware Pack 3
Fig.5: Fix the lower end of Top Slanting Bars (A2) onto the Corner Connectors (G1) using Long Screws (EE),
Flat Washer (BB) and Nuts (FF).
Fig.6: Assemble the top end of Top Slanting Bars (A2) to Big Top Frames (B2) using Bolts (CC) and Flat
Washers (BB). Tighten with Wrench (LL).
Fig.7: Fix the lower end of Middle Beams (C2) onto the Big Top Frames (B2) using Bolts (CC) and Flat
Washers (BB).
Fig.8: Attach the lower end of Middle Beams (C2) to the lower end of Middle Beam Connectors (E1) using
Short Bolts (CC) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.9: Attach one end of Left Long Support Beams of Big Top Long Side (D2) to Middle Beams (C2) using
Short Screws (DD) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.10: Fix the other end of Left Long Support Beams of Big Top Long Side (D2) onto the Top Slanting Bars
(A2) using Short Screws (DD) and Flat Washers (BB). Repeat steps 9-10 for remaining big top beams
(E2, F2, G2, H2, J2, K2)
BB
M6 Flat Washer
20 PCS
CC
M6x15 Short Bolt
8PCS
DD
M6*15 Short Screw
8PCS
KK
M6 Nut
4PCS
Hardware Pack 4
Fig.11: Attach the top end of Small Top Bottom Beams 1 (A3) and Small Top Bottom Beams 2 (F3) to Small
Top Connectors (G3) using Nuts (KK) and Flat Washers (BB). Screw the Chandelier Hook (J3) to Small
Top Connector (G3).
Fig.12: Attach the lower end of Small Top Bottom Beams 1 (A3) and Small Top Bottom Beams 2 (F3) to Small
Top Bottom Connecting Frames (E3) using Short Bolt (CC) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.13-1: Attach assembled small top to Big Top Frames (B2) through Small Top Bottom Connecting Frames
(E3) using Short Bolts (CC) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.13-2: Place roof covers of Small Top Long Side (C3) and roof covers of Small Top Short Side (D3) to small top.
Fig.14-1: Attach Small Top Sheeting (B3) to Small Top Bottom Beams 1 (A3) and Small Top Bottom Beams 2 (F3)
using Short Screws (DD) and Flat Washers (BB). Tighten with screwdriver.
Fig.14-2: Place the Small Top Cover (H3) onto the small top and screw the Top Décor (I3) onto the exposed end
of Chandelier Hook (J3).
BB
M6 Flat Washers
92PCS
DD
M6x15 Short Screw
24 PCS
HH
Ф8*260 Peg
16PCS
II
Ф6*80 Anchor
16PCS
MM
M6x20 Long Bolt
68PCS
DD
DD
BB
BB
B3
B3
A3
A3
C3
C3
F3
F3
D3
D3
BB
BB
Fig.14-2
Fig.14-2
KK
KK
G3
G3
DD
DD
BB
BB
B3
B3
A3(F3)
A3(F3)
J3
J3
Fig.11
Fig.11
DD
DD
BB
BB
DD
DD
BB
BB
B3
B3
I3
I3
H3
H3
J3
J3
CC
CC
E3
E3
BB
BB
CC
CC
BB
BB
D3
D3
D3
D3
C3
C3
B2
B2
Fig.13-1
Fig.13-1
Fig.13-2
Fig.13-2
Fig.14-1
Fig.14-1
A3
A3
E3
E3
E3
E3
G3
G3
F3
F3
Fig.11
Fig.11
Fig.12
Fig.12
Fig.12
Fig.12
A3(F3)
A3(F3)
CC
CC
BB
BB
A3
A3
Hardware Pack 5
Fig.15: Insert the Posts (C4) into the Base Covers (B4), then install the Post Bases (A4) to the bottom of Posts
(C4) using Small Screws (DD) and Flat Washers (BB).
Fig.16: Attach the Top Blocks (D4) to the top of Posts (C4) using Long Bolts (MM) and Flat Washers (BB).
Tighten with Wrench (LL). (The screw holes on the posts and the screw holes on the block plates must
align as shown in order to secure the connection properly.)
Fig.17: Lift the assembled roof and attach the assembled post to the Corner Decorative Gutter 1 (C1) and
Corner Decorative Gutter 2 (D1) using Long Bolts (MM) & Flat Washers (BB). Tighten with Wrench (LL).
(Note: This unit is heavy. Six to eight people are recommended for this step for safe assembly.)
