KB Electronics KBAC Run-Stop-Jog Switch Kit Owner's manual

Brand: KB Electronics

Model: KBAC Run-Stop-Jog Switch Kit

Type: Owner's manual

DESCRIPTION

The Run-Stop-Jog Switch provides selection between the Main Speed Potentiometer setting or a

momentary jog speed, which can be used to index a machine into position. The switch contains three

(3) positions:

1. “Run” – The switch is placed in this position when the control output is to be set using the Main

Speed Potentiometer.

2. “Jog” – Used to provide a low speed output. This position is spring loaded so the switch must be

held. The jog speed can be changed using the JOG trimpot located on the PC board.

3. “Stop” – Used as a resting position when the Jog function is used. The motor will stop when in

this position.

MOUNTING (See Figure 1)

WARNING! Make sure that the AC line is

disconnected before installing the Run-Stop-Jog

Switch assembly.

1. KBAC Series Drives – Remove the rubber hole plug from

any available position by unscrewing the retainer nut on

the inside cover.

KBPC and KBPW Series Drives – Remove the Rubber

hole plug in the Run-Stop-Jog position by unscrewing

the retainer nut on the inside cover.

2. Install the Run-Stop-Jog Switch assembly into the front

cover making sure the key in the mounting hole lines up

with the keyway in the switch bushing. Be sure the hex

nut supplied is installed at the base of the switch bush-

ing before inserting switch into the cover. Use the nylon

spacer provided, if necessary, as shown in Figure 1. The

switch bushing threads should protrude no more than

1/4” (6.4 mm) or no less than 1/10” (2.6 mm) through

the front cover for proper installation

KBAC Series Drives: Use the Run-Stop-Jog label that is provided to cover the text around the mounting hole.

3. Install the rubber switch boot with integral hex nut over switch lever. Switch should be in the stop position to facilitate installation. Tighten the switch boot,

with the supplied hex wrench, so that the bottom seals against the Run-Stop-Jog label. Do not overtighten.

WIRING (See Figures 2A – 2D)

1. Using pliers, carefully remove the orange Main Speed Potentiometer wire from the “P2” terminal on the PC board. (Rock terminal back and forth to facilitate

removal.) Install this orange potentiometer wire onto the vacant terminal on the Run-Stop-Jog switch.

2. Install the gray wire from the Run-Stop-Jog switch onto the “P2” terminal on the PC board.

3. Install the green wire from the Run-Stop-Jog switch onto the “Jog” terminal on the PC board.

for KBAC, KBPC, and KBPW Series Drives

INSTALLATION INSTRUCTIONS

RUN-STOP-JOG SWITCH Part No. 9340B

RUBBER BOOT

FRONT COVER

SWITCH BUSHING

HEX NUT

NYLON SPACER

SWITCH BODY

$

(Back View)

Main Speed Potentiometer

Run-Stop-Jog Switch

Orange

(Back View)

White (P1)

Violet (P3)

Orange

ACCEL

Gray (P2)

Green (JOG)

Gray

P2P3

Violet

P1 JOG

MINMAX

GreenWhite

JOG Trimpot

CLBOOSTDECEL

JOG

" $ #!"!#!

Tools required: hex wrench (supplied) and pliers.

SAFETY WARNING! Please read carefully before proceeding.

This product should be installed and serviced by a qualified technician, electrician, or electrical maintenance person familiar with its operation and the hazards

involved. Proper installation, which includes electrical connections, fusing or other current protection, and grounding, can reduce the chance of electrical

shocks, and/or fires, in this product or products used with this product, such as electric motors, switches, coils, solenoids, and/or relays. Do not use this drive in

an explosion-proof application. Eye protection must be worn and insulated adjustment tools must be used when working with drive under power. This product

is constructed of materials (plastics, metals, carbon, silicon, etc.) which may be a potential hazard. Proper shielding, grounding, and filtering of this product can

reduce the emission of radio frequency interference (RFI) which may adversely affect sensitive electronic equipment. It is the responsibility of the equipment

manufacturer and individual installer to supply this Safety Warning to the ultimate end user of this product. (SW 1/2006)

Be sure to read and follow all instructions carefully. Fire and/or electrocution can result due to improper use of this product.

A COMPLETE LINE OF MOTOR DRIVES

KB ELECTRONICS, INC.

12095 NW 39th Street, Coral Springs, FL 33065-2516 • (954) 346-4900 • Fax (954) 346-3377

Outside Florida Call Toll Free (800) 221-6570 • E-mail – [email protected]

www.kbelectronics.com (A40061) – Rev. C – 9/2011

Violet

Run-Stop-Jog Switch

Orange

White (P1)

Violet (P3)

Orange

(Back View)

White

Gray (P2)

Green (JOG)

Main Speed Potentiometer

(Back View)

LED Board

CON2

Gray

JOG Trimpot

DECELMAX

JOG MIN ACCEL

Green

BOOST CL JOG

FIGURE 2B

Models KBAC-27D, KBAC-29, KBAC-29 (1P), KBAC-45 and KBAC-48

with Run-Stop-Jog Switch

LED Board MINMAXACCEL DECEL JOG

Orange

(Back View)

Run-Stop-Jog Switch

Orange

White (P1)

Green (JOG)

Gray (P2)

Switch

Start / Stop

Violet (P3)

(Back View)

Main Speed Potentiometer

STOP

White P1

Violet

Gray

Green

JOG

INH2

STOP

COM

START

CON1

INH1

JOG Trimpot

Orange

Run-Stop-Jog Switch

Orange

White (P1)

Violet (P3)

(Back View)

Green (JOG)

Gray (P2)

JOG Trimpot

CON1

STOP

Main Speed Potentiometer

(Back View)

White P1

Gray

Green

Violet P3

JOG

Start / Stop

Switch

LED Board

COM

START

JOG

FIGURE 2C

Model KBPC-240D and KBPC-225

with Run-Stop-Jog Switch

Figure 2D

Model KBPW-240D

with Run-Stop-Jog Switch

for KBAC, KBPC, and KBPW Series Drives

INSTALLATION INSTRUCTIONS

RUN-STOP-JOG SWITCH Part No. 9340B

KB Electronics KBAC Run-Stop-Jog Switch Kit Owner's manual

KB Electronics KBAC Run-Stop-Jog Switch Kit Owner's manual

KB Electronics KBAC Run-Stop-Jog Switch Kit Owner's manual

Related papers

Other documents