Metra 95-7424 is a car installation kit that allows you to seamlessly integrate a double DIN radio or stacked ISO mount units into your 2008-2011 Nissan Titan. It provides a sleek, factory-like finish, matching the silver color of your dashboard. The kit includes all the necessary hardware and brackets to secure your new devices, making the installation process a breeze.
Metra 95-7424 is a car installation kit that allows you to seamlessly integrate a double DIN radio or stacked ISO mount units into your 2008-2011 Nissan Titan. It provides a sleek, factory-like finish, matching the silver color of your dashboard. The kit includes all the necessary hardware and brackets to secure your new devices, making the installation process a breeze.
INSTALLATION INSTRUCTIONS FOR PART 95-7424
95-7424
APPLICATIONS
Nissan Titan 2008-11
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted Silver To Match Factory Dash
A) Double DIN Radio Housing • B) Double DIN Trim Plate • C) Double DIN Brackets • D) Trim Panel
• E) Two Sided Tape (Not Shown)
Harness & Antenna Connections (sold separately)
• 70-7550 - Nissan Harness 95-up
KIT COMPONENTS
A
TOOLS REQUIRED:
Torx T-10 Driver • Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
C
D
B
Dash Disassembly
Nissan Titan 2008-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 2
Kit Assembly
- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Final Assembly
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TABLE OF CONTENTS
95-7424
*Note:
Refer also to the instructions included with the aftermarket radio.
95-7424 DASH DISASSEMBLY
NISSAN Titan 2008-11
A
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip the entire dash panel including
the radio and climate controls. Unplug
and remove the panel.
(Figure A)
2
Remove (4) Phillips screws securing
the radio chassis. Unplug and remove
the chassis.
(Figure B)
3
Remove (4) T-10 Torx screws securing
the climate controls to the dash panel
and remove the controls from the
panel. (Retain the screws and climate
controls for re-use during kit prepara-
tion.)
(Figure C)
4
Remove (2) T10 Torx screws securing
the passenger air bag status light
assembly to the dash panel and
remove the light from the panel.
(Retain the screws and light for re-
use during kit preparation.)
(Figure C)
NOTE:
The small round Airbag sticker
also needs to be removed from the fac-
tory panel and placed onto the 95-7424
radio housing panel. (A round piece of
double-sided tape is provided in case
the factory sticker is not strong
enough.) (Figure C)
5
Continue to kit preparation
2
95-7424 KIT PREPARATON
Attach the climate controls to the Trim
Panel using the factory hardware
removed during the dash disassem-
bly.
(Figure A)
1
Attach the passenger air bag status
light assembly to the Trim Panel using
the factory hardware removed during
the dash disassembly.
(Figure B)
Also, apply to air bag button the small
round airbag sticker previously
removed in Step 5 dash disassembly.
(Figure B)
2
Continue to kit assembly.
A
B
NISSAN Titan 2008-11
3
95-7424 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
Snap the Double DIN brackets to the
inside edge of the Double DIN radio
housing.
(Figure A)
1
Snap the Double DIN trim-plate onto
the housing/radio assembly.
(Figure B)
3
Slide the Double DIN radio into the
Double DIN bracket/radio housing
assembly and secure the radio to the
assembly using the screws supplied
with the radio.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
4
95-7424 KIT ASSEMBLY
A
B
STACKED ISO MOUNT UNITS PROVISION
Snap the Double DIN brackets to the
inside edge of the Double DIN radio
housing.
(Figure A)
1
Slide the stacked ISO mount units into
the Double DIN bracket/radio housing
assembly and secure the units to the
assembly using the screws supplied
with the units.
(Figure B)
2
Snap the Double DIN trim-plate onto
the housing/radio assembly.
(Figure B)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
5
95-7424 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble in reverse order of disassembly using the 95-7424 Trim Panel in
place of the factory radio trim panel.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
95-7424 INSTRUCTIONS
1-800-221-0932
REV. 11/18/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST95-7424
www.metraonline.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Metra 95-7424 is a car installation kit that allows you to seamlessly integrate a double DIN radio or stacked ISO mount units into your 2008-2011 Nissan Titan. It provides a sleek, factory-like finish, matching the silver color of your dashboard. The kit includes all the necessary hardware and brackets to secure your new devices, making the installation process a breeze.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Metra Electronics 99-7337B User manual
-
Metra Electronics 997416 User manual
-
Metra Electronics 95-7416G User manual
-
Metra Electronics 95-5822B User manual
-
PAC BKNDK7312 Operating instructions
-
Metra Electronics 99-9223 User manual
-
GE JXS81WW Installation guide
-
Metra Electronics 99-7426 User manual
-
Metra Electronics 99-7423 User manual
-
Metra Electronics LEXUS ES 95-8150 User manual
