Aplex PhanTAM-816BP/H User manual

PHANTAM-8XXB Series

15.6”, 18.5” and 21.5” IP66/IP69K

Intel Elkhart Lake

Fanless Stainless Steel Panel PC

User Manual

Release Date Revision

Nov.2023 V1.0

Aplex Technology, Inc.

15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan

Tel: 886-2-82262881 Fax: 886-2-82262883 Email: [email protected] URL: http://www.aplex.com

PHANTAM-8XXB Series User Manual

1

Revision History

Reversion

Date

Description

1.0

2023/11/28

Initiation

PHANTAM-8XXB Series User Manual

2

Warning!_______________________________________

Caution

Risk of explosion if the battery is replaced with an incorrect type.

Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local

environmental regulations.

Disclaimer

This information in this document is subject to change without notice. In no event shall Aplex Technology

Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or

misuse of information in this document or in any related materials.

This equipment generates uses and can radiate radio frequency energy and if not installed and

used in accordance with the instructions manual, it may cause interference to radio communications.

It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC

Rules, which are designed to provide reasonable protection against such interference when operated

in a commercial environment. Operation of this equipment in a residential area is likely to cause

interference in which case the user at his own expense will be required to take whatever measures

may be required to correct the interference.

Electric Shock Hazard – Do not operate the machine with its back cover removed. There are dangerous

high voltages inside.

PHANTAM-8XXB Series User Manual

3

Safety Precautions

Follow the messages below to prevent your systems from damage:

◆ Avoid your system from static electricity on all occasions.

◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on.

Always disconnect power when the system is not in use.

◆ Disconnect power when you change any hardware devices. For instance, when you connect a

jumper or install any cards, a surge of power may damage the electronic components or the

whole system.

PHANTAM-8XXB Series User Manual 

Table of Contents 
 
Revision History ................................................................................................................................. 1 
Warning!_______________________________________ ...................................................................... 2 
Safety Precautions ............................................................................................................................. 3 
Chapter 1 System Product ........................................................................................................ 6 
1  Features ................................................................................................................................. 6 
2  Specifications .......................................................................................................................... 6 
3 Display .................................................................................................................................. 8 
4  Dimensions ............................................................................................................................. 9 
5  Brief Description of PHANTAM-8XXB Series .............................................................................. 11 
6  VESA Mount and SWING ARM ................................................................................................. 14 
Chapter 2 Hardware ................................................................................................................. 15 
1 Specifications ...................................................................................................................... 15 
2 Board Dimensions ............................................................................................................... 17 
3 Jumpers and Connectors Location .................................................................................... 189 
4 Jumpers Setting and Connectors ........................................................................................ 19 
 
Chapter 3 BIOS Setup Description ......................................................................................... 29 
1 Operations after POST Screen ........................................................................................... 29 
2 BIOS SETUP UTILITY ........................................................................................................ 29 
3 Main Settings ...................................................................................................................... 30 
4 Advanced Settings .............................................................................................................. 31 
5 Chipset Settings .................................................................................................................. 48 
6 Security Settings ................................................................................................................. 85 
7 Boot Settings ....................................................................................................................... 86 
8 Save & Exit Settings ............................................................................................................ 87 
Chapter 4 Installation of Drivers ............................................................................................. 89 
1 Intel Chipset ........................................................................................................................ 90 
2 Intel®  HD Graphics Chipset ................................................................................................ 92 
3 Realtek HD Audio Driver Installation ................................................................................... 94 
4  LAN Driver............................................................................................................................. 95 
5  Intel® Management Engine Interface ....................................................................................... 96 
6  Touch Screen Installation ........................................................................................................ 98 
 
 
 
 

PHANTAM-8XXB Series User Manual

5

Figures

Figure 1: Dimensions of PHANTAM-816BP/BR(H)………………………..………………..…….…………..…9

Figure 2: Dimensions of PHANTAM-821BP/BR(H)………..……………………………………………………10

Figure 3: Front View of PHANTAM-816BP/BR(H)………….……….……………………..……………………12

Figure 4: Rear View of PHANTAM-816BP/BR(H)…………..……….……..……………………………………12

Figure 5: Front View of PHANTAM-821BP/BR(H)……….….……….……………………….…………………13

Figure 6: Rear View of PHANTAM-821BP/BR(H)….…..………….……………………………………………13

Figure 7: PHANTAM-8XXB VESA Mount………………..……..…...………………………………………………14

Figure 8: PHANTAM-8XXB SWING ARM………………..….....……………………………………………………14

PHANTAM-8XXB Series User Manual

6

Chapter 1 System Product

1.1 Features

⚫ 15.6”/18.5”/21.5” Stainless Steel Panel PC

⚫ Intel® Atom® Elkhart Lake x6000 series, and Intel® Pentium® and Celeron® N and J series Processor

⚫ IP66/69K Full-sealed with Anti-Corrosion Enclosure

⚫ Gap-free sealing and Slim Front Frame architecture at front bezel

⚫ Special Hygienic Screws on I/O cover

⚫ Optional Robust Waterproof Wireless Antenna Cover and Air Pressure Balance Screw

⚫ M12 Connectors with Waterproof cover and chain

⚫ DC 9~36V wide-ranging power input

⚫ Support VESA Mount or Swing ARM

1.2 Specifications

PHANTAM-8XXB

System

CPU

Intel®Celeron®J6412 (1.8GHz/2.60GHz, 1.5MB L2 cache, 10W TDP) (default)

Chipset

Integrated with SoC

Memory

Up to 32GB DDR4-3200 SDRAM (one SO-DIMM slot)

LVDS

1 x 24 bit Dual Channel onboard LVDS interface, up to 1920 x 1200@ 60Hz

IO Port

USB

1 x M12 8pin for 2 x USB2.0 (TB-536-U2) with waterproof cap and chain

Serial/Parallel

1 x M12 8pin for COM1, RS-232/422/485 (Default RS-232) with waterproof cap and chain

LAN

1 x M12 8pin for LAN with waterproof cap and chain

Power

1 x Power Switch at rear side

Option

NFC module design at front side

2 x M12 Blank for option with waterproof cover and chain(Either two, priority: COM, USB, LAN)

⚫ 2 x USB2.0 ‧1 x USB3.2 Gen1 (Down Drew I/O only)

⚫ 1 x GbE LAN ‧1 x COM

Storage Space

Storage

1 x M.2 B Key (SATA III), default support 2242(2280 for option, and can’t use TB-528 series at the

same time)

Expansion

Expansion Slot

⚫ 1 x Full-size mini-PCIe slot for 4G/5G (PCIe3.0x1, USB2.0, SMBus)

⚫ 1 x M.2 2230 E-Key socket for optional Wi-Fi/BT Module (PCIex3.0 x 1+USB2.0)

⚫ 1 x Micro SIM slot

Touch Screen – Resistive Touch Window Type

TS Control

PenMount 6000 on Board

PHANTAM-8XXB Series User Manual

7

Interface

USB

Light Transmission

Over 80%

Touch Screen – Projected Capacitive Type

TS Control

Chip on tail

Interface

USB

Light Transmission

90%

Antenna

Option Wi-Fi/BT module and 2 x External antenna at rear side

RFID

RFID module design on the front side by supporting Android and Linux driver or BSP

module and porting by customer side or use Aplex-recommended module.

Power

Power Input

DC 9~36V (onboard)

1 x M12-3pin for DC power with waterproof cover and chain

1 x Power Switch at rear side

Mechanical

Construction

304 Stainless Steel chassis (default)

316 Stainless Steel chassis (option)

Mounting

VESA 100 x 100mm

Swing ARM for option

IP Rating

Total IP66/IP69K

Operating System Support

OS Support

Windows 10 IoT Enterprise

Windows 11 IoT SAC/PRO

Environmental

Operating

Temperature

0~50°C(-20℃ to 60℃ optional)

Storage Temperature

-30~70°C

Humidity

10 to 90% @ 40°C, non-condensing

Certification

CE / FCC Class A

PHANTAM-8XXB Series User Manual

8

1.3 Display

Standard LCD

PHANTAM-816BP/R

PHANTAM-821BP/R

Display Type

15.6” TFT LCD

21.5” TFT LCD

Max. Resolution

1366 x 768

1920 x 1080

Max. Color

16.7M/16.7M

16.7M

Luminance(cd/m²)

400 nits

450 nits

250 nits

Contrast Ratio

500:1/800:1

1000:1

Viewing angle(H/V)

170 / 170

178/178

Backlight Lifetime

(Hrs)

50,000

Power Consumption

MAX:39.73W

MAX:32.48W

Mounting(mm)

