Sans Digital MobileStor MS4UM User manual

Brand: Sans Digital

Model: MobileStor MS4UM

Type: User manual

Introduction

About this Manual

Thank you for choosing Sans Digital products.

The MS4UM will be introduced throughout this manual. It is recommended that you go through this

manual before using Sans Digital products. Although the information has been verified before

published, specifications are subject to change without prior notice. Please refer to

www.sansdigital.com for product specifications or the most recent information regarding Sans

Digital products.

If you have any questions regarding Sans Digital products or need the latest product information,

user manual or firmware, please contact us at 1.800.980.1988 or suppor[email protected] and we

will get back to you as soon as possible.

Table of Contents

MS4UM Package Contents..........................................................................................3

Hardware Installation....................................................................................................3

Installing a Hard Drive in the Removable Tray Module....................................4

USB Connection Support/eSATA Port Multiplier Support...............................5

Windows System Installation.....................................................................................5

Mac System Installation ..............................................................................................6

Connecting the MS4UM to your computer..........................................................6

Formatting the HD.........................................................................................................7

Product Family.................................................................................................................8

Page 2

MS4UM Package Contents

System includes the following:

MS4UM...........................................................

Power Cord.....................................................

Manual & CD..................................................

HD Tray Keys.................................................

Removable Tray Modules(Screws Included).........

USB 2.0 Cable................................................

eSATA Cable ..................................................

2-Port eSATA PCIe Adapter Card...................

(Please contact us in case of missing or damaged items.)

Included

QUCIK INSTALLATION

MANUAL

Hardware Installation

MS4UM (FRONT) MS4UM (BACK)

HDD Access LED will flash purple when data is accesed from the hard drive only when HD is installed otherwise it will remain blue,

Power LED will light blue when the power is on.

Fail LED will light red when the internal temperature is higher than 60° C or when the fan fails.

NOTE:

3.5” Fan

eSATA Port

USB 2.0 Port

1.5”

HDD 1

HDD 2

HDD 3

HDD 4

Page 3

Step 5 Once the installation is completed, insert the tray back into the unit and firmly

push the handle to lock it in place (Fig.2).

Step 6 Connect all cables to the corresponding jacks. Then connect the power cord.

Step 7 Enclosure hardware installation is complete. You can power on the unit and

continue to Page 5 for the eSATA PCIe Card installation.

Installing a Hard Drive in the Removable Tray Module:

After verifying that the product body and related accessories are not missing or damaged,

please follow the steps below to install a hard drive in the removable tray module.

Step 1 Place the unit on a flat, stable surface. Make sure that the fan is not blocked and

there is appropriate space for heat dissipation. (Do not place the product near

water or any environment that may cause damage to the product).

Step 2 Press the key (included with this unit) into the lock hole located at the front of the

unit (Fig.1). Pull handle and remove tray (Fig.2).

Step 3 Unmount the plastic tray protector by removing the screws as illustrated (Fig.3).

Step 4 Fasten the Hard Drive with the screws (included with this unit) in the correspond

ing locations (Fig.4). Place the tray with the mounted HDD back into the case.

Fig.4

Fig.2

Fig.3

Fig.1

If you only need to install 1 to 3 hard disks, one hard disk must be inserted into HDD-1 location or the system will not work properly.

Page 4

NOTE:

Windows System Installation

Step 1

Step 4

Select “Manual Setup (Recommended

Selection)”, specify driver search from

CD-Rom.

Step 3

From your desktop, point the cursor

at “My Computer”, right click and

select “Manage”.

Select the driver and begin installation

process. After SATA card installation is

completed, the SATA card will be ready

for use.

Point the cursor to “Mass Storage

Controller” right click and select “Update

Driver”.

Step 2

For eSATA Port Multiplier Support

Installing the PCIe Adapter Card to

a Computer

For USB Connection Support

Please see Page 6 “Connecting the MS4UM to your computer.”

Fig.3

1. Insert the PCIe Card into an available PCIe slot

on your computer Fig.3.

2. Secure PCIe Card with screw.

PCI-Express Slots

PCI-E Card

Page 5

Sans Digital MobileStor MS4UM User manual

Sans Digital MobileStor MS4UM User manual

Sans Digital MobileStor MS4UM User manual

Related papers

Other documents