USER MANUAL
WARRANTY INFORMATION INSIDE. PLEASE READ
www.teac.com.au
IMPORTANT !
Trademark of TEAC Corporation JAPAN
Stereo Turntable with Bluetooth OUT & USB Encoding
TTDEDS2018T
INITIAL SET-UP
MAINS CONNECTION
Ensure that the mains voltage of your home corresponds to the operang voltage of the unit.
Your unit is ready to be connected to a mains voltage of 220V-240V/50Hz.
AMPLIFIER CONNECTION
Whilst you can listen to your new turntable using the built-in speakers, you may wish to con-
nect it to your exisng Hi Fi system. Connect the audio plugs to the AUX input on your mixer or
amplier using an RCA cable (not supplied).
Red plug into R/H channel input.
White plug into L/H channel input.
Playing a record
Place the record on the turntable. If required, also place the adaptor on the record spindle.
Choose the desired playing speed using the speed selecon switch between 33.3, 45 and 78rpm.
Turn on the Rotary Power Switch, note that this also controls volume.
Release the tone arm lock.
Raise the arm with your hand lightly.
Place the stylus vercally over the rst track of the record, the turntable will start turning auto-
macally.
Lower the stylus slowly onto the record to play.
When a record comes to the end, the turntable will stop automacally if the auto-stop switch is
in the ON posion. If the switch is in the o posion then it will keep revolving unl the tone arm
is returned to the tone arm rest.
Li up the tone arm and put it on the rest when nished.
Replace the protecve cap on the stylus and close the tone arm lock.
Turn o the power at mains.
Listening to USB/SD tracks
Turn the volume knob in a clockwise direcon to switch on the turntable.
Use the funcon selector to select USB/SD mode.
Insert the USB/SD card into the correct slot.
Wait for 6-10 seconds. Once the unit reads the total tracks, it will auto-play them.
Press “FUNCTION” buonww to convert the USB/SD Tracks. (default for U-disc play)
Press “Play/PAUSE SEARCH” to Pause, press again to play.
Press “PREV” to play previous track.
Press “NEXT” to play next track.
Keep pressing “PREV” for 3 seconds to decrease the playback volume of source-disc.
Keep pressing “NEXT” to increase the volume.
Press “DEL” to delete recorded songs but not original songs in USB or SD card
Note:
1– Without USB / SD card, the default seng is Phono playing.
2– With USB / SD card, the default seng is SD card playing.
1 – Plasc dust cover
2 – Turntable
3 – Adaptor - Use it when playing 45rpm
re c o rd s wi t h c u t ou t c e nt r e s .
4 – Tone arm
5 – Tone arm li lever
6 – On / OFF Phono play Funcon
selecon.
7 – Speed selecon - Three speeds for
choice: 33.3, 45, 78 rpm.
8 – Full range loud speaker
9 – Ceramic cartridge with diamond needle
10 – Power on / o switch & volume buon
11 – LED light indicator
12 – USB slot
13 – SD / MMC card slot
14 – PREV buon
15 – Play / Pause /Search buon
16 – Next buon
17 – Funcon buon
18 – LED display
19 – RCA Line out jack
PRODUCT DESCRIPTION
BLUETOOTH OUTPUT
Connecng to Bluetooth Speakers:
1 - Set up your turntable (With Bluetooth Transmier) and Bluetooth speakers. Make sure the
turntable and Bluetooth speakers are not too far apart.
2 - Turn the volume knob clockwise to switch on the turntable. The Bluetooth output function will be
activated. The LED light indicator will flash, which means the unit is ready to pair with the
Bluetooth speaker.
3 - Turn on your Bluetooth speaker and make sure it is available to be connected. The turntable and
Bluetooth speakers will auto-pair and connect (it may take around 10 - 60 seconds depending on
the speaker model). The Indicator light will be blue and stable when connecon is successful.
4 - To stop Bluetooth out connecon, turn off the unit or turn off the Bluetooth speaker.