VESA 100 x 100

Swing ARM (option)

Dimensions(mm)

404.4x255.4x64.5

540.4x332.4x61.9

Net Weight(Kg)

4.45

7.88

High Brightness LCD

PHANTAM-816BP/RH

PHANTAM-821BP/RH

Display Type

15.6” TFT LCD

21.5” TFT LCD

Max. Resolution

1366 x 768

1920 x 1080

Max. Color

16.7M/16.7M

16.7M

Luminance(cd/m²)

1000 nits

Contrast Ratio

500:1/1000:1

1000:1

Viewing angle(H/V)

160 / 160

170 / 170

178/178

Backlight Lifetime

(Hrs)

50,000

Power Consumption

MAX:39.73W

MAX:32.48W

Mounting

VESA 100 x 100

Swing ARM (option)

Dimensions(mm)

403.4x254.4x64.9

540.4x332.4x61.9

Net Weight(Kg)

4.45

7.88

PHANTAM-8XXB Series User Manual

9

1.4 Dimensions

Figure 1 Dimensions of PHANTAM-816BP/BR(H)

PHANTAM-8XXB Series User Manual

10

Figure 2 Dimensions of PHANTAM-821BP/BR(H)

PHANTAM-8XXB Series User Manual

11

1.5 Brief Description of PHANTAM-8XXB Series

There are 15.6” and 21.5” Stainless Steel Panel PC in PHANTAM-8XXB series, which comes with flat

front panel design and Stainless Steel 304 Enclosure. It is powered by Intel® Atom® Elkhart Lake x6000 series,

and Intel® Pentium® and Celeron® N and J series Processor, with one SO-DIMM DDR4 slot, up to 32GB 3200

MHz. These systems support DC 9~36V wide-ranging power input and IP66/IP69K front panel with M12

connectors. Projected capacitive touch support 7H anti-scratch surface is ideal for use as PC-based controller

for Industrial Automation & Factory Automation. Furthermore, PHANTAM-8xxB Series are capable of

expanding the function by option expansion, includes Mini-PCIe, CAN bus, POE, USB, and isolation I/O

module to improve competitive advantage through providing critical flexibility and expansibility for the

variety of application and requirement.

PHANTAM-8XXB Series User Manual

12

Figure 3 Front View of PHANTAM-816BP/BR(H)

Figure 4 Rear View of PHANTAM-816BP/BR(H)

PHANTAM-8XXB Series User Manual

13

Figure 5 Front View of PHANTAM-821BP/BR(H)

Figure 6 Rear View of PHANTAM-821BP/BR(H)

PHANTAM-8XXB Series User Manual

14

1.6 VESA Mount and SWING ARM

The PHANTAM-8xxB series is designed to be VESA mount and SWING ARM as shown in pictures below.

Figure 7 PHANTAM-8XXB VESA MOUNT

Figure 8 PHANTAM-8XXB SWING ARM

PHANTAM-8XXB Series User Manual

15

Chapter 2 Hardware

SBC-7127 is a 3.5” industrial motherboard developed on the basis of Intel Elkhart Lake, which provides

abundant peripheral interfaces to meet the needs of different customers. Also, it features two GbE

ports, 4-COM ports and one Mini PCIE and one M.2 2230 configuration. To satisfy the special needs of

high-end customers, due to its compact size, the product is widely used in various sectors of industrial

control.

2.1 Specifications

Specifications

Board Size

146mm x 101.6mm

CPU Support

Intel Celeron J6412 Processor,2.0GHz up to 2.60GHz,10W

Intel Atom x6425E Processor,2.0GHz up to 3.00GHz,12W (option)

Chipset

SoC

Memory Support

1x SO-DIMM (260pins), up to 32GB DDR4 3200MT/s

Graphics

Integrated Intel UHD Graphics 400/800 MHz (J6412)

Integrated Intel UHD Graphics 500/750 MHz (x6425E)

Display Mode

1 x DisplayPort1.4, DP++ via DP Port

1 x HDMI1.4b via HDMI Port

1 x LVDS (18/24-bit dual LVDS)

Support

Resolution

DP: support up to 4096 x 2160 @60Hz

HDMI: support up to 3840x2160@30Hz

LVDS: support up to 1920 x 1200

Super I/O

ITE IT8786E-I/HX

BIOS

AMI/UEFI BIOS

Storage

1 x SATAIII via 7pin SATA connector

1 x M.2 B-Key(SATA III/PCIe auto detect),2242/2280 for Storage

Ethernet

1 x 10/100/GbE LAN via intel® I210-AT controller (PXE/WoL)

