AXIOMTEK SBC84830 Series User manual

SBC84830 Series

Intel® Core™ Duo All-In-One

ECX Board

User’s Manual

ii

Disclaimers

This manual has been carefully checked and believed to contain

accurate information. AXIOMTEK Co., Ltd. assumes no responsibility

for any infringements of patents or any third party’s rights, and any

liability arising from such use.

AXIOMTEK does not warrant or assume any legal liability or

responsibility for the accuracy, completeness or usefulness of any

information in this document. AXIOMTEK does not make any

commitment to update the information in this manual.

AXIOMTEK reserves the right to change or revise this document

and/or product at any time without notice.

No part of this document may be reproduced, stored in a retrieval

system, or transmitted, in any form or by any means, electronic,

mechanical, photocopying, recording, or otherwise, without the prior

written permission of AXIOMTEK Co., Ltd.

CAUTION

If you replace wrong batteries, it causes the danger of explosion. It is

recommended by the manufacturer that you follow the manufacturer’s

instructions to only replace the same or equivalent type of battery,

and dispose of used ones.

May 2007, Version A1

Printed in Taiwan

iii

ESD Precautions

Computer boards have integrated circuits sensitive to static electricity.

To prevent chipsets from electrostatic discharge damage, please take

care of the following jobs with precautions:

 Do not remove boards or integrated circuits from their anti-static

packaging until you are ready to install them.

 Before holding the board or integrated circuit, touch an unpainted

portion of the system unit chassis for a few seconds. It

discharges static electricity from your body.

 Wear a wrist-grounding strap, available from most electronic

component stores, when handling boards and components.

Trademarks Acknowledgments

AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.

Windows® is a trademark of Microsoft Corporation.

Phoenix & AWARD are trademarks of Phoenix Technology Ltd.

IBM, PC/AT, PS/2, VGA are trademarks of International Business

Machines Corporation.

Intel® and Pentium® are trademarks of Intel Corporation.

Winbond is a trademark of Winbond Electronics Corp.

Other brand names and trademarks are the properties and registered

brands of their respective owners.

iv

Table of Contents

Chapter 1 Introduction................................................................... 1

1.1 Specifications ........................................................................ 2

1.2 Utilities Supports.................................................................... 4

Chapter 2 Jumpers and Connectors ............................................ 5

2.1 Board Layout and Fixing Holes..............................................5

2.2 Placement............................................................................... 7

2.3 Jumper Settings......................................................................9

2.3.1 LVDS Voltage Selection Jumper....................................9

2.3.2 Compact Flash Voltage Selection Jumper.....................9

2.3.3 CMOS Clear Jumper.................................................... 10

2.3.4 COM1, COM2 Mode Jumpers......................................10

2.3.5 Audio Output Jumper ...................................................10

2.4 Connectors..........................................................................11

2.4.1 Power Connector.......................................................... 12

2.4.2 Digital I/O Port Connector............................................12

2.4.3 LVDS Blacklight Connector.......................................... 12

2.4.4 LVDS Flat Panel Connector......................................... 13

2.4.5 Audio Connector...........................................................14

2.4.6 Power Button................................................................ 14

2.4.7 Keyboard and PS/2 Connector ....................................14

2.4.8 VGA Connector ............................................................14

2.4.9 Serial Port Interface Connectors..................................15

2.4.10 Flat Panel Bezel Connectors...................................... 16

2.4.11 Ethernet Connector.................................................... 17

2.4.12 Extension Slot ............................................................17

2.4.13 SM BUS Connector.................................................... 19

v

2.4.14 SATA Connectors.......................................................20

2.4.15 USB Connector USB2................................................20

2.4.16 USB Connector USB1................................................20

2.4.17 CPU Fan Connector................................................... 21

2.4.18 Compact Flash Connector .........................................21

Chapter 3 Hardware Description................................................. 23

3.1 Microprocessors..................................................................23

3.2 BIOS ..................................................................................23

3.3 System Memory................................................................... 23

3.4 I/O Port Address Map.......................................................... 24

3.5 Interrupt Controller...............................................................25

Chapter 4 Award BIOS Utility...................................................... 27

4.1 Entering Setup.....................................................................27

4.2 Control Keys........................................................................28

4.3 Getting Help.........................................................................28

4.4 The Main Menu....................................................................29

4.5 Standard CMOS Setup Menu..............................................30

4.6 Advanced BIOS Features....................................................32

4.7 Advanced Chipset Features................................................36

4.8 Integrated Peripherals......................................................... 38

4.9 Power Management Setup.................................................. 42

4.10 PnP/PCI Configuration Setup............................................ 45

4.11 PC Health Status...............................................................47

4.12 Frequency/Voltage Control................................................48

4.13 Load Optimized Defaults...................................................49

4.14 Set Supervisor/User Password .........................................50

4.15 Save & Exit Setup..............................................................51

4.16 Exit Without Saving........................................................... 52

Appendix A Watch Dog Timer...................................................... 53

Appendix B Digital I/O................................................................... 57

vi

SBC84830 Series All-In-One ECX Board User’s Manual

Introduction 1

C h a p t e r 1

Introduction

The SBC84830, an ECX board, supports Intel® CoreTM Duo and

CoreTM Solo processors with graphics, audio, and Gigabit Ethernet

interfaces. It is practically finest embedded Socket M board in the

market. It integrates LPC I/Os, UXGA, LCD, Ethernet and audio to

make all in one single board. Additionally, it provides you with unique

embedded features, such as onboard two RS232 serial ports and

ECX form factor that applies an extensive array of PC peripherals.

This industrial-grade board can achieve the best stability and

reliability that makes your system perform the most endurable

operation in any critical environments. The built-in Watchdog Timer

has enhanced the system reliability that achieves a unique feature to

distinguish itself from other boards.

Designed for the professional embedded developers, the Socket M

embedded board SBC84830 Series is virtually ultimate one-step

solution for embedded system applications.

SBC84830 Series All-In-One ECX Board User’s Manual

Introduction

2

1.1 Specifications

z CPU: Socket M (478) for Intel® CoreTM Duo and CoreTM Solo

processors

z System Chipset: Intel® 945GM & ICH7M

z CPU Frequency: 533/667MHz FSB

z BIOS

 Phoenix-Award BIOS, Y2K compliant

 4Mbit Flash, DMI, Plug and Play

 PXE Ethernet Boot ROM

 SmartView for multiple LCD type selection, display

mode option and application extension features

 RPL/PXE Ethernet Boot ROM

 “Load Optimized Default” to backup customized Setting in

the BIOS flash chip to prevent from CMOS battery fail

z System Memory

 One x 200-pin DDR2-400/533/667 SDRAM SODIMM

sockets

 Maximum to 2GB DDR2 memory

z L2 Cache: integrated in CPU

z Onboard IDE

 Two SATA-300 connectors

z Compact Flash Socket

 One Compact Flash Type II Socket (optional)

z Onboard Multi-I/O

 Onboard 2 x RS-232 serial ports

z USB Interface

 Four USB ports with fuse protection and complies with

USB Spec. Rev. 2.0

z Watchdog Timer

 1~255 seconds; up to 255 levels

SBC84830 Series All-In-One ECX Board User’s Manual

Introduction 3

z Graphics

 Intel® 945GM GMCH Gen 3.5 integrated graphic engine

 CRT interface for external display devices

 Maximum up to 224MB frame buffer sharing system

memory

 Maximum display resolution:

 CRT: 2048 x1536

 LVDS: 1600 X1200 (24-bit single/dual

channel LVDS interface)

 LCD backlight control supported

z Expansion Slot

 ECX expansion interface with SDVO B/C, LPC, two PCI and

one PCIe X1

z Ethernet

 One RTL8111B Gigabit Ethernet

 Wake On LAN (via ATX power supply)

 Equipped with RJ-45 interface

z Audio

 Realtek AC’97 codec audio

 MIC-in, Line-out

z Power Management

 ACPI (Advanced Configuration and Power Interface)

z Form Factor

 ECX form factor

NOTE: Specifications are subject to change without notice.

SBC84830 Series All-In-One ECX Board User’s Manual

Introduction

4

1.2 Utilities Supported

z Chipset Driver

z VGA Driver

z Ethernet Driver

z Audio Driver

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors 5

C h a p t e r 2

Jumpers and Connectors

2.1 Board Layout and Fixing Holes

Component Side

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors

6

Solder Side

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors 7

2.2 Placement

Component Side

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors

8

Solder Side

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors 9

2.3 Jumper Settings

Proper jumer settings configure the SBC84830 to meet your

application purpose. We are herewith listing a summary table of all

jumpers and default settings for onboard devices, respectively.

Here is a list of jumper settings：

Jumper Default Setting Jumper Setting

JP1 LVDS Voltage Selection

Default: 3.3V Short 1-2

JP2 Compact Flash Voltage Selection

Default: 3.3V Short 1-2

JP4 Normal Operation/Clear CMOS setting

Default: Normal Operation Short 1-2

COM2 Pin 1: DCD Short 7-9 JP5 COM2 Mode

Select COM2 Pin 8: RI Short 8-10

COM1 Pin 1: DCD Short 7-9 JP6 COM1 Mode

Select COM1 Pin 9: RI Short 8-10

JP7 Audio Speak Out/Line Out Selection

Default: Line Out Short 1-3,2-4

2.3.1 LVDS Voltage Selection Jumper: JP1

This jumper is to select the voltage for LVDS interface.

Options Settings

3.3V Short 1-2 (default)

5V Short 2-3

JP1

2.3.2 Compact Flash Voltage Selection Jumper: JP2

This jumper is to select the voltage for Compact Flash interface.

Options Settings

3.3V Short 1-2 (default)

5V Short 2-3

JP2

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors

10

2.3.3 CMOS Clear Jumper: JP4

You may need to use this jumper to clear the CMOS memory if

incorrect settings in the Setup Utility.

Options Settings

Normal Short 1-2 (default)

Clear CMOS Short 2-3

JP4

123

2.3.4 COM1, COM2 Mode Jumpers: JP5, JP6

These jumpers select the COM1, COM2 ports’ communication mode to

operate RS-232 or RS-422/485.

COM1 (COM1) JP6 COM2 (COM2) JP5

Pin 1=12V Short 1-3 Pin 1=12V Short 1-3

Pin 1=5V Short 3-5 or 5-7 Pin 1=5V Short 3-5 or 5-7

*Pin 1=DCD Short 7-9 *Pin 1=DCD Short 7-9

Pin 9=12V Short 2-4 Pin 8=12V Short 2-4

Pin 9=5V Short 4-6 or 6-8 Pin 8=5V Short 4-6 or 6-8

*Pin 9=RI Short 8-10 *Pin 8=RI Short 8-10

JP5, JP6

2.3.5 Audio Output Selection Jumper: JP7

Options Settings

Line-out Short 1-3,2-4(default)

Speak-out Short 3-5,4-6

JP7

2

4

6

1

3

5

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors 11

2.4 Connectors

Connectors connect the CPU card with other parts of the system.

Loose or improper connection might cause problems. Make sure all

connectors are properly and firmly connected. Here is a summary table

shows you all connectors on the SBC84830 Series.