Important Note:
• Make sure other Bluetooth devices are o, otherwise they may aect the connecon to speaker.
• Make sure to turn on the Turntable Bluetooth before turning on the Bluetooth speakers.
• In some circumstances the Bluetooth connecon may break or disconnect due to signal
interference, moving beyond the maximum connecon distance, or having an object move
between both Bluetooth devices. However, your device will usually reconnect again automacally.
• In some cases, the devices may need to be manually reconnected using the Bluetooth device’s
sengs.
• If you cannot connect your Bluetooth device, the Bluetooth driver may need to be updated to the
latest version.
MAINTENANCE
REPLACING THE STYLUS
-Refer to the gures 1-8
PRODUCT CARE
1. It is strongly recommended to clean your records with an an-stac cloth to enjoy the best
sound and ensure they are long lasng.
2. For best playback results, it is recommended to replace your stylus periodically
(approximately every 250 hours).
3. Dust the stylus from me to me using a very so brush dipped in alcohol
(brushing from back to front of the cartridge)
4. WHEN TRANSPORTING YOUR RECORD PLAYER, DO NOT FORGET TO:
Replace the protecve cap on the stylus.
Put the rest clip into the pick-up arm.
5. Only store and operate this turntable in a dry and well-venlated environment.
6. Do not place naked ame sources, such as lit candles on or near the device.
7. Do not expose the turntable to dripping or splashing water.
PRODUCT SPECIFICATIONS
• Belt Drive Turntable with DC Motor
• 3 Speed Turntable – 33⅓, 45, 78 RPM
• Plays 7”, 10”and 12”records
• Bluetooth Input
• Built-in stereo speakers - 4Ω, 3W x 2
• Line out to connect to amplier
• Unit dimensions: 379 x 163 x 330mm
• Unit weight: 2.25 kg
• Output power: 7W
TERMS AND CONDITIONS
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entled to a replacement or refund for a major failure and for compensaon for any
other reasonably foreseeable loss or damage. You are also entled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
1. TEAC warrants that this product is free from defects in material and workmanship under
normal domesc use with reasonable care and skill. Maintenance and cleaning (i.e. laser head) is
not covered by this warranty. The TEAC warranty only applies to TEAC products purchased NEW
from a TEAC Authorised Retailer in Australia. This warranty only applies to the original purchaser
and cannot be transferred.
2. The benets to the consumer given by this Warranty are in addion to other rights and
remedies of the consumer under a law in relaon to goods or services to which the warranty
relates, being the Australian Consumer Law.
3. Refund or replacement via your TEAC Authorised Retailer is available for a period of 14 days
aer purchase for goods that have been inspected and determined to have a major failure.
Refund and exchange is not applicable for change of mind.
4. Subject to the terms herein, this warranty eecvely covers TEAC products under the 12
Month Replacement Warranty Scheme, 12 months from the date of original purchase.
5. The warranty is void and warranty claims may be refused, subject to the Australian Consumer
Law, if:
a) The product was not transported, installed, operated or maintained according to manufacturer
instrucon, or
b) The product was abused, damaged, tampered, altered or repaired by any unauthorised
persons,
or
c) Product failure is due to accidents during use, installaon or transit, power surges, use of
defecve or incompable external devices, exposure to abnormal condions such as excessive
temperatures or humidity, or entry of liquids, objects or creatures into the product, cockroach
infestaons, or
d) The customer is unable to provide proof of purchase of the product for vericaon, or
e) The serial number of the product is missing or has been tampered with.
6. No one is authorised to assume any liability on behalf of TEAC or impose any obligaon on it,
in connecon with the sale of any equipment other than as stated in this warranty and outlined
above.
7. TEAC and/or its Authorised Service Centres reserve the right to inspect and verify whether the
product is exhibing a major failure as claimed by customers/retailers.
Call us between Monday to Friday - 8.30AM to 5PM
AEST
*Please have your purchase receipt and the product's
serial number ready
For other enquiries and support please visit
www.teac.com.au
TEAC Warranty Service Hotline
1300 553 315
/