1 x 10/100/1000/2.5GbE LAN via intel® I225-LM/I226-LM controller

(PXE/WoL)

USB

2 x USB3.2 gen2/USB2.0,Type-A stack ports (USB3_1)

2 x USB2.0 via pitch 2.0mm 2x5pin header (USB1)

2 x USB2.0 via pitch 2.0mm 2x5pin header (USB2)

1 x USB2.0 for touch screen (CN3)

1x USB2.0 for MPCIE1

1x USB2.0 for M2_E1

PHANTAM-8XXB Series User Manual

16

Serial

1 x RS-232(default)/422/485, signals select via BIOS (COM1), pin9

RI(default)/5V/12V, select via JP1. (DB9, COM1)

1 x RS-232 via pitch 2.0mm 2x5pin header, pin9 RI(default)/5V/12V,

select via JP2 (COM2)

2 x 2wired RS485 via pitch 2.0mm 2x5pin header (COM3)

GPIO

8-bit digital I/O by Pin header (GPIO2)

4-bit digital Input

4-bit digital Output

Audio

Support Audio via Realtek ALC888S-VD2 HD audio codec

1x Line out via 3.5mm audio jack

Support Line-in,Line-out,MIC by 2x6-pin header

Expansion Slots

1 x full-sized mini-PCI-express slot (MPCIE1) with micro SIM slot

(SIM1)

1 x M.2 E-Key(PCIex1,USB2.0),2230 for WIFI/BT module

FAN

1x 4pin fan connector

Watchdog Timer

Software programmable 1–255 level

TPM

-Onboard TPM IC Infineon_SLB9670AQ2.0

-Support fTPM, select via BIOS

Switches and

LED Indicators

Power button/reset button/power LED/HDD LED/buzzer via pitch

2.0mm 2x5pin header (FP1)

Battery

Support 3V RTC Li-battery via 2pin wafer (BAT1)

Power

Management

Wide range DC 9~36V±10% power input via 2pin terminal block

Temperature

Operating: -20℃ to 70℃

Storage: -40℃ to 85℃

Humidity

10% - 90%, non-condensing, operating

Certifications

Meet

CE/FCC class A

UL

RoHS2.0

PHANTAM-8XXB Series User Manual

17

2.2 Board Dimensions

(units :mm)

Figure 2.1: Board Dimension of SBC-7127

PHANTAM-8XXB Series User Manual

18

2.3 Jumpers and Connectors Location

Board Top

Board Bottom

PHANTAM-8XXB Series User Manual

19

2.4 Jumpers Setting and Connectors

1. CPU1:

(FCBGA1493) Onboard Intel Elkhart Lake SoC.

Model

SoC

Numbe

r

PBF

Cores/

Threads

TDP

Remarks

SBC-7127-J6412

J6412

2.0~2.6GHz

4 / 4

10W

Default

SBC-7127-X6425E

X6425E

2.0~3.0GHz

4 / 4

12W

Option

2. DDR4_1:

(SO-DIMM 260Pin slot) DDR4 memory socket, the socket is located at the top of the board and supports

260Pin 1.2V DDR4 SO-DIMM memory module up to 32GB.

Max Memory Size (dependent on memory type).

3. BAT1:

(1.25mm Pitch 1x2 wafer Pin Header) 3.0V Li battery is embedded to provide power for CMOS.

Pin#

Signal Name

Pin1

VCC_RTC

Pin2

GND

4. SW1:

(2.00mm Pitch 2x6 Pin Header) Power mode and LVDS setting.

Switch

Open

Close

Pin1-2

Default, PWRBTN-ON

Auto-PSON

Pin3-4

ATX Mode

Default, AT Mode

Pin5-6

Default, Normal

Close 1sec to Clear CMOS

Pin7-8

Default, Normal

Write EDID

Pin9-10

Default, LVDS Dual CH.

LVDS Single CH.

Pin11-12

Default, LVDS 6 bit Signal

LVDS 8 bit Signal

Page is loading ...

Aplex PhanTAM-816BP/H User manual

This manual is also suitable for

Aplex PhanTAM-816BP/H User manual

Related papers

Other documents