BMW 65 12 0 140 745 Installation Instructions Manual

BMW
Brand
BMW
Model
65 12 0 140 745
Category
Signal cables
Type
Installation Instructions Manual

This manual is also suitable for

Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 574
BMW Parts and Accessories
Installation Instructions
BMW CD changer installation kit
BMW 5 Series Saloon (E
39)
• These installation instructions are only valid for cars with a production date before 09/01
Technical and electrical knowledge required
The installation time is 0.5 - 3.5 hours but this may vary depending on the condition of the car
and the equipment in it.
Retrofit/Installation kit No. 65 12 0 029 649
65 12 0 029 591
65 12 0 140 744
65 12 0 140 745
F 39 0897 B
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2002
Installation Instructions No. 01 29 0 029 574
Contents
Section Page
1. Important information on installing the CD changer in the E39 . . . . . . . . . . . . . . . . 3
2. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. To install the CD changer (cars without an on-board monitor, without
a DSP amplifier and with Professional radio SA663 up to production date 02/01 only)
10
7. To install the CD changer (cars without an on-board monitor, without
a DSP amplifier and with Professional radio SA663 after production date 03/01 only)
15
8. To install the CD changer (cars with an on-board monitor radio and without
a DSP amplifier only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9. To install the CD changer (cars without an on-board monitor radio and with
a DSP amplifier only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10. To install the CD changer (cars with an on-board monitor radio and with
a DSP amplifier only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11. To install the CD changer (cars without an on-board monitor radio and with
CD changer preparation only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
12. To install the CD changer (cars with an on-board monitor radio and with
CD changer preparation only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
13. Coding and concluding work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
14. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
15. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
EN/3
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
1. Important information on installing the CD changer in the E39
Only for use in the BMW dealer organisation.
The CD changer may only be installed by a specialist workshop that has the required special
tools and manuals (servicing, repair, diagnostics, etc.).
All the work is shown for the left-hand side of the car and must be repeated on the right-
hand side.
In cars with an on-board monitor radio the control cable is only installed in the boot.
In cars with a BMW Professional hi-fi system DSP amplifier only the coaxial cable for the
Professional hi-fi system DSP amplifier/CD change must be installed in the boot.
In cars with a small boot cover the boot cover for the CD changer may have to be ordered
separately from the electronic parts catalogue (EPC), depending on the equipment in the
car.
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
Additional cables/leads that you install must be secured with cable ties.If the specified PIN
chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
Subject to technical modifications
Required tools and equipment
Set of flat screwdrivers Set of Allen keys
Set of Philips screwdrivers Drill
Angle cutter Set of drill bits
1/4 inch socket set 1/2 inch socket set
Cable lamp Set of step drill bits
BMW disconnection tool Set of Torx sockets
Hot air blower
EN/4
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
2. Preparations
TIS
instruction
No.
Print out error memory -
Disconnect the battery 12 00 ...
Remove the left boot trim 51 47 ...
Additional preparations for cars without
Professional hi-fi system DSP amplifier and on-board monitor:
Remove the front left seat 52 13 000
Remove the door sill strips at the front and rear left. 51 47 030
51 47 000
Remove the B pillar trim on the left 51 43 148
Remove the rear seat bench and rear seat backrest 52 24 005
52 24 010
Remove the front left centre console -
Remove the components in the centre console (radio, cassette, heating/air
conditioning control) to release the centre console and push it back a little
61 31 057
EN/5
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
3. Parts list
12
22 23
24
13 14 15 16 17
2519 20 21
11
10
9
4
5
6
7
8
3
2
1
18
F 39 0898 B
EN/6
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
3. Parts list
1 CD changer
2 Strut***
3 Shrink hose*/****
4 Power supply cable
5 CD changer control cable (4210 mm)*/**
6 CD changer control cable (550 mm)*/***
7 CD changer coaxial cable (650 mm)******
8 CD changer adapter cable*/****
9 Base holder**
10 CD changer holder**
11 Front CD changer holder***
12 Expanding nut
13 Hexagonal nut with washer M6 (2x)
14 Washer
15 Bush (2x)
16 Cap nut M5 (2x)
17 Speed nut M5 (6x)
18 Hexagonal screw with washer M5x14 (6x)
19 Hexagonal screw with washer M6x20
20 Fillister head Philips screw (4x)
21 Hexagonal self-tapping screw
22 Cable tie (L=292 mm W=4 mm) (20x)
23 Cable tie (L=200 mm W=3 mm)
24 Socket casing (2x)
25 Retaining clip*****
* Part not required for cars with a DSP amplifier
** Part not required for cars with an on-board monitor radio with a production date after 09/01
*** Part not required for cars without an on-board monitor radio
with a production date after 09/00
**** Part not required for cars with a Professional radio SA663
with a production date before 02/01
***** Part only required for cars with a Professional radio SA663
with a production date before 02/01
****** Part only required for cars with a DSP amplifier
EN/7
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
4. Connection overview
Power supply cable
A
is only required if the black 3-pin socket casing on the CD changer power
supply is not tied back on the audio wiring harness.
Item Description
Cable
colour
Connection location in the car
Dimensions: Power supply cable
---- ----
A1
Black 1-pin plug casing
X6500
with
twin-lead terminal I-BUS
white/grey/
yellow
To audio systems plug connector
X322B
in the boot on the
left side panel, white 12-pin socket casing
PIN4
, white/grey/
yellow cable
A2
Black 1-pin plug casing
X6501
with
double assignment terminal 30A56
red/green To audio systems plug connector
X322B
in the boot on the
left side panel, white 12-pin socket casing
PIN1
, red/green
cable
A3
Cable eyelet, 6 mm in diameter
terminal 31
brown Earth post in the left tail light
A4
Black 3-pin socket casing
---
Power supply connector
X18180
for CD changer in the boot
on the left
24
Black 1-pole socket casing
---
To the disconnected socket contacts from the audio systems
plug connector
X322B
in the boot on the left side panel
A
C
B
D
E
24
A1
B1
B2
C2
D2
C1
D1
E1
A4
E2
A2
A3
F 39 0899 B
EN/8
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
4. Connection overview
Control cable
B
is
only
required for cars without an on-board monitor and without a Professional
hi-fi system DSP amplifier
Control cable
C
is
only
required for cars with an on-board monitor and without a Professional
hi-fi system DSP amplifier
Coaxial cable
D
is
only
required for cars with a Professional hi-fi system DSP amplifier
Adapter cable
E
is
only
required for cars without a Professional hi-fi system DSP amplifier.
Adapter cable
E
is not required for cars with Radio Professional radio SA663 with a production
before 02/01.
Item Description
Cable
colour
Connection location in the car
B Control cable
Radio/CD changer
--- ----
B1
Silver 10-pin socket casing
---
To silver 10-pin plug casing
E2
on the adapter cable or, on
cars with a Professional radio SA663 with a production date
before 02/01, to the black 17-pin radio socket casing
B2
Black 6-pin socket casing
---
To the CD changer in the boot on the left
Item Description
Cable
colour
Connection location in the car
C Control cable
On-board monitor radio/CD changer
--- ----
C1
Silver 10-pin socket casing
---
To silver 10-pin control casing
E2
on the adapter cable
C2
Black 6-pin socket casing
---
To the CD changer in the boot on the left
Item Description
Cable
colour
Connection location in the car
D Coaxial cable
---- ----
D1
Angled coaxial socket casing
---
To the Professional hi-fi system DSP amplifier in the boot on
the left
D2
Coaxial socket casing
---
To the CD changer in the boot on the left
Item Description
Cable
colour
Connection location in the car
E Adapter cable
---- ----
E1
White 12-pin socket casing
---
To new generation connection plug on the radio
E2
Silver 10-pin plug casing
---
To silver 10-pin socket casing on the control cable
B
or
C
EN/9
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
5. Installation and cabling diagram
0
The power supply wiring harness
A
, the control cable
B
, the control cable
C
, the coaxial cable
D
and the adapter cable
E
are to be installed as shown in the figure and secured with cable ties.
When installing the power supply wiring harness
A
start with branches
A1
and
A2
.
Branches
A1
and
A2
to the left side panel in the boot
Branch
A3
to the left tail light
Branch
A4
to the CD changer in the boot on the left
Branch
B1
to the installation site of the radio / connect to branch
E2
Branch
B2
to the CD changer in the boot on the left
Branch
C1
to the installation site of the radio / connect to branch
E2
Branch
C2
to the CD changer in the boot on the left
Branch
D1
to the DSP amplifier in the boot on the left
Branch
D2
to the CD changer in the boot on the left
Branch E1 to the new generation connection plug on the front of the radio or the new generation
connection plug in the boot on the left
Branch E2 to branch B1 or branchC1
B1
E2
E1
D1
A1+A2
A3
B2
C2
C1
D2
E
B
B
A
A4
D
C
E2
E1
E
F 39 0900 B
EN/10
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
6. To install the CD changer (cars without an on-board monitor, without a DSP
amplifier and with Professional radio SA663 up to production date 02/01 only)
0
0
0
The installation of the power supply cable A
for the CD change is only necessary, if the
black 3-pin socket casing X18180 on the
power supply for the CD changer is not tied
back on the audio wiring harness.
0
Disconnect the white 12-pin plug connector X322.
Disconnect the existing socket contact from slot
PIN4, white/grey/yellow cable on the white 12-pin
socket casing X322B.
Connect branch A1, 1-pin socket contact, white/
grey/yellow cable on the power supply cable A to
the white 12-pin socket casing X322B in slot
PIN4.
Connect the supplied 1-pin black socket casing to
the disconnected socket contact and connect it to
branch A1, black 1-pin plug casing, white/grey/
yellow cable.
0
Disconnect the existing socket contact from slot
PIN1, red/green cable on the white 12-pin socket
casing X322B. Connect branch A2, 1-pin socket
contact, red/green cable on the power supply
cable A to the white 12-pin socket casing X322 in
slot PIN1.
Connect the supplied 1-pin black socket casing
on to the disconnected socket contact and
connect it to branch A2, black 1-pin plug casing,
red/green cable. Remove the left tail light.
F 39 0901 B
X18180
A
!
A
X322
A1
F 39 0902 B
A
X322
A2
F 39 0903 B
EN/11
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 up to production date 02/01 only)
0
Remove the left tail light unit.
Mark the drilling position (40) with a centre punch.
Dimension A = 19 mm
Dimension B = 17 mm
Remove the body paint and primer from the grey
area (41) in a diameter of 20 mm around the
position of the hole (40) on the front and rear of the
tail light unit (42).
The panel must be bare in the grey area (41), to
ensure that perfect contact is possible.
Risk of damage. Before drilling the hole
ensure that the cable and plug fastenings are
unclipped and the cables are removed from
the drilling area to prevent their being
damaged.
Drill the holes with a 6 mm drill bit.
Remove all the drill chips that are produced during
the drilling process using an extractor.
Then deburr the edges of the hole.
0
Push the hexagonal screw and washer (19) from
the rear into the hole (40) and secure it with a
hexagonal nut and washer M6 (13).
If you fit the earth connection cable later, ensure
that you fit the washer (14) first and then branch
A3.
Then secure branch A3 (the terminal lug with the
cable output must point downwards) using the
second hexagonal nut and washer M6 (13).
After securing the parts, treat all of them with
the anti-corrosion measures set out in the
BMW standard.
0
The figure shows the final installation position of
the earth connection cable.
The cable loom (40) must point downwards.
F 39 0904 B
41
42
A
B
40
41
!
F 39 0905 B
40
13
13
14
19
A3
!
F 39 0906 B
40
EN/12
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 up to production date 02/01 only)
0
The installation of the control cable B for the
CD changer is only required, if the black
6-pin socket casing X18729 on the control
cable for the CD changer is not tied back on
the audio wiring harness.
0
Lay control cable B along the audio wiring harness
as follows.
Lay control cable B from the radio (40) under the
centre console to the left.
Lay control cable B between the transmission
tunnel and carpet along the audio wiring harness
under the left seat to the B pillar and along the
door sill to the rear window shelf.
0
Thread control cable B through the rubber
grommet (40) into the boot to the installation site of
the CD Changer and secure it with cable ties.
0
Connect branch B1, silver 12-pin socket casing on
the control cable B to the black 17-pin socket
casing X18126 on the radio connection plug and
secure it with a retaining clip (25).
Connect socket casing X18126 to the radio (40).
F 39 0907 B
B
X18729
!
X18126
B1
40
B
F 39 0909 B
40
B
F 39 0910 B
25
B1
B
X18126
40
039 0001 B
EN/13
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 up to production date 02/01 only)
0
The figure shows the boot at the rear left.
Push the expanding nut (12)
into the existing hole (40).
0
Place three speed nuts M5 (17) on to the base
holder (9).
Insert the base holder (9) and secure it with the
hexagonal self-tapping screw (21) and two cap
nuts M5 (16).
0
Remove the three transport guard screws (40)
from the CD changer (1) and seal the apertures
with the adhesive discs supplied (adhesive discs
are supplied with the CD changer).
Remove the two covers (41) and set the
adjustment mechanism (42) with a straight slot
screwdriver to V (vertical installation) and then re-
affix both covers (41).
0
Connect branch A4, black 3-pin socket casing on
the power supply cable A or the standard power
supply plug X18180 to the plug casing on the
power supply connector (40) on the CD changer (1).
Connect branch B2, black 6-pin socket casing on
the control cable B or the standard plug X18729 to
the plug casing (41) on the CD changer (1).
40
12
F 39 0912 B
!
9
16
21
17
16
F 39 0913 B
V
H
V
H
1
42
40
41
41
F 39 0914 B
B2/X18729
41
40
A4/X18180
1
F 39 0915 B
EN/14
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
6. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 up to production date 02/01 only)
0
Insert the CD changer (1) into the holder (10) and
secure it with the four fillister head Philips screws
(20).
Secure the connection cable for the CD changer
(1) with the holder (40) to the hole (41) from the
inside.
Place the CD changer (1) with the holder (10) on
the base holder (9) and secure it with three
hexagonal screws (18).
18
20
20
41
9
40
1
10
F 39 0916 B
EN/15
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
7. To install the CD changer (cars without an on-board monitor, without a DSP
amplifier and with Professional radio SA663 after production date 03/01 only)
0
The installation of the power supply cable A
for the CD change is only necessary, if the
black 3-pin socket casing X18180 on the
power supply for the CD changer is not tied
back on the audio wiring harness.
0
Disconnect the white 12-pin plug connector X322.
Disconnect the existing socket contact from slot
PIN4, white/grey/yellow cable on the white 12-pin
socket casing X322B.
Connect branch A1, 1-pin socket contact, white/
grey/yellow cable on the power supply cable A to
the white 12-pin socket casing X322B in slot
PIN4.
Connect the supplied 1-pin black socket casing to
the disconnected socket contact and connect it to
branch A1, black 1-pin plug casing, white/grey/
yellow cable.
0
Disconnect the existing socket contact from slot
PIN1, red/green cable on the white 12-pin socket
casing X322B.
Connect branch A2, 1-pin socket contact, red/
green cable on the power supply cable A to the
white 12-pin socket casing X322 in slot PIN1.
Connect the supplied 1-pin black socket casing
on to the disconnected socket contact and
connect it to branch A2, black 1-pin plug casing,
red/green cable. Remove the left tail light.
F 39 0901 B
X18180
A
!
A
X322
A1
F 39 0902 B
A
X322
A2
F 39 0903 B
EN/16
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 03/01 only)
0
Remove the left tail light unit.
Mark the drilling position (40) with a centre punch.
Dimension A = 19 mm
Dimension B = 17 mm
Remove the body paint and primer from the grey
area (41) in a diameter of 20 mm around the
position of the hole (40) on the front and rear of the
tail light unit (42).
The panel must be bare in the grey area (41), to
ensure that perfect contact is possible.
Risk of damage. Before drilling the hole
ensure that the cable and plug fastenings are
unclipped and the cables are removed from
the drilling area to prevent their being
damaged.
Drill the holes with a 6 mm drill bit.
Remove all the drill chips that are produced during
the drilling process using an extractor.
Then deburr the edges of the hole.
0
Push the hexagonal screw and washer (19) from
the rear into the hole (40) and secure it with a
hexagonal nut and washer M6 (13).
If you fit the earth connection cable later, ensure
that you fit the washer (14) first and then branch
A3.
Then secure branch A3 (the terminal lug with the
cable output must point downwards) using the
second hexagonal nut and washer M6 (13).
After securing the parts, treat all of them with
the anti-corrosion measures set out in the
BMW standard.
0
The figure shows the final installation position of
the earth connection cable.
The cable loom (40) must point downwards.
F 39 0904 B
41
42
A
B
40
41
!
F 39 0905 B
40
13
13
14
19
A3
!
F 39 0906 B
40
EN/17
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 03/01 only)
Push the shrink hose (3) over branch E2, silver 10-pin plug casing on adapter cable E, and
connect branch B1, silver 10-pin socket casing on control cable B to it.
As you connect B1 to E2 ensure that it is correctly positioned, see figure.
All sharp metal and plastic detents are to be removed from plug connection B1 and E2 using
an angle cutter.
There must be no sharp edges or corners on plug connection B1 and E2.
Push the shrink hose (3) over the plug connection B1 and E2 and shrink it using a hot air blower.
0
The installation of the control cable B for the
CD changer is only required, if the black 6-pin
socket casing X18729 on the control cable for the
CD changer is not tied back on the audio wiring
harness.
F 39 0907 B
B
X18729
!
B1
B1
E2
3
B1
E2
E2
F 39 0908 B
!
!
EN/18
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 03/01 only)
0
Lay adapter cable E with control cable B along the
audio wiring harness as follows.
Connect branch E1, white 12-pin socket casing on
control cable E, to the new generation radio
connection plug X18126in the centre console.
Lay control cable B from the radio (40) under the
centre console to the left.
Lay control cable B between the transmission
tunnel and carpet along the audio wiring harness
under the left seat to the B pillar and along the
door sill to the rear window shelf.
0
Thread control cable B through the rubber
grommet (40) into the boot to the installation site of
the CD Changer and secure it with cable ties.
0
Connect the white 12-pin socket casing (E1) on
adapter cable E to the new generation radio
connection plug (40).
Connect the new generation radio connection
plug (40) and install the radio.
0
The figure shows the boot at the rear left.
Push the expanding nut (12) into the existing hole
(40).
X18126
E1
40
B
E
039 0002 B
40
B
F 39 0910 B
E1
40
E
F 39 0911 B
40
12
F 39 0912 B
!
EN/19
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
7. To install the CD changer (cars without an on-board monitor, without a DSP amplifier and
with Professional radio SA663 after production date 03/01 only)
0
Place three speed nuts M5 (17) on to the base
holder (9).
Insert the base holder (9) and secure it with the
hexagonal self-tapping screw (21) and two cap
nuts M5 (16).
0
Remove the three transport guard screws (40)
from the CD changer (1) and seal the apertures
with the adhesive discs supplied (adhesive discs
are supplied with the CD changer).
Remove the two covers (41) and set the
adjustment mechanism (42) with a straight slot
screwdriver to V (vertical installation) and then re-
affix both covers (41).
0
Connect branch A4, black 3-pin socket casing on
the power supply cable A or the standard power
supply plug X18180 to the plug casing on the
power supply connector (40) on the CD changer
(1).
Connect branch B2, black 6-pin socket casing on
the control cable B or the standard plug X18729 to
the plug casing (41) on the CD changer (1).
0
Insert the CD changer (1) into the holder (10) and
secure it with the four fillister head Philips screws
(20).
Secure the connection cable for the CD changer
(1) with the holder (40) to the hole (41) from the
inside.
Place the CD changer (1) with the holder (10) on
the base holder (9) and secure it with three
hexagonal screws (18).
9
16
21
17
16
F 39 0913 B
V
H
V
H
1
42
40
41
41
F 39 0914 B
B2/X18729
41
40
A4/X18180
1
F 39 0915 B
18
20
20
41
9
40
1
10
F 39 0916 B
EN/20
Retrofit / Installation kit No. 65 12 0 029 649 (others see cover sheet) Issue date: 05.2001
Installation Instructions No. 01 29 0 029 574
8. To install the CD changer (cars with an on-board monitor and without a DSP
amplifier only)
0
The installation of the power supply cable A
for the CD change is only necessary, if the
black 3-pin socket casing X18180 on the
power supply for the CD changer is not tied
back on the audio wiring harness.
0
Disconnect the white 12-pin plug connector X322.
Disconnect the existing socket contact from slot
PIN4, white/grey/yellow cable on the white 12-pin
socket casing X322B.
Connect branch A1, 1-pin socket contact, white/
grey/yellow cable on the power supply cable A to
the white 12-pin socket casing X322B in slot
PIN4.
Connect the supplied 1-pin black socket casing to
the disconnected socket contact and connect it to
branch A1, black 1-pin plug casing, white/grey/
yellow cable.
0
Disconnect the existing socket contact from slot
PIN1, red/green cable on the white 12-pin socket
casing X322B.
Connect branch A2, 1-pin socket contact, red/
green cable on the power supply cable A to the
white 12-pin socket casing X322 in slot PIN1.
Connect the supplied 1-pin black socket casing
on to the disconnected socket contact and
connect it to branch A2, black 1-pin plug casing,
red/green cable. Remove the left tail light.
F 39 0917 B
X18180
A
!
A
X322
A1
F 39 0918 B
A
X322
A2
F 39 0919 B
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

BMW 65 12 0 140 745 Installation Instructions Manual

BMW
Brand
BMW
Model
65 12 0 140 745
Category
Signal cables
Type
Installation Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents