RAB Lighting JBKNOOKFA Operating instructions

RAB Lighting
Brand
RAB Lighting
Model
JBKNOOKFA
Category
Decorative lighting
Type
Operating instructions

This manual is also suitable for

RAB Lighting JBKNOOKFA is a junction box designed to power undercabinet light fixtures. It is suitable for indoor dry locations only and has a maximum linear run of 255W. It comes with a 3/8" wire connector and two captive screws for mounting. The junction box also has alternate knockouts for electrical supply and a jumper cable can be ordered separately. To install the junction box, remove the cover screws, prepare the electrical wire(s), attach the 3/8" wire connector to the junction box, and secure the junction box to the mounting surface using the captive screws.

RAB Lighting JBKNOOKFA is a junction box designed to power undercabinet light fixtures. It is suitable for indoor dry locations only and has a maximum linear run of 255W. It comes with a 3/8" wire connector and two captive screws for mounting. The junction box also has alternate knockouts for electrical supply and a jumper cable can be ordered separately. To install the junction box, remove the cover screws, prepare the electrical wire(s), attach the 3/8" wire connector to the junction box, and secure the junction box to the mounting surface using the captive screws.

JBKNOOK
INSTALLATION INSTRUCTIONS
KNOOK FA UNDERCABINET
®
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
Knockout
Electrical Port
Junction Box Cover
Screws(2)
JBKNOOKFA
Alternate
Knockouts
3/8” Wire Connector
(supplied)
Junction Box
Fixture
Jumper Cable
(Ordered seperately)
On-O Switch
Junction Box
Cover
Clamping
Screws (2)
Lock Nut
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
WARNING: Make certain power is OFF before installing or
maintaining fixture. No user serviceable parts inside.
WARNING: Risk of fire or electric shock. Suitable For Indoor Dry
Locations Only.
WARNING: To prevent overheating do not install in small
enclosed spaces.
WARNING: Do not install this product in an environment outside
the listed ambient temperature( -20°C to +40°C).
WARNING: 255W maximum linear run, do not use this Junction Box
to provide power to other products.
SAFETY INSTRUCTIONS
The fixture is suitable for indoor dry locations only.
1. Remove Junction Box Cover Screws (2) and remove Cover.
Save Screws.
2. Prepare electrical wire(s) (supplied by stripping conductor ends
approximately 3/8”).
3. For installation using 3/8” Wire Connector (supplied) determine
mounting orientation and remove one KNOCKOUT on desired
side of Junction Box for electrical supply and attach 3/8” Wire
Connector to Junction Box as shown. Outer wire jacket must
protrude through 3/8” Wire Connector to adequately protect
internal conductors.
4. Secure 3/8” Wire Connector to Junction Box by tightening
the Locknut then tightening Clamping Screws(2) on electrical
connector fitting securely.
5. Push stripped wire(s) ends into PUSH-IN WIRE CONNECTORS
(see WIRING DIAGRAM). Push excess electrical supply wire(s)
back into wall.
6. Secure Junction Box to mounting surface using (2) Captive
Screws (supplied), be careful not to drive screws all the way
through the cabinet bottom. Use shorter screws if neccessary
(supplied by others).
7. Replace and secure Junction Box Cover with supplied screws.
8. Follow installation instructions provided with undercabinet
light fixture for mounting and connector options.
9. Before powering on make sure that all fixtures connected to
Junction Box have been properly installed and that all open
Electrical Ports on the Junction Box and fixtures are safely
covered with Electrical Port Covers.
MOUNTING INSTRUCTIONS
MOUNTING INSTRUCTIONS CONT
Captive
Screws (2)
JBKNOOK
INSTALLATION INSTRUCTIONS
KNOOK FA UNDERCABINET
®
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install
and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
JBKNOOKFA IN-0420
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly - [email protected]
Free Lighting Layouts
Answered online or by request
© 2020 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation or
maintenance.
LIGHT
FIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GROUND
73692-RAB
Make sure the supply voltage is the same as the luminaire voltage,
see fixture spec label.
1. Connect the black fixture lead to the LINE supply lead.
2. Connect the white fixture lead to the COMMON supply lead.
3. Connect the GROUND wire from fixture to supply ground.
ONOFF WIRING
CAUTION: Be sure fixture temperature is cool enough to touch.
Do not clean or maintain while fixture is energized.
1. Clean polycarbonate lens with non-abrasive glass
cleaning solution.
2. Do not open fixture to clean the LED. Do not touch the LED.
CLEANING & MAINTENANCE
1. Check that the line voltage at fixture is correct. Refer to
wiring directions.
2. Is the fixture grounded properly?
TROUBLESHOOTING
DIMENSIONAL DRAWINGS
1”
8”
3 5/8”
3 5/8”
8”
1 1/4”
1 1/8”
1”
  • Page 1 1
  • Page 2 2

RAB Lighting JBKNOOKFA Operating instructions

RAB Lighting
Brand
RAB Lighting
Model
JBKNOOKFA
Category
Decorative lighting
Type
Operating instructions
This manual is also suitable for

RAB Lighting JBKNOOKFA is a junction box designed to power undercabinet light fixtures. It is suitable for indoor dry locations only and has a maximum linear run of 255W. It comes with a 3/8" wire connector and two captive screws for mounting. The junction box also has alternate knockouts for electrical supply and a jumper cable can be ordered separately. To install the junction box, remove the cover screws, prepare the electrical wire(s), attach the 3/8" wire connector to the junction box, and secure the junction box to the mounting surface using the captive screws.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents