TEAC LPU192CD User manual

Brand: TEAC

Model: LPU192CD

Category: Audio turntables

Type: User manual

USER MANUAL

IMPORTANT !

LPU192CD

Hi-Fi Turntable Stereo System

WARRANTY INFORMATION INSIDE. PLEASE READ

Trademark of TEAC Corporation JAPAN

www.teac.com.au

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualifed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

Read these Instructions.

Keep these Instructions.

Heed all Warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifers) that produce heat.

Do not defeat the safety purpose of the polarized or

grounding - type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety.

When the provided plug does not ft into your outlet,

consult an electrician for replacement of the obsolete

outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11 Only use attachments/accessories specifed by the

manufacturer.

12.

Important Safety Instructions

Use only with a cart, stand, tripod,

bracket, or table specifed by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

Control Location

Dust Cover

Turntable

Tone arm

DC input

AUX output (L)

AUX output (R)

SOURCE button

P-MODE/MEM button

VOLUME Control

POWER button

RECORD button

+10 / FOLDER+ button

CD Compartment

LCD Display

M+ / button

M- / button

TUN+/-

Controls

AUX input

USB port

OPEN / CLOSE button

REAR SIDE

FRONT SIDE

45 RPM Adaptor

Tone arm control lever

Auto stop control switch

Speed selector

Hold Down Clip

Tone arm rest

This unit operates using the supplied AC Adapter (Operate at 240 V ~ 50Hz)

Connecting AC Adaptor

NOTE: Only use the supplied adapter.

1. Plug the AC adaptor into normala power outlet socket.

2. Insert the DC plug of the AC adaptor cord into the DC IN Jack at the back of the unit.

Switching On for the first time

Plug into AC power by following instructions on the previous Connecting AC adaptor

section. Press the POWER button to turn on the unit. The LCD Display will light up.

To turn the unit off, press the POWER button again.

Switching between different sources (Radio/CD/USB/PHONO/AUX)

After turning on the unit, press and toggle SOURCE button to switch between different

sound sources.

Adjusting sound volume level

After turning on the unit, turn the VOLUME control to adjust the level of sound volume.

Power Source

WARNING! THIS PRODUCT USES A CLASS 1 LASER. AVOID ANY DIRECT

EXPOSURE TO THE LASER BEAM. USE OF CONTROLS, ADJUSTMENTS OR

PROCEDURES NOT LISTED IN THIS GUIDE MAY RESULT IN HAZARDOUS

EXPOSURE.

Handling Compact Discs

To remove a CD from its storage case, press down on the center of case

and lift the disc out.

Hold the disc by the edges. Avoid touching the recorded side of t he disc.

Compatible Compact Discs

Only compact MP3 format discs or music discs identified with

marking shown right can be used with your CD Player.

Loading CDs / MP3 Disc

1. Press and toggle the SOURCE button to s witch to CD mode.

2. Press the OPEN/CLOSE button on the front of the unit to open the CD door.

3. Hold the CDs / MP3 disc by its edge with CD graphical side facing up and put it onto the

CD compartment after the CD door is opened. Make sure that the disc label is facing

up.

4. Press the OPEN/CLOSE button again to close the CD door a nd make sure the

VOLUME control is not in minimum position.

CDs / MP3 Disc playback

After loading the disc, the d isc will begin spinning and the total number of the tracks on the

disc will be shown on the display.

USB Device Playback (MP3 file only)

1. Press and toggle the SOURCE button to switch to USB mode.

2. Insert the USB device into the USB port. The LCD display shows “- - - -“ afor few

seconds,

the total music files number show on display.

3. Make sure the VOLUME con trol is not in minimum position.

4. When removing USB

device, press the

M-

/ button to stop playingfirst .

Play / Pause Control

Press the M+ / button to play the CDs / MP3 Disc / USB. To pause p layback

temporarily by pressing again the M+ / button. Music playback will be paused and the

current elapsed track time will be shown and blanking on the display. Press the M+ /

button again to resume playback.

Remark:

If there is no disc in the unit, “NO” or “ERR” will be indicated on the display.

If the CD ca nnot b e read, “NO or ERR” will be indicated on the dis

Operate the CDs / MP3 Disc / USB

Care And Maintenance of Disc

MP3

Disc

Stop playback

To stop playback, press the M- / button on the unit. The total number of tracks of the

CDs / MP3 Disc / USB will be displayed.

Skip track

During playback, tune the TUN+ / or TUN- / controls to skip to the next or previous

tracks.

