Intesis IN770AIR00SO000 User manual

Brand: Intesis

Model: IN770AIR00SO000

Category: Gateways/controllers

Type: User manual

Intesis IN770AIR00SO000 is an integration gateway specially designed to work as an interface between Panasonic® air conditioning units and Modbus, KNX, BACnet IP, and Home Automation systems.

The gateway allows the control and monitoring of the main AC functions, such as ON/OFF, operation mode, temperature set-point, fan speed, vane position, occupancy, etc.

The Intesis MAPS configuration software is available to help with setup.

Key features include:

Integrates Panasonic® air conditioning units into Modbus, KNX, BACnet IP, and Home Automation systems.
Allows for the control and monitoring of the main AC functions.

Intesis IN770AIR00SO000 is an integration gateway specially designed to work as an interface between Panasonic® air conditioning units and Modbus, KNX, BACnet IP, and Home Automation systems.

The gateway allows the control and monitoring of the main AC functions, such as ON/OFF, operation mode, temperature set-point, fan speed, vane position, occupancy, etc.

The Intesis MAPS configuration software is available to help with setup.

Key features include:

Integrates Panasonic® air conditioning units into Modbus, KNX, BACnet IP, and Home Automation systems.
Allows for the control and monitoring of the main AC functions.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

IN770AIR00XO000 GATEWAY CONFIGURATION GUIDE

INTESIS MAPS USER MANUAL

Version 1.0.1

Publicaon date 2023-05-14

ENGLISH

Disclaimer

The informaon in this document is for informaonal purposes only. Please inform HMS Networks of any

inaccuracies or omissions found in this document. HMS Networks disclaims any responsibility or liability for any

errors that may appear in this document.

HMS Networks reserves the right to modify its products in line with its policy of connuous product

development. The informaon in this document shall therefore not be construed as a commitment on the

part of HMS Networks and is subject to change without noce. HMS Networks makes no commitment to update

or keep current the informaon in this document.

The data, examples and illustraons found in this document are included for illustrave purposes and are only

intended to help improve understanding of the funconality and handling of the product. In view of the wide

range of possible applicaons of the product, and because of the many variables and requirements associated

with any parcular implementaon, HMS Networks cannot assume responsibility or liability for actual use

based on the data, examples or illustraons included in this document nor for any damages incurred during

installaon of the product. Those responsible for the use of the product must acquire sucient knowledge in

order to ensure that the product is used correctly in their specic applicaon and that the applicaon meets all

performance and safety requirements including any applicable laws, regulaons, codes and standards. Further,

HMS Networks will under no circumstances assume liability or responsibility for any problems that may arise as

a result from the use of undocumented features or funconal side eects found outside the documented scope

of the product. The eects caused by any direct or indirect use of such aspects of the product are undened and

may include e.g. compability issues and stability issues.

Table of Contents

1. Introducon ........................................................................................................................... 1

2. Prerequisites .......................................................................................................................... 2

3. Installaon ............................................................................................................................. 3

4. Create a New Project from a Template ........................................................................................ 4

5. Main Menu Overview .............................................................................................................. 5

5.1. Conguraon Tab ............................................................................................................. 6

5.1.1. General ................................................................................................................... 6

5.1.1.1. General Conguraon ........................................................................................ 7

5.1.1.2. Connecon ...................................................................................................... 7

5.1.1.3. Time Conguraon ............................................................................................ 7

5.1.1.4. Security ........................................................................................................... 7

5.1.1.5. Wiring Diagram ................................................................................................. 7

5.1.2. BMS Protocol ........................................................................................................... 7

5.1.3. Panasonic Protocol (Device Protocol) ............................................................................ 8

5.1.3.1. Lines Conguraon ............................................................................................ 8

5.1.3.2. Global Parameters ............................................................................................. 9

5.1.3.3. Occupancy ....................................................................................................... 9

5.1.3.4. Consumpon Funcon ...................................................................................... 10

5.2. Connecon Tab ............................................................................................................... 14

5.3. Signals Tab ..................................................................................................................... 15

5.4. Receive/Send Tab ............................................................................................................ 16

5.5. Diagnosc Tab ................................................................................................................ 16

6. BMS Protocols Available .......................................................................................................... 18

6.1. Modbus ......................................................................................................................... 18

6.1.1. Modbus Conguraon Tab ......................................................................................... 18

6.1.1.1. Modbus Conguraon ....................................................................................... 18

6.1.1.2. RTU Conguraon ............................................................................................ 18

6.1.1.3. TCP Conguraon ............................................................................................. 19

6.2. KNX .............................................................................................................................. 20

6.2.1. KNX Conguraon Tab .............................................................................................. 20

6.2.1.1. Device Conguraon ......................................................................................... 20

6.2.1.2. Operang Mode ............................................................................................... 20

6.2.1.3. Temperature Sensor .......................................................................................... 21

6.2.1.4. Fan Speed ....................................................................................................... 21

6.2.1.5. Vanes Posion ................................................................................................. 21

6.3. BACnet .......................................................................................................................... 22

6.3.1. BACnet Conguraon Tab .......................................................................................... 22

6.3.1.1. BACnet Server General Conguraon ................................................................... 22

6.3.1.2. Gateway Mode ................................................................................................ 22

6.3.1.3. BACnet Advanced Conguraon .......................................................................... 23

6.3.1.3.1. Nocaon Class ...................................................................................... 23

6.3.1.3.2. Calendars ................................................................................................ 25

6.3.1.3.3. Schedules ................................................................................................ 26

6.3.1.3.4. Trend Logs ............................................................................................... 29

6.4. Home Automaon ........................................................................................................... 31

6.4.1. Home Automaon Conguraon Tab ........................................................................... 31

6.4.1.1. Available Commands ......................................................................................... 31

6.4.1.2. TCP Conguraon ............................................................................................. 31

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1

1. Introducon

Intesis MAPS© is a soware tool for the conguraon and monitoring of the Intesis® gateways. It has been

designed and developed in-house, assuring an up-to-date tool to get all the potenal of our gateways.

Intesis MAPS is compable with Windows® 7 and higher.

The design of this conguraon tool focuses on four main pillars:

• A user-friendly interface.

•Mulple ways to create your project:

– From scratch, using a template.

–Imporng data from your computer.

– Downloading the sengs from an already congured gateway.

• Full linkage between the control system and the HVAC installaon signals.

•Real-me monitoring of the HVAC network.

Introducon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 1 of 31

2. Prerequisites

To congure the gateway, you need:

• The items supplied by HMS Networks:

Intesis IN770AIR00xO000 gateway.

Gateway documentaon.

–Installaon sheet: hp://www.intesis.com/docs/installaon-sheet-in770panxxxo000

– User manual: hps://www.intesis.com/docs/librariesprovider11/manuals-design-guides/user-manuals/ac-

interfaces/user-manual-in770panxxxo000.pdf?sfvrsn=7ce9b2d7_3

USB Mini-B type to USB A type cable.

NOTE

For Modbus TCP, KNX, BACnet IP, and Home Automaon, you can use an Ethernet cable instead

(not included).

• A computer to run the conguraon tool Intesis MAPS.

Requirements:

– Windows 7 or higher.

– Hard disk free space: 1 GB.

– RAM: 4 GB.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Prerequisites

Page 2 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

3. Installaon

Downloading the soware

1. Enter the Intesis MAPS secon on the Intesis webpage: hps://www.intesis.com/products/intesis-maps

2. Fill out the form.

NOTE

Fields marked with an asterisk (*) are mandatory.

3. Check the consent box (I hereby give consent for HMS to process my data).

4. Click the DOWNLOAD MAPS buon.

5. A .zip le will be downloaded to your computer.

Installing the soware

1. Click the .zip le to open it.

2. Double-click on the intesis-maps-installer.exe le.

NOTE

A message may pop up asking if you allow the soware to make changes to your computer. If

so, click Yes.

3. The Intesis MAPS Setup Wizard will guide you through the steps required to install Intesis MAPS on your

computer:

a. Read the license agreement and select I Agree.

b. Select the installaon folder.

4. Once the installaon is completed, click the Close buon.

Installaon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 3 of 31

4. Create a New Project from a Template

1. Open Intesis MAPS.

2. Click Create New Project in the Geng started menu on the le.

You can create a project from scratch using a template. To nd the appropriate template, lter the search

by:

• Clicking on the protocol logos.

• Typing the order code in the Order Code eld.

NOTE

The order code is printed on the silver label placed on the gateway's right side.

• Looking for it on the list.

Figure 1. The three possibilies for the template selecon

3. Select the desired template.

4. Click Next or double-click it in the list.

NOTE

The template is an example of integraon and may be used under this scope. Depending on the type

of integraon, you'll have to modify some parameters.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Create a New Project from a Template

Page 4 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

5. Main Menu Overview

Figure 2. Intesis MAPS main menu

The following secons provide an overview of the ve tabs that compose the Intesis MAPS main menu. It is

through these opons that you will congure both the gateway and your project, and monitor that everything

works ne using the Diagnosc tab.

Main Menu Overview INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 5 of 31

5.1. Conguraon Tab

Find on the le side of the Conguraon tab a menu with three opons:

•General: To set general conguraon parameters of the gateway.

•BMS Protocol: Modbus, KNX, BACnet, or Home Automaon, depending on your project's current

applicaon. In the case of the image on the le, the control installaon is based on Modbus.

•Panasonic: The protocol of the AC installaon.

5.1.1. General

Figure 3. General conguraon menu on the Conguraon tab

Use this menu to congure some general parameters of the gateway.

TIP

Toolp: Hover the cursor over a eld, and a message will appear indicang the purpose of the

parameter.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Conguraon Tab

Page 6 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

5.1.1.1. General Conguraon

•Gateway Name: Type a descripve name for your gateway.

•Project Descripon: Type a short descripon of your project.

5.1.1.2. Connecon

•IP Address: Assign an IP address for the gateway.

NOTE

When commissioning the gateway for the rst me, DHCP will be enabled for 30 seconds. During

that me, you can type an IP address of your choice. Aer that me, the default IP address

192.168.100.246 will be automacally set.

This default IP address is wrien in the installaon sheet, too.

•Net Mask: Set the gateway IP netmask.

•Default Gateway: Set the default route assigned to the gateway.

•Password: Click the Change buon and follow the instrucons to set a password for the gateway.

5.1.1.3. Time Conguraon

•Set current PC me to the gateway: Connect the gateway to your PC and click the Set buon.

•Time sync on project download: By enabling this opon, the gateway's clock sets to me when downloading

the project to the gateway.

5.1.1.4. Security

•Edit Security Conguraon: Click the Edit buon to edit the security and cercate conguraon.

5.1.1.5. Wiring Diagram

•Check Gateway's Wiring Diagram: Click the View buon to open a schemac image on how to wire the

gateway.

5.1.2. BMS Protocol

The parameters in this menu vary depending on the current applicaon. Consult these secons for each protocol:

•Modbus (page 18)

•KNX (page 20)

•BACnet (page 22)

•Home Automaon (page 31)

Conguraon Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 7 of 31

5.1.3. Panasonic Protocol (Device Protocol)

Figure 4. Panasonic protocol parameters inside the Conguraon tab

Use this menu to integrate AC indoor and outdoor units into your project and congure some Panasonic protocol

parameters.

5.1.3.1. Lines Conguraon

1. Select the Panasonic Line.

2. Select the Gateway Address in Panasonic line: Address 1 or Address 2.

•Autodiscover Panasonic Line: This funcon discovers all indoor and outdoor units connected to the

installaon.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Conguraon Tab

Page 8 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

1. Click the Scan buon to open the Scan Panasonic Units window:

Figure 5. Bus Scan window

2. Click the Installaon with units not addressed (no central address assigned) checkbox if applicable.

If so, set the OU Scan range by selecng its low and high limits.

3. Start the bus scanning by clicking the Scan buon.

4. Once the scanning has nished, you can select or deselect which units you want to integrate.

– Check the Replace Units opon if you want the units you have now selected to replace the previously

listed units.

– Check the Add Units opon if you want to add the units you have now selected to the previously listed

units.

5. Click Apply to replace/add the discovered units you have selected.

•Units Conguraon: Use this table to congure some parameters related to the AC units of your project:

–Unit ID: Check which units you want to integrate.

–OU: Set a number for each outdoor unit.

–IU: Set a number for each indoor unit.

–Descripon: Type a descripon for each unit.

5.1.3.2. Global Parameters

• Panasonic Temperature Units: Temperature unit in Celsius or Fahrenheit degrees.

5.1.3.3. Occupancy

•Enable Occupancy Conguraon: Click the checkbox to enable this parameter.

•Occupancy Cool Setpoint (OCS): Set the temperature for the cool mode when the room is occupied (Celsius: 1

to 100ºC, Fahrenheit: 33 to 212ºF).

•Unoccupancy Cool Setpoint (UCS): Set the temperature for the cool mode when the room is unoccupied

(Celsius: 1 to 100ºC, Fahrenheit: 33 to 212ºF).

Conguraon Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 9 of 31

IMPORTANT

UCS must always be greater or equal to OCS.

•Occupancy Heat Setpoint (OHS): Set the temperature for the heat mode when the room is occupied (Celsius:

1 to 100ºC, Fahrenheit: 33 to 212ºF).

•Unoccupancy Heat Setpoint (UHS): Set the temperature for the heat mode when the room is unoccupied

(Celsius: 1 to 100ºC, Fahrenheit: 33 to 212ºF).

IMPORTANT

UHS must always be smaller or equal to OHS.

IMPORTANT

The minimum dierence between Cool and Heat setpoints must be 2ºC / 4ºF.

•Connuous Check: Click the checkbox to enable/disable this parameter. When enabled, the gateway checks

the occupancy when there's any change in the room's temperature. If the parameter is unchecked, it only

checks the occupancy when the occupancy status changes.

•Standby for Unoccupancy: Click the checkbox to enable/disable this parameter, which determines the indoor

unit's behavior while the ambient temperature is in between the deadband. If enabled, the indoor unit will

turn o; if disabled will remain on.

•Force on startup: Click the checkbox to enable/disable this parameter. If enabled, the values you set in the

conguraon screen will be loaded aer a reset. If disabled, the last values selected will be loaded aer reset.

5.1.3.4. Consumpon Funcon

With this funcon, you can monitor the energy consumpon of the integrated indoor units.

IMPORTANT

Before using this funcon, ensure the AC system and the pulse/Modbus energy meters are already

installed, wired, congured, and properly working.

•Enable Consumpon Funcon: Click the checkbox to enable this parameter.

•Select Energy Meters Input Mode: Choose between Modbus TCP Energy Meters and Pulse Meters & Binary

Inputs.

•Energy Meters Conguraon: Click the Edit buon to open the Energy Meter Conguraon window.

NOTE

The conguraon parameters will vary depending on the energy meter type selected.

– Energy meter conguraon for Modbus TCP Energy Meters.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Conguraon Tab

Page 10 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

Use the Select Meter parameter to choose the energy meter you want to congure.

NOTE

Up to three energy meters are available.

•Meter 1 Conguraon.

–Descripon: Type a descripon for the meter.

–IP Address: It shows the IP address where the meter is located.

–Port: Port for the Modbus TCP/IP connecon. (502 port by default).

–Slave Number: Energy meter slave Modbus address (1 to 254).

–Modbus Register (acve energy imported): Modbus register to read (1 to 65535).

–Register Units: Choose Wh or kWh.

–Read Funcon: Read register type for this funcon. Choose between funcon 3: Read Holding

Registers and funcon 4: Read Input Registers.

–Data Length: Number of bits for the Modbus register (16, 32, or 64 bits).

–Format: Select the data type between 0: Unsigned, 1: Signed (C2), 2: Signed (C1), 3: Float.

–Byte Order: Choose Big Endian, Lile Endian, Word Inv BE, Word Inv LE.

•Advanced MB Conguraon.

You can modify these Modbus parameters to adapt the Modbus communicaon to every installaon.

IMPORTANT

These parameters are for advanced users only. As a general rule, keep the default values for

proper communicaon with the meter.

–Time InterFrame: Select the minimum me between received and sent frames (0 to 100000 ms.

Default value: 10 ms).

–Retry Timeout: Select the minimum me between retry frames aer no response on the TCP

connecon (0 to 30000 ms. Default value: 5000 ms).

–Conn. Timeout: Select the minimum me before launching an error message aer no response on the

TCP connecon (100 to 30000 ms. Default value: 10000 ms).

Conguraon Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 11 of 31

–RX Timeout: Select the minimum me before launching an error message when no TCP frames are

received but the TCP connecon is OK (100 to 30000 ms. Default value: 5000 ms).

–Time Slave Chg: Select the minimum me of silence when changing from one slave device to another

one (100 to 10000 ms. Default value: 100 ms).

– Energy meter conguraon for Pulse Meters & Binary Inputs.

Use the Select Meter parameter to choose the energy meter you want to congure.

•Meter 1 Conguraon.

–Descripon: Type a descripon for the meter.

–Binary Input (not editable): It shows to which gateway's digital input the meter will connect.

–Pulse Measurement: Set the equivalence between pulses and energy.

IMPORTANT

This value must match with the conguraon of the energy meter device.

–Pulse Width: It denes the width of each pulse.

IMPORTANT

This value must match with the conguraon of the energy meter device.

–Trigger Edge Mode: Choose between Falling or Raising mode.

–AC Consumpon Refresh Time: It denes the me to refresh the consumpon values for this energy

meter.

•Energy Metering Signals Mode. Choose between:

–General Consumpon. It acvates three signals for each indoor unit:

•Consumpon Yesterday

•Consumpon Today

•Consumpon Total

–Cool/Heat modes consumpon. It acvates six signals for each indoor unit:

•Consumpon Yesterday Heat

•Consumpon Today Heat

•Consumpon Total Heat

•Consumpon Yesterday Cool

•Consumpon Today Cool

•Consumpon Total Cool

•Energy Metering Units: Choose between Wh or KWh.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Conguraon Tab

Page 12 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

•Assignaon table. Use this table to assign the previously selected Indoor Units to each Energy Meter.

• Select the Energy Meter for each Outdoor Unit/Indoor Unit.

Conguraon Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 13 of 31

5.2. Connecon Tab

Figure 6. Connecon tab window

1. On the Connecon Type parameter, select the way you connected the gateway to your PC:

• Select IP if you are using the Ethernet port of the Intesis gateway.

IMPORTANT

Make sure you have an internet connecon.

NOTE

When using the IP connecon, the gateway's name appears:

–In black: It is compable with the selected template.

–In red: It is not compable with the selected template.

• Select USB Port if you are using the Console port of the gateway.

2. Select your gateway from the Discovered Gateways list on the le.

3. Click Connect.

NOTE

If your Intesis gateway rmware doesn't match the selected template, a pop-up window will prompt

you to download the correct rmware.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Connecon Tab

Page 14 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

5.3. Signals Tab

This menu lists all available signals and their parameters for both BMS and Device protocols.

Figure 7. Signals tab for the Modbus server applicaon

Regardless of the protocol, all signals share some common characteriscs and parameters:

Signals background color meaning:

•Blue: General system signals.

•Orange: Signals for the outdoor units.

•White: Signals for the indoor units.

Below the list of signals, these opons are available:

•Acve signals: Number of acve signals in the list.

•Hide Disabled signals: Check this opon to hide all disabled signals from the list.

•Edit Columns: Click this buon to hide/show any column of the list.

•Export: Click this buon to export the current signals' conguraon to an xls le.

Signals Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 15 of 31

•AA: Increases or decreases the font size.

•Check table: Click this buon to check the signals' conguraon. If any parameter on any signal is wrong, a

message will pop up with specic informaon about the error.

5.4. Receive/Send Tab

Send:

Once you have nished seng the parameters, you have to send the conguraon to the gateway.

Follow these steps:

1. Click the Send buon.

a. If the gateway is sll factory-set, you will be prompted to save the project on your PC. Once you save it,

the conguraon is automacally sent to the gateway.

b. If you have already saved the project, the conguraon is automacally sent to the gateway.

2. Connect again with the gateway aer sending the le.

NOTICE

The gateway will reboot automacally once the new conguraon is loaded. This process may

take a few seconds.

Receive:

Use this funcon to get the conguraon of a gateway, for example, when you need to change some parameters

of a gateway already mounted in an installaon.

Once the conguraon is completed and sent, the gateway is already operave. Even so, you should check that

everything is working correctly by entering the Diagnosc tab.

5.5. Diagnosc Tab

IMPORTANT

Connecon with the gateway is required to use the diagnosc tools.

ToolBox:

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Receive/Send Tab

Page 16 of 31 INTESIS MAPS USER MANUAL Version 1.0.1

Use the tools secon to:

•Microprocessor icon: Check the current hardware status of the gateway.

•LOG: Set Intesis MAPS in logging mode to record all the informaon present in the viewers and save it in a .zip

le.

•INFO?: Get some gateway informaon.

•RESET: Reset the gateway.

NOTE

Depending on your screen resoluon, the ToolBox icons may appear parally hidden behind the

Viewers window.

Viewers:

Intesis MAPS provides several viewers:

• A generic console viewer for general informaon about communicaons and the gateway status.

• A viewer for both protocols to check their current status.

• A signals viewers to simulate the BMS behavior or check the system's current values.

Diagnosc Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.1 Page 17 of 31

Page is loading ...

Intesis IN770AIR00SO000 User manual

Brand: Intesis

Model: IN770AIR00SO000

Category: Gateways/controllers

Type: User manual

Intesis IN770AIR00SO000 is an integration gateway specially designed to work as an interface between Panasonic® air conditioning units and Modbus, KNX, BACnet IP, and Home Automation systems.

The gateway allows the control and monitoring of the main AC functions, such as ON/OFF, operation mode, temperature set-point, fan speed, vane position, occupancy, etc.

The Intesis MAPS configuration software is available to help with setup.

Key features include:

Integrates Panasonic® air conditioning units into Modbus, KNX, BACnet IP, and Home Automation systems.
Allows for the control and monitoring of the main AC functions.

Download PDF

report

Intesis IN770AIR00SO000 User manual

Intesis IN770AIR00SO000 User manual

Related papers

Other documents