Fig.18: Attach the Corner Connectors (G1) to the Top Blocks (D4) using Long Bolts (MM) and Flat Washers
(BB). Tighten with Wrench (LL).
Fig. 19: Attach the Block Plates (E4) to the Top Blocks (D4) using Small Screws (DD) and Flat Washers (BB).
Tighten with Wrench (LL).
Fig.20: Attach the Short Right Arc Supports (F4) to Decorative Gutters and the Posts (C4) using Long Bolts (MM)
and Flat Washers (BB). Repeat this step for all other Arc Supports (G4 H4 I4).
Fig.21: Fix the gazebo on the grass ground with the Pegs (HH).
Fig.21: Fix the gazebo on the cement ground with the Anchors (II).
BB
M6 Flat Washer
68PCS
DD
M6x15 Short Screw
60PCS
GG
M6x40MiddleScrews
8PCS
Fig.22: Press Left Long Big Top Cover (A5) to Right Long Big Top Cover (B5)
Fig.22-1: Insert the assemblies into the U groove of Big Top Frame (B2). Repeat the steps for Short Big Top
Cover (G5).
Fig.23: Attach Left Long Big Top Covers (A5) and Short Big Top Covers (G5) to Top Slanting Bars (A2) using
Small Screws (DD) and Flat Washers (BB).
Fig.24-1: Attach Right Middle Big Top Covers (D5) and Left Middle Big Top Covers (C5) to Top Slanting Bars
(A2) using Small Screws (DD) and Flat Washers (BB). Tighten with screwdriver.
Fig.24-2: Attach Right Small Big Top Covers (F5) and Left Small Big Top Covers (E5) to Top Slanting Bars
(A2) using Small Screws (DD) and Flat Washers (BB). Tighten with screwdriver.
Fig.25: Press up the roof covers with the Roof Press Sheet (I5) and attach the Roof Press Sheet (I5) to decorative
beams using Small Screws (DD) and Flat Washers (BB). Tighten with screwdriver.
Fig.26: Insert the Top Cover (H5) into each hole of Small Top Frame (B2).
Fig.27: Attach the Top Cover (H5) on the Top Slanting Bar (A2) using Short Screws (DD) and Flat Washers (BB)
Fig.28: Hang the Mosquito Netting (J5) onto Long Mosquito Netting Tubes (H1) and Short Mosquito Netting
Tubes (I1) by Hooks (JJ). Note: Please keep mosquito netting with pre-assembled belt outside. Be
mindful of the dimensions of the item to ensure you install the Mosquito NCetting (J5) correctly.
Attach 6 hooks to Short Tubes (I1) and 7 hooks to Long Tubes (H1).
Now, your Sonoma Pavilion is ready for use.
Back up hardware pack
BB
M6 Flat Washer
15 PCS
CC
M6x15 Short Bolts
10 PCS
DD
M6x15 Short Screws
8PCS
EE
M6x55 Long Screw
1PCS
FF
M6 Nut
1PCS
GG
M6x40 Middle Screws
1PCS
JJ
Hook
8PCS
KK
M6 Nut
1PCS
IMPORTANT:
1. Keep all children and pets away from assembly area.
Children and pets should be supervised when they are in
theareaofpavilionconstruction.
2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be followed to reduce the risk
of personal injury and damage to equipment. Please read all instructions before assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the pavilion in the
ground. If you
wish to secure the pavilion to a wood deck or concrete surface, you will need to purchase fasteners appropriate for
these surfaces. These are readily available at your local hardware store or home center.
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for, or
otherwise regulate, installation and use.
9.
While this pavilion is manufactured to withstand gale force winds utilizing only the supplied ground stakes, in
areas subject to
frequent severe weather, securing the pavilion to a deck, concrete patio or footings should be
considered.
10.
Your pavilion has been engineered to accommodate winter snow loads incurred in most areas. Removal of
accumulated snow on the pavilion roof with a roof rake is recommended. In areas that are regularly subject to
blizzard conditions however, removal of the roof panel is suggested. The assembled roof structure can simply be
left intact until warmer conditions return.
CARE & Maintenance
Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it from
rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective coatings
are scratched. This is a natural process and is not a defect! To minimize this condition, we recommend care when
assembling & handling the product to prevent scratching the paint. Should any scratching or damage occur, we
recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily removed with a very light
application of common cooking oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this,
the oxidation may start dripping on to deck or patio and caused damaging stains, which may be difficult to remove.
This can be prevented if the measure is taken to keep the product from oxidizing.
Made in China
/