Connectors Label

Power Connector CN1

Front Panel Connector (Power LED) CN2

2*5pin DIO Connector CN3

LVDS Connector CN4

LVDS Backlight Connector CN5

Audio Connector CN6

Front Panel Connector (Buzzer) CN8

HDD Activity LED Connector CN9

System Reset Switch Connector CN10

Power Button CN11

PS/2 Connector CN12

VGA Connector CN13

COM1 Connector COM1

COM2 Connector COM2

Ethernet Connector LAN1

Extension Slot J1

SMBus Connector JP3

SATA1 Connector SATA1

SATA2 Connector SATA2

USB2, USB3 Connector USB1

USB0, USB1 Connector USB2

CPU Fan Connector FAN1

CF Connector CFS1

DDRII RAM Connector DIMMS1

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors

12

2.4.1 Power Connector: CN1

Pin Signal Pin Signal

1 PS_ON 2 GND

3 GND 4 +12V

5 N.C. 6 +SB5V

7 +5V 8 +5V

9 -12V 10 GND

CN1

2.4.2 Digital I/O Port (DIO) Connector: CN3

The board is equipped a digital I/O connector CN5 that meets

requirements for a system customary automation control. The digital

I/O can be configured to control cash drawers, sense warning signals

from an Uninterrupted Power System (UPS), or perform store security

control. The digital I/O is controlled via software programming.

Pin Signal Pin Signal

1 Out-0 2 In-0

3 Out-1 4 In-1

5 Out-2 6 In-2

7 Out-3 8 GND

9 Out-4 10 GND

CN3

1

2

2.4.3 LVDS Blacklight Connector: CN5

It is a video connector for working LVDS interface backlight.

PIN Signal

1 12V

2 12V

3 5V

4 L_BLKEN

5 GND

6 GND

7 GND

CN5

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors 13

2.4.4 LVDS Flat Panel Connector: CN4

The LVDS interface which is with 40-pin connector supports

18/24-bit single/dual channel type of LCD.

Pin Signal Pin Signal

1 VCCM 2 VCCM

3 VCCM 4 VCCM

5 VCCM 6 VCCM

7 N.C. 8 N.C.

9 GND 10 GND

11 Channel B D3- 12 Channel B D0-

13 Channel B D3+ 14 Channel B D0+

15 GND 16 GND

17 Channel B CLK- 18 Channel B D1-

19 Channel B CLK+ 20 Channel B D1+

21 GND 22 GND

23 Channel A D0- 24 Channel B D2-

25 Channel A D0+ 26 Channel B D2+

27 GND 28 GND

29 Channel A D1- 30

31 Channel A D1+ 32

33 GND 34

35 Channel A D2- 36

37 Channel A D2+ 38

39 GND 40 GND

CN4

Remark: The LVDS connector on the SBC is a 40-pin connector. The

matching connector is strongly recommended to use JST

SHDR-40V-S-B.

SBC84830 Series All-In-One ECX Board User’s Manual

Jumpers and Connectors

14

The 7-pin inverter connector on the SBC is with Hirose

connector. The matching connector is strongly

recommended to use Hirose DF13-7S-1.25C.

2.4.5 Audio Connector: CN6

The board supports audio interface.CN6 is a 10pin-header connector

commonly used for the audio.

Pin Signal Pin Signal

1 MIC-IN 2 GND

3 Line In L 4 GND

5 Line In R 6 GND

7 Audio Out L 8 GND

9 Audio Out R 10 GND

CN6

1

2

2.4.6 Power Button: CN11

This 2-pin connector connects the ATX power button of the front panel

to the SBC84830 CPU card that allows users to control power on/off

state of the ATX power supply.

2.4.7 Keyboard and PS/2 Mouse Connector: CN12

CN12 is a DIN connector (AC97) for PS/2 Mouse and PS/2 keyboard

connection.

Pin Signal

1 Keyboard Data

2 Mouse Data

3 GND

4 VCC

5 Keyboard Clock

6 Mouse Clock

CN12

5

1

2

3

6

4

Keyboard Clock

GND

Keyboard Data

Mouse Data

VCC

Mouse Clock

2.4.8 VGA Connector: CN13

CN13 is a standard 15-pin pin DB15 connector commonly used for the

CRT VGA display. Please refer to the pin assignment next page.

Page is loading ...

AXIOMTEK SBC84830 Series User manual

AXIOMTEK SBC84830 Series User manual

Related papers

Other documents