High-speed music search

During playback, tuning and hold the TUN+ / or TUN- / controls to skip/search

through the current track at high speed in forward or backward directions. When the TUN+ /

or TUN- / controls are released, normal playback speed will be resumed

immediately.

+10 / FOLDER+ skip control

During playback, press the +10 / FOLDER+ button to skip to next folder. Press and hold the

+10 / FOLDER+ button to skip up by 10 tracks if destination track is inside the folder.

Repeat playback modes (Repeat 1 / Repeat Folder / Repeat all)

During playback, press the P-MODE / MEM button until the REP1 icon is displayed to

select the current track to be repeated. The selected track will be repeated continuously.

Repeat the Current Track

Repeat All Tracks

During playback, press the P-MODE/ MEM button until the ALL icon is displayed. All

tracks/files on the CDs / MP3 Disc/ USB will be repeated continuously.

Repeat Folder (for MP3 disc only)

During playback, press the P-MODE/ MEM button until the FOLDER icon is shown on the

display. All tracks/files inside the desired folder will be repeated continuously.

Note: REPEAT FOLDER – this function is not available for normal music CD.(Only for MP3

Disc / MP3 files on USB flash-drive)

Programmed CDs / MP3 Disc / USB playback

Return to normal playback

Press the P-MODE/ MEM button until NO repeat indicator is displayed. The normal

playback will be resumed.

This unit can be programmed to play up to 20 tracks in CD / USB mode. Load the music CD

disc onto the CD compartment.

1. Press P-MODE/ MEM button once in the stop mode. “P-01” will be shown on the display

and blinking.

2. Tune the TUN+ / or TUN- / controls to select the desired track to be

programmed.

3. Press P-MODE/ MEM button again to confirm the selected track.

4. Repeat steps 2-3 to program up to 20 tracks.

5. Press the M+ / button to play the programmed tracks after programming is

completed. The “PROG” icon will be displayed during the programmed playback.

6. Tune the TUN+ / or TUN- / controls repeatedly until you reach the desired

programmed tracks number.

7. To clear program and resume normal playback, press the M- / button twice during

playback, or open the CD door, or change to next mode to clear the programmed tracks.

The unit is designed to receive FM Stereo radio band.

USB RECORDING From CD Disc

uning the FM Radio

Record for one song

1. Insert the USB stick into the USB port.

Record for more than one song and maximum to 20 songs

1. Insert the USB stick into the USB port.

2. Press “Source” button to CD mode.

3. Insert the CD disc into the CD tray.

4. After loading, the total number of the tracks will be shown on the display.

5. Press P-MODE/MEM button, “P-01” will be shown on the display and blinking.

6. Tune the or button to select your desired song

7. Press P-MODE/MEM button,to confirm the selected song.

8. Repeat the step 5 – 7 to program up to 20 songs.

9. Press the “RECORD” button , “REC” will be shown on the display and start recording.

10. Recording will be completed and stopped automatically at the last selected song or

press “RECORD” button to stop recording immediately.

2. Press “Source” button to CD mode.

3. Insert the CD disc into the CD tray.

4. After loading, the total number of the tracks will be shown on the display.

5. Tune the or button to select your recording song.

6. Press the “RECORD” button , “REC” will be shown on the display and start recording.

7. Recording will be completed and stopped automatically at the end of the song or

press “RECORD” button to stop recording immediately.

. Press and toggle the SOURCE button on the front of the unit to switch to FM Radio

mode. “FM” will appear on the display.

2. Adjust the TUN+ / or TUN- / controls on the front of unit to tune the frequency of

desired radio station.

3. The tuning frequency will appear on the LCD display.

4. To turn off the unit power, press the button to switch off the unit.

Remark:

The unit can store up to 2 0 tracks in the programmable memories. During the

programmed playback, user can still select the “repeat 1 / repeat all” functions.

RADIO Operation

Gently open the dust cover.

1. Lift the dust cover all the way up until it stop, the cover will now stay open.

2. Remove white protective needle cover by gently pulling towards the front of the unit.

3. Release tone arm HOLD DOWN CLIP by gently pushing to the right. This will unlock

TONE ARM from its arm rest. Re-lock the HOLD DOWN CLIP when moving the unit to

another location.

Turntable Operation

1. Press and toggle the SOURCE button on the front of the unit to switch to PHONO

mode.

2. Set the SPEED SELECTOR to the correct speed (33, 45 or 78rpm).

3. Place the record on the turntable.

4. Move the TONE ARM to the desired starting point on the record. The record will start

playing.

5. Turn the VOLUME CONTROL to adjust the volume to the desired level.

6. Slide the AUTO STOP CONTROL SWITCH to choose the auto stop function.

NB:

Sound output of the built-in amplifier is limited, when playing records, to avoid feedback

and rumble. This is normal, so keep the volume as low as possible on the unit, and rather

increase volume on external amplifier.

. At the end of the record, the TONE ARM will stop automatically. You must return the

TONE ARM to TONE ARM REST manually.

PHONO Operati on

Saving an FM Radio Station

1. Follow the instructions for Tuning the FM Radio.

2. Adjust the TUN+ / or TUN- / controls to tune the FM radio to the desired

station.

3. Press the P-MODE / MEM button on the front of unit, flash MEM icon and preset

number P01 will appear on the LCD display, indicating which preset the current station

will be saved to.

4. Press the M+ / or M- / buttons to select preset number.

5. Press again the P-MODE/MEM button to confirm saved.

6. Repeat above steps 2 - 5 to preset up to 20 stations.

7. To retrieve one of the preset stations already programmed, press M+ / or M- /

buttons repeatedly until you reach the desired program number of the station.

USB RECORDING From Turntable

etting up (AUX IN) connection

AUX-IN jack will allow you to connect external music player or external sound source to the

main unit.

1. Insert the USB stick into the USB port.

2. Press “Source” button to PHONO mode.

Place the record on the turntable and move the TONE ARM to your desired song to

start playing.

Press the “RECORD” button , “REC” will be shown on the display and start recording.

5. Press “RECORD” button to stop recording.

. Plug into a 3.5mm audio cable (not included) into your external music player and

connect the other end (3.5mm jack) into the AUX IN jack on the front of the unit.

2. Make sure your external music player is turned on.

3. Press and toggle the SOURCE button to switch to AUX mode on the unit.

4. Start music playb

ack on your external music player.

5. Adjust VOLUME control to control the sound level of music playback from the speakers

on the unit.

1. You can run the audio from the unit into your home stereo, television or other stereo

source by using the AUX output.

2. To make this connection, you need a standard RCA cable (not included). Plug the red

and white connectors on one end of the cable into the red and white AUX OUT jack on

the rear of the

unit. The other end of the cable will plug into the AUX INPUT jacks of

your selected component.

3. Operate the unit as usual, you can hear the sound produced by the unit.

NOTE: You can still listen to your unit when using the Audio Output feature.

AUX IN Operation

AUX OUT Operation

ADAPTER for 45 RPM (Accessory)

This adaptor allows you to play 45 RPM records.

1. Place the 45 RPM ADAPTER over the spindle.

2. Gently place your 45 RPM record onto the turntable.

3. Follow the steps under turntable operation to play you record.

Power Output. . . . . . . . . . . . . . . . . .

Speakers . . . . . . . . . . . . . . . . . . . . . .

0.8 watt RMS x 2 channels (Turntable Section)

1.5 watt RMS x 2 channels (CD, USB, RADIO,

AUX-IN Section)

4 Ohms 5W x 2

CD Disc- Disc Diameter . . . . . . . . . .

120mm / 80mm

Record Speed. . . . . . . . . .. .. . . . . . .

33 1/3, 45 or 78 RPM

AC Adapter input . . . . . . . . . . . . . . .

AC 100 - 240V 50/60Hz

DC INPUT . . . . . . . . . . . . . . . . . . . .

DC9V 1.5A

Radio Frequency. . . . . . . . . . . . . . .

FM: 87.5 – 108MHz

USB . . . . . . . . . . . . . . . . .. . . . . . . . .

Support USB flash-drive up to 16GB

Dimensions (H x W x D) . . . . . . . . .

370mm(W) x 153.5mm(H) x 383mm(D)

IMPORTA

NT: Due to continual revision and improvement on our products design,

specifications are subject to change without further notice.

Specifications

In the event of a product failure within the warranty period, please call the

TEAC Warranty Service Hotline

1300 553 315

Between Monday to Friday - 8.30AM to 5PM AEST

*Please have your purchase receipt and the product’s serial number ready

For other enquiries and support please visit

www.teac.com.au

TEAC LPU192CD User manual

Brand: TEAC

Model: LPU192CD

Category: Audio turntables

Type: User manual

Download PDF

report

TEAC LPU192CD User manual

TEAC LPU192CD User manual

Related papers

Other documents