Sony STR-DN1080 Owner's manual

STR-DN1080

Multi Channel

AV Receiver

Operating Instructions

2

GB

For the customers in the USA

Owner’s Record

The model and serial numbers are located on

the rear of the receiver. Record the serial

number in the space provided below. Refer to

these numbers whenever you call upon your

Sony dealer regarding this product.

Model No. STR-DN1080

Serial No.

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation opening of the appliance with

newspapers, tablecloths, curtains, etc.

Do not expose the appliance to naked flame

sources (for example, lighted candles).

To reduce the risk of fire or electric shock, do not

expose this appliance to dripping or splashing,

and do not place objects filled with liquids, such

as vases, on the appliance.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the mains as

long as it is connected to the AC outlet, even if

the unit itself has been turned off.

CAUTION

Risk of explosion if the battery is replaced by an

incorrect type.

Do not expose batteries or appliances with

battery-installed to excessive heat, such as

sunshine and fire.

This symbol is intended to alert the

user to the presence of the Hot

Surface that may be hot if it is

touched during the normal

operation.

FOR UNITED STATES CUSTOMERS. NOT

APPLICABLE IN CANADA, INCLUDING IN

THE PROVINCE OF QUEBEC.

POUR LES CONSOMMATEURS AUX

ÉTATS-UNIS. NON APPLICABLE AU

CANADA, Y COMPRIS LA PROVINCE DE

QUÉBEC.

For the customers in the USA

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install

in accordance with the manufacturer’s

instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one wider

than the other. A grounding type plug has

two blades and a third grounding prong. The

wide blade or the third prong are provided

for your safety. If the provided plug does not

fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

11) Only use attachments/accessories specified

by the manufacturer.

WARNING

3

GB

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14) Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

NOTE:

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses and

can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the

equipment and receiver.

 Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

Properly shielded and grounded cables and

connectors must be used for connection to host

computers and/or peripherals in order to meet

FCC emission limits.

To reduce the risk of electric shock, the speaker

cable should be connected to the apparatus and

the speakers in accordance with the following

instructions.

1) Disconnect the AC power cord from the

MAINS.

2) Strip 10 to 15 mm of the wire insulation of the

speaker cable.

3) Connect the speaker cable to the apparatus

and the speakers carefully so as not to touch

the core of speaker cable by hand. Also

disconnect the AC power cord from the

MAINS before disconnecting the speaker

cable from the apparatus and the speakers.

This equipment must not be co-located or

operated in conjunction with any other antenna

or transmitter.

This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency

(RF) Exposure Guidelines. This equipment

should be installed and operated keeping the

radiator at least 20 cm or more away from

person's body (excluding extremities: hands,

wrists, feet and ankles).

5.47 GHz – 5.725 GHz band is restricted to indoor

operations only.

Compliance with FCC requirement 15.407(c)

Data transmission is always initiated by

software, which is the passed down through the

MAC, through the digital and analog baseband,

and finally to the RF chip. Several special packets

are initiated by the MAC. These are the only ways

the digital baseband portion will turn on the RF

transmitter, which it then turns off at the end of

the packet.

Therefore, the transmitter will be on only while

one of the aforementioned packets is being

transmitted. In other words, this device

automatically discontinue transmission in case

of either absence of information to transmit or

operational failure.

Frequency Tolerance: ±20 ppm

For the customers in Canada

Properly shielded and grounded cables and

connectors must be used for connection to host

computers and/or peripherals.

This device complies with Industry Canada’s

licence-exempt RSSs. Operation is subject to the

following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference,

including interference that may cause undesired

operation of the device.

4

GB

This equipment complies with IC radiation

exposure limits set forth for an uncontrolled

environment and meets RSS-102 of the IC radio

frequency (RF) Exposure rules. This equipment

should be installed and operated keeping the

radiator at least 20 cm or more away from

person's body (excluding extremities: hands,

wrists, feet and ankles).

5,150 MHz – 5,250 MHz band is restricted to

indoor operations only.

