aFe Power 49-48062-P Installation guide

Brand
aFe Power
Model
49-48062-P
Type
Installation guide

This manual is also suitable for

aFe Power 49-48062-P is a 2-1/2" Stainless Steel Axle-Back Exhaust System designed for Jeep Wrangler JK models from 2007 to 2018 with V8-3.6L/3.8L engines. This exhaust system features polished tips and is engineered to improve exhaust flow and sound while maintaining a deep, aggressive tone. The system includes all necessary hardware for a hassle-free installation and is backed by aFe's limited lifetime warranty.

aFe Power 49-48062-P is a 2-1/2" Stainless Steel Axle-Back Exhaust System designed for Jeep Wrangler JK models from 2007 to 2018 with V8-3.6L/3.8L engines. This exhaust system features polished tips and is engineered to improve exhaust flow and sound while maintaining a deep, aggressive tone. The system includes all necessary hardware for a hassle-free installation and is backed by aFe's limited lifetime warranty.

INSTALLATION INSTRUCTIONS
MAKE: Jeep
MODEL: Wrangler (JK)
YEAR: 2007-2018
ENGINE: V8-3.6L/3.8L (2DR/4DR)
Step 1. (Read Instructions prior to installation). It may be helpful to lubricate all the factory isolation rubber mounts, before
taking off stock exhaust and also before installing aFe exhaust. Always use a Jack or Stand to support muffler when
installing or uninstalling any exhaust system.
Step 2. Remove your stock axle back exhaust from the rear. Take caution not to damage the factory isolation mounts as they
will be reused.
Step 3. Install the aFe axle back exhaust.
Step 4. Place a 2.5" band clamp over the rear aFe axle back muffler assembly. The slide the over axle pipe into rear aFe axle
back muffler assembly slip hangers into rubber isolation mounts.
Step 5. Install tips. Align system and begin to tighten down clamp.
Step 6. Recheck all work done for tightens. Remove vehicle from jack stands.
Step 7. Congratulations your exhaust is now complete and ready for daily use! It is recommended to re-tighten all clamps after
50-100 miles. Note: It is normal for the aFe Power Cat-back exhaust to emit smoke for the first few minutes upon
initial start-up.
NOTES:
• aFe recommends that the tailpipe be at least 1/2”-1” away from any body panels to avoid heat related body damage. Tighten and secure.
06-86365
Updated: December, 2017
Caution: Allow time for your vehicle to cool down prior to installation. When working on or under your vehicle proceed with caution. Exhaust systems reach high
temperatures and may cause serious burns. Wear protective safety equipment; eye goggles and gloves to ensure a safe installation. aFe recommends professional
installation on our products.
2-1/2" Stainless Steel
Axle-Back Exhaust
49-48061-B (Black Tips)
49-48061-P (Polished Tips)
Muffler Assembly
05-144359B
(Black)
Exhaust Tip
49T30451-B091 (Black)
Exhaust Tip
49T30452-B091 (Black)
Muffler Assembly
05-144359P
(Polished)
Clamp, Band 2-1/2"
05-41061
Exhaust Tip
49T30451-P09 (Polished)
Exhaust Tip
49T30452-P09 (Polished)
Clamp, Band 2-1/2"
05-41061
Clamp, Band 3"
05-41055
Clamp, Band 3"
05-41055
Clamp, Band 3"
05-41055
Clamp, Band 3"
05-41055
  • Page 1 1

aFe Power 49-48062-P Installation guide

Brand
aFe Power
Model
49-48062-P
Type
Installation guide
This manual is also suitable for

aFe Power 49-48062-P is a 2-1/2" Stainless Steel Axle-Back Exhaust System designed for Jeep Wrangler JK models from 2007 to 2018 with V8-3.6L/3.8L engines. This exhaust system features polished tips and is engineered to improve exhaust flow and sound while maintaining a deep, aggressive tone. The system includes all necessary hardware for a hassle-free installation and is backed by aFe's limited lifetime warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents