Triton Systems TDM Owner's manual

TDM Firmware Loader Instructions

DC & Stepper Motor Dispensers

07103-00231-03 May 22, 2014

Corporate Headquarters:

21405 B St.

Long Beach, MS 39560

Phone: (800) 259-6672

Fax: (228) 868-9445

Copyright Notice

registered trademark of Triton Systems of Delaware LLC.

DOCUMENT UPDATES

October 15, 2013 Original

October 29, 2013 Rev B and added board/cable installation to TDM 100

December 12, 2013 Added synchronizing mainboard instructions

May 22, 2014 Added Stepper Motor installation and Rev C

TDM 200 / 250

Tools Required

T6 Driver

NO KIT REQUIRED

Description Quantity

Cassette Present Sensor w/ Security Switch 1

TDM 100 / 150 – DC Motor

Tools Required

T6 Driver

T20 Driver

TY Wrap Cutters

KIT P/N:

06200-00178

TDM 1xx Cassette Present w/Security Switch Board

Upgrade Kit

PARTS SUPPLIED

Description Quantity

Cassette Present Sensor w/ Security Switch 1

Cassette Present Cable 1

T6 | 2.5mm x 6mm | Self-Tapping | Screw 1

6 inch TY Wraps 7

TDM 100 / 150 – Stepper Motor

Tools Required

T6 Driver

TY Wrap Cutters

KIT P/N:

06200-00188

TDM 100/150 Stepper Motor Advance Security Module

Kit

PARTS SUPPLIED

Description Quantity

Security Switch Board 1

Security Switch Board Cable 1

Double-sided Tape 1

6 inch TY Wraps 3



Page1of31



InstallingtheTDMCassettePresentSensorwithSecuritySwitch

BeforestartinginstallationofTDMFirmwareLoaderv16.03RevC,theTDMCassetteSensorwith

SecuritySwitchmustbeinstalled.

AlwaysperformapropershutdownofATMbeforeservicingtheTDMmechanism.

TDM200/250

ToolsNeeded:

‐ T6Driver



Step1–Extendthedispenserslidestothefullextension(ifapplicable).Pullthereleasepindownonthe

bottomoftrayandrotatethetrayclockwise180°.Locatetheuppercassettepresentsensorboardon

thenon‐beltsideofthedispenser.NOTE:NotallATMshaveslidingorro

tatingtrays.



Step2–Unplugbothcablesfromthesensorboard.UsingaT6driver,removethescrewsecuringthe

sensorboardtothedispenser.



Page2of31



Step3–Placethecassettepresentsensorboardwithsecurityswitchinplaceonthedispenser.Secure

itwiththescrewremovedinStep2.



Step4–Plugbothcablesintothesensorboardwithsecurityswitch.

.



Page3of31



TDM100/150–DCMotor

NOTE:TDM100/150equippedwithaDCmotor,dispensersmanufacturedafter 

May2,2005(Juliandate:12205),performpages4–12.

OldermodelTDM100sequippedwithaStepperMotorskiptopage13.







DCMotor



Page4of31



ToolsNeeded:

‐ T6Driver

‐ T20Driver

‐ TYWrapCutters



Step1–Extendthedispenserslidestothefullextension(ifapplicable).Pullthereleasepindownonthe

bottomoftrayandrotatethetrayclockwise180°.Locatethecass ettepresentsensorboardmounton

thenon‐beltsideofthedispenser.NOTE:NotallATMshaveslidingorro

tatingtrays.



Step2–Installthecassettepresentsensorboardwiththescrewfromthekit.



Page5of31



Step3–Loosen,doNOTremove,thetwoscrewsontherearsidesofthemotor.

 



Step4–Removethetwoscrewsfromthefrontsidesofthemotor.Setasideforreinstallation.

 



Page6of31



Step5–Removethetwoscrewsthatsecuretheplasticshieldtothedispenser.Setasidefor

reinstallation.





Step6–Carefullytiltthemotorupandremovetheplasticshieldfromthemainboard.



Page7of31



Step7–CutandremovethetwoTYWrapsonthetopofthedispenserandthefourTYWrapsdownthe

non‐beltsideofthedispenser.

 



Step8–PlugthecableintothemainboardJ15portasshownbelow.Routethecablebehindthemain

groundwire.



Page8of31



Step9–Routethecablethroughthedispenserontopandoutonthenon‐beltside.



Step10–Plugthecableintothecassettepresentsensorboard.



Page9of31



Step11–TYWrapallthecablesintwoplacesonthetopofthedispenser.EnsuretheTYWrapwiththe

greenarrowisconnectedtotheplasticdispenserframe.CutoffexcessTYWraps.



Step12–Startingatthebottom(greenarrow),TYWrapthecablestotheplasticdispenserframein5

placesonthenon‐beltside.CutoffexcessTYWrap.



Page10of31



Step13–Carefullytiltthemotorupand tuckthewiresunderasshown.



Step14–Placetheplasticshieldinplace.Lowerthemotorbackintoplace.Ensureallwiresare

carefullytuckedundertheshieldandwillnotgetpinched.







Page11of31



Step15–Tightenthetwoscrewsholdingthemotorintoplace.



 



Step16–Securetheplasticshieldwiththetwoscrewspreviouslyremoved.







Page12of31



Step17–Reinstallthetwoscrewspreviouslyremovedonthefrontsidesofthemotor.



 



Page13of31



TDM100/150–StepperMotor

NOTE:TDM100/150equippedwithasteppermotor,dispensersmanufactured

beforeMay2,2005(Juliandate:12205),performpages13–18.



Stepper Motor



Page14of31



ToolsNeeded:

‐ T6Driver

‐ TYWrapCutters



Step1–Extendthedispenserslidestothefullextension(ifapplicable).Pullthereleasepindownonthe

bottomoftrayandrotatethetrayclockwise180°.NOTE:NotallATMshaveslidingorrotatingtrays.

Step2–Removethetwoscrewsthatsecuretheplasticshieldtoth

edispenser.Setthescrewsandthe

plasticcoverasideforreinstallation.



Step3–CutandremovetheTYWraponthetopofthedispenserandthetwoTYWrapsdownthenon‐

beltsideofthedispenser.Discard.

 



Page15of31



Step4–Peelthepaperbackingoffonesideofthedoublesidedtape.Adherethetapetothebackof

theSecuritySwitchBoard.

 



Step5–AdheretheSecuritySwitchBoardtothenon‐beltsideofthedispenserasshown.



Page16of31



Step6–Routethecablethroughthedispenserontopandoutonthenon‐beltside.



Step7–PlugtheSecuritySwitchBoardCableintoportJ1onthemainboardasshown.



Page17of31



Step8–TYWrapallthecablestothedispenserframeasshown.CutoffexcessTYWrap.



Step9–TYWrapthecabletothedispenserframeintwoplacesonthenon‐beltside.CutoffexcessTY

Wrap.



Page is loading ...

Triton Systems TDM Owner's manual

Triton Systems TDM Owner's manual

Related papers

Other documents