High-power radars are allocated as primary

users (i.e. priority users) of the bands

5,250 MHz – 5,350 MHz and 5,650 MHz –

5,850 MHz and that these radars could cause

interference and/or damage to LE-LAN devices.

For the customers in Australia and New

Zealand

This equipment should be installed and

operated with at least 20 cm and more between

the radiator and person’s body (excluding

extremities: hands, wrists, feet and ankles).

For the customers in Australia

Disposal of Old Electrical &

Electronic Equipment

(Applicable in the European

Union and other European

countries with separate

collection systems)

For the customers in Europe

Disposal of waste batteries

and electrical and electronic

equipment (applicable in the

European Union and other

European countries with

separate collection systems)

This symbol on the product, the battery or on the

packaging indicates that the product and the

battery shall not be treated as household waste.

On certain batteries this symbol might be used

in combination with a chemical symbol. The

chemical symbols for mercury (Hg) or lead (Pb)

are added if the battery contains more than

0.0005% mercury or 0.004% lead. By ensuring

these products and batteries are disposed of

correctly, you will help prevent potentially

negative consequences for the environment and

human health which could otherwise be caused

by inappropriate waste handling. The recycling

of the materials will help to conserve natural

resources.

In case of products that for safety, performance

or data integrity reasons require a permanent

connection with an incorporated battery, this

battery should be replaced by qualified service

staff only. To ensure that the battery and the

electrical and electronic equipment will be

treated properly, hand over these products at

end-of-life to the applicable collection point for

the recycling of electrical and electronic

equipment. For all other batteries, please view

the section on how to remove the battery from

the product safely. Hand the battery over to the

applicable collection point for the recycling of

waste batteries. For more detailed information

about recycling of this product or battery, please

contact your local Civic Office, your household

waste disposal service or the shop where you

purchased the product or battery.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying EU

directives

This product has been manufactured by or on

behalf of Sony Corporation, 1-7-1 Konan

Minato-ku Tokyo, 108-0075 Japan. Inquiries

related to product compliance based on

European Union legislation shall be addressed

to the authorized representative, Sony Belgium,

bijkantoor van Sony Europe Limited, Da

Vincilaan 7-D1, 1935 Zaventem, Belgium. For any

service or guarantee matters, please refer to the

addresses provided in the separate service or

guarantee documents.

5

GB

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive 2014/

53/EU.

The full text of the EU declaration of conformity

is available at the following internet address:

http://www.compliance.sony.de/

For this radio equipment, the following

restrictions on putting into service or of

requirements for authorization of use apply in

BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR, IT, CY,

LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, FI,

SE, UK, IS, LI, NO, CH, AL, BA, MK, MD, RS, ME, XK,

TR:

5,150 MHz – 5,350 MHz band is restricted to

indoor operations only.

This Multi Channel AV Receiver is intended for

sound and video playback from connected

devices, music streaming from an NFC-

compatible smartphone or a BLUETOOTH

device, and FM tuner. This system also supports

network streaming.

This equipment has been tested and found to

comply with the limits set out in the EMC

regulation using a connection cable shorter than

3 meters.

This radio equipment is intended to be used

with the approved version(s) of software that are

indicated in the EU Declaration of Conformity.

The software loaded on this radio equipment is

verified to comply with the essential

requirements of the Directive 2014/53/EU.

Software version: M__.R.____

You can display the software version

information. (System Information)

 Select [Setup] - [System Settings] from the home

menu.

 Select [System Information].

Excessive sound pressure from earphones and

headphones can cause hearing loss.

6

GB

Manuals provided for this product

The following manuals are provided for this product.

The information included in each manual is as shown below:

Preparation

Installation

Connections

Initial Setup

Basic operations

Listening/Watching

Advanced operations

Listening/Watching

Advanced operations

BLUETOOTH features

Network features

Multi-zone features

Other features

Adjusting Settings

Troubleshooting

Precautions / Specifications

Startup

Guide

Operating

Instructions

(this booklet)

Help Guide

(online)

For the customers in Europe

http://rd1.sony.net/help/ha/strdn108/h_eu/

For the customers in other areas

http://rd1.sony.net/help/ha/strdn108/h_zz/

To read the Help Guide, go to the following website:

7

GB

About These Operating

Instructions

These Operating Instructions mainly describe

the procedures for using the remote control.

You can also use the controls on the receiver if

they have the same or similar names as those

on the remote control.

Some illustrations are presented as conceptual

drawings, and may be different from the actual

products.

These Operating Instructions cover models for

the United States, Canada, Oceanian and

European countries.

Only the USA and Canadian models are

equipped with the SPEAKERS ZONE 2 terminals

on the rear of the receiver.

The USA and Canadian models are used for

illustrative purposes in these Operating

Instructions.

The items displayed on the TV screen may vary

depending on the area.

The text enclosed in bracket ([--]) appears on

the TV screen, and the text enclosed in double

quotation mark (“--”) appears on the display

panel.

Table of Contents

Manuals provided for this product ...............6

About These Operating Instructions ............ 7

Main features of the receiver .......................8

Supplied Accessories ................................... 11

Parts and Controls .......................................12

Preparation

Installing Speakers ......................................18

Connecting Speakers ..................................20

Connecting a TV .......................................... 29

Connecting Audio-Visual Devices .............. 33

Connecting to a network ............................ 38

Connecting the Antenna (aerial) ................39

Connecting the AC Power Cord

(mains lead) ........................................... 39

Setting up the Receiver using the Easy

Setup ......................................................40

Listening/Watching

Enjoying Sound and Video ......................... 42

Enjoying Sound Effects ...............................46

Network functions ......................................50

Listening with BLUETOOTH headphones/

speakers ..................................................51

Additional Information

Saving power .............................................. 53

Updating the Software ............................... 53

Troubleshooting ......................................... 54

Precautions .................................................58

Specifications ...............................................61

END USER LICENSE AGREEMENT ................66

8

GB

Main features of the receiver

Compatible with wired/wireless network, BLUETOOTH, and USB

connections

 Connect a Walkman, iPod/iPhone (AirPlay), computer, NAS, or USB device to the receiver to

play content on those devices or transmit music to BLUETOOTH headphones/speakers.

 Music services such as Spotify and Chromecast built-in are supported.

For details, see the Help Guide.

Compatible with the latest object-based audio formats

Dolby Atmos (page 24) and DTS:X are supported.

Compatible with high-definition playback of High- Resolution

Audio

 During network audio playback or content playback on a USB device, the receiver supports

High- Resolution Audio content at up to 5.6 MHz in the DSD format and at up to 192 kHz/24 bits

in the WAV, FLAC, and AIFF formats.

 Native playback of DSD files is also supported.

Compatible with high-definition 4K video formats*

 The receiver supports 4K HDR and HDCP 2.2, letting you enjoy high-definition video images

(page 33).

* You need to change the setting of [HDMI Signal Format] depending on the input video signal.

Automatically calibrating your viewing and listening environment

to create an ideal surround space using Auto Calibration (D.C.A.C.

EX*)

 D.C.A.C. EX measures and calibrates the distance, angle, level, and frequency characteristics of

the speakers using the supplied stereo calibration microphone (page 40).

 The optimum sound is then produced by simulating ideal speaker positions and angles

(Speaker Relocation**).

Calibration functions for sound fields corresponding to various

speaker installation conditions

 Phantom Surround Back**: Allows you to enjoy a surround-sound effect acoustically

equivalent to that of a 7-channel speaker system, using only a 5-channel speaker system, and

when using a 5.1.2-channel speaker system, it allows you to enjoy a surround-sound effect

acoustically equivalent to that of a 7.1.2-channel speaker system.

 Front Surround: Allows you to enjoy virtual surround sound with only two front speakers

(page 28).

Compatible with a variety of connections and high-quality audio/video

formats

Functions for an optimum surround environment

9

GB

 In-Ceiling Speaker Mode**: Reproduces more natural sound by lowering the position of audio

output from speakers installed in the ceiling.

 Center Speaker Lift Up**: Reproduces natural sound that feels more authentic by lifting the

sound from the center speaker up to the height of the screen.

* Digital Cinema Auto Calibration EX

** For details, see the Help Guide.

Sound fields selectable by preference

You can select from a variety of sound fields according to speaker connections or input sources

(2ch Stereo, Direct, Auto Format Decoding, etc.) (page 46).

Upscaling of existing sound sources into higher resolutions with

the same quantity of information as High-Resolution Audio using

DSEE HX (Digital Sound Enhancement Engine HX)*

The receiver restores signals in the micro region of compressed sound sources by up-sampling

the sampling frequency and expanding the bit depth to the equivalent of a maximum of 192 kHz/

24 bits, letting you enjoy CDs and lossy compressed sound sources such as MP3 files in expressive

sound quality closer to the original.

High-definition BLUETOOTH music playback (LDAC)*

LDAC allows approximately three times more data to be transmitted than with the previous

BLUETOOTH A2DP-SBC (328 kbps, 44.1 kHz). The receiver supports wireless playback

(transmission/reception) of high-quality sound when speakers, headphones, a Walkman, or a

smartphone that supports LDAC are connected to the receiver via a BLUETOOTH connection.

Reproduction of authentic impact and realistic sense of immersion

in movies (Sound Optimizer)*

Sound Optimizer calibrates the disparity in acoustic frequency characteristic between movie

production and playback caused by different volume levels, reproducing the impact and

immersive surround effect that the movie's sound engineers intended even when it is played

back at low volume levels in a home.

* For details, see the Help Guide.

Compatible with "SongPal"

1)

and "SongPal Link"

2)

SongPal is a dedicated app for operating SongPal compatible audio devices manufactured by

Sony from a smartphone or tablet device. It lets you operate the receiver from the smartphone

or tablet device and use the SongPal Link function.

Equipped with an HDMI jack compatible with eARC (Enhanced

Audio Return Channel) and ARC (Audio Return Channel)

TV sound can be output from the receiver using only one HDMI cable (page 31).

eARC is a new feature of HDMI Specification 2.1.

When you connect an eARC-compatible TV to the receiver, in addition to the audio formats

already supported by conventional ARC, you can also enjoy object-based audio formats such as

Dolby Atmos - Dolby TrueHD and DTS:X as well as Multi Channel Linear PCM, which cannot be

transmitted by ARC.

Audio technologies for high-definition music playback

Other useful functions

10

GB

Supports bi-amping of front speakers

You can enhance the sound quality of the front speakers by connecting different amplifiers to the

tweeter and woofer using a bi-amplifier connection (page 26).

Support for music and video playback in different rooms

2)

 The Wireless Multi-Room function

3)

lets you listen to the same music in different rooms.

 The multi-zone features let you output audio and video signals to another room.

1)

"SongPal" was redesigned as "Sony | Music Center." You can use "Sony | Music Center" on the receiver.

2)

For details, see the Help Guide.

3)

You can enjoy the sound of the device that is connected to the receiver. The sound is delayed behind the

picture.

11

GB

Supplied Accessories

 Remote control (1)

 R03 (size AAA) batteries (2)

 FM wire antenna (aerial) (1)

 Calibration microphone (1)

Insert two R03 (size AAA) batteries (supplied)

in the remote control. Make sure that the +

and – ends are in the correct position when

installing batteries.

Do not leave the remote control in an extremely

hot or humid place.

Do not use a new battery with old ones.

Do not mix manganese batteries and other kinds

of batteries.

Do not expose the remote control sensor to direct

sunlight or lights. Doing so may cause a

malfunction.

If you do not intend to use the remote control for

an extended period of time, remove the batteries

to avoid possible damage from battery leakage

and corrosion.

When the receiver no longer responds to the

remote control, replace both of the batteries with

new ones.

Inserting batteries into the

remote control

Note

12

GB

Parts and Controls

Front panel

 (power) (page 39)

 Power indicator

 SPEAKERS (page 41)

 CONNECTION PAIRING BLUETOOTH

Operates the BLUETOOTH function.

 TUNER PRESET +/–

Selects preset stations or channels.

 NFC sensor

 2CH/MULTI, MOVIE, MUSIC (page 46)

 Display panel (page 13)

 DISPLAY MODE

Switches information on the display panel.

 ZONE SELECT, ZONE POWER (page 43,

44)

 DIMMER

Adjusts the brightness of the display panel.

 Remote control sensor

Receives signals from remote control.

 PURE DIRECT

The indicator above the button lights up when

the Pure Direct function is activated.

 MASTER VOLUME (page 42)

 INPUT SELECTOR (page 42)

 (USB) port

Connect a USB device here.

 CALIBRATION MIC jack (page 41)

 PHONES jack

Connect headphones here.

Power indicator

 Green: The receiver is turned on.

 Amber: The receiver is in standby mode,

and you have set one of the following:

 [Control for HDMI], [Remote Start]*,

[Bluetooth Standby], or [Network

Standby]* is set to [On].

 [Standby Through] is set to [On] or [Auto].

 [Zone2 Power] or [HDMI Zone Power] is

set to [On].

 The indicator goes off: The receiver is in

standby mode and all of the following

settings are set to [Off]:

 [Control for HDMI]

 [Standby Through]

 [Remote Start]*

 [Bluetooth Standby]

 [Network Standby]*

 [Zone2 Power] and [HDMI Zone Power]

* For USA, Canadian and Oceanian models only.

Receiver

13

GB

Indicators on the display panel

 UPDATE

Lights up when new software is available.

 D.C.A.C.

Lights up when the measurement results of the

Auto Calibration (D.C.A.C. EX) function are

applied.

 S.OPT.

Lights up when the Sound Optimizer function is

activated.

 A.P.M.

Lights up when the A.P.M. (Automatic Phase

Matching) function is activated. You can only

set the A.P.M. function in the D.C.A.C. function.

 D.R.C.

Lights up when dynamic range compression is

activated.

 D.L.L.

Lights up when the D.L.L. (Digital Legato Linear)

function is activated.

 EQ

Lights up when the equalizer is activated.

 ZONE2, ZONE H

“ZONE2” lights up when the power for Zone 2 is

on.

“ZONE H” lights up when the power for HDMI

zone is on.

 ST

Lights up when the receiver tunes to a FM

stereo broadcast.

 HDMI OUT A + B

Indicates the HDMI OUT jacks that currently

output the audio/video signals.

 SLEEP

Lights up when the sleep timer is activated.

 Speaker system indicator (page 41)

 Neural:X

Lights up when DTS Neural:X decoding is

activated.

 Surr

Lights up when Dolby Surround decoding is

activated.

These indicators may not light up depending on

the speaker pattern setting.

 DSD Native

Lights up when DSD native playback function is

activated.

 IN-CEILING

Lights up when the In-Ceiling Speaker Mode is

activated.

 BLUETOOTH indicator

“BT” lights up when a BLUETOOTH device is

connected. Flashes while connecting.

“BT TX” lights up when an Audio-Visual device

connected to the receiver sends audio to the

BLUETOOTH headphones/speakers.

 Wireless LAN signal strength indicator

Show the strength of the wireless LAN signal.

No signal

Weak

Moderate

Strong

 Wired LAN indicator

Lights up when a LAN cable is connected.

 Input indicator

Lights up to indicate the current input.

HDMI

Digital signals are input through the selected

HDMI jack.

ARC

TV input is selected and eARC or ARC signals are

detected.

COAX

Digital signals are input through the COAXIAL

jack.

OPT

Digital signals are input through the OPTICAL

jack.

Note

14

GB

Rear panel

 COAXIAL IN jack

 HDMI IN/OUT jacks*

 IR REMOTE IN/OUT jacks

 You can control the receiver from a distance by

connecting an IR repeater (not supplied) to the

IR REMOTE IN jack.

 You can start or stop playback of devices such

as a CD player connected to the receiver by

connecting an IR blaster (not supplied) to the

IR REMOTE OUT jack.

 Wireless LAN antenna

 LAN port

 SPEAKERS terminals

Only the USA and Canadian models are

equipped with the SPEAKERS ZONE 2 terminals.

The USA and Canadian models are used for

illustrative purposes in these Operating

Instructions.

 ZONE 2 OUT jacks

 SUBWOOFER OUT jacks

 AUDIO IN jacks

 VIDEO IN/MONITOR OUT jacks

 FM ANTENNA terminal

 OPTICAL IN jack

* All of the HDMI IN/OUT jacks on the receiver

support HDCP 2.2. HDCP 2.2 is newly enhanced

copyright protection technology that is used to

protect content such as 4K movies.

15

GB

About input/output of video signals

The digital video signals input to the HDMI IN jacks of this receiver are output from HDMI OUT A

(TV) or HDMI OUT B/HDMI ZONE jacks only. The analog video signals input from VIDEO IN jacks

are output from the MONITOR OUT jack only.

Use the following illustration as reference when you connect the receiver, AV device, and TV.

When you connect the TV to the MONITOR OUT jack, the home menu of this receiver is not displayed on the TV

screen. To operate this receiver using the menu on the TV screen, connect the TV to the HDMI OUT A (TV) or

HDMI OUT B/HDMI ZONE jacks.

Note

HDMI OUT jack Any one of

the HDMI IN

HDMI OUT A (TV)

or HDMI OUT B/

HDMI ZONE

HDMI IN jack

Audio-Visual device The receiver TV

VIDEO OUT jack VIDEO IN MONITOR OUT VIDEO IN jack

16

GB

 (power)

Turns the receiver on or sets it to the standby

mode.

HDMI OUT

Switches the output for two TVs connected to

the HDMI OUT A (TV) and HDMI OUT B/HDMI

ZONE jacks.

When [HDMI Out B Mode] is set to [Main] in the

[HDMI Settings] menu, output is toggled

between “HDMI A”, “HDMI B”, “HDMI A+B” and

“HDMI OFF” each time the button is pressed.

When [HDMI Out B Mode] is set to [Zone],

output is toggled between “HDMI A” and “HDMI

OFF” each time the button is pressed.

Select “HDMI OFF” to turn off the output for the

HDMI OUT A (TV) and HDMI OUT B/HDMI ZONE

jacks.

 Input buttons

BD/DVD, SAT/CATV, GAME, SA-CD/CD,

USB, TV, FM

Selects the input channel connected to the

device you want to use. When you press any of

the input buttons, the receiver turns on.

WATCH, LISTEN

Allows you to display the Watch or Listen

screen directly without the need to select it on

the home menu.

Press WATCH to display the Watch screen or

LISTEN to display the Listen screen. Then press

either WATCH or LISTEN to select the input you

want to view.

 CUSTOM PRESET 1

Saves and recalls various settings for the

receiver. Press to select the custom preset

setting. Press and hold to save the current

settings to a preset.

MUSIC SERVICE

If you have listened to music streamed from

Spotify

1), 2)

on this receiver, press MUSIC

SERVICE to play the same music from exactly

the point it was left off.

For details on operation, visit the Help Guide.

BLUETOOTH RX/TX

Switches the [Bluetooth Mode] to [Receiver] or

[Transmitter].

In [Receiver] mode, the receiver receives and

outputs audio from the player.

In [Transmitter] mode, the receiver sends audio

to BLUETOOTH headphones/speakers.

FRONT SURROUND, 2CH/MULTI, MOVIE,

MUSIC

Selects a sound field.

DSD NATIVE

Activates the DSD Native function.

 DISPLAY

Displays information on the TV screen.

AMP MENU

Displays the menu on the display panel to

operate the receiver.

BACK

Returns to the previous menu or exits a menu

or on-screen guide that is displayed on the TV

screen.

OPTIONS

Displays the options menus.

(The menu is not displayed for the TV input.)

(enter), / / /

Press , , , to select the menu items.

Then, press

to enter the selection.

Remote control

17

GB

 HOME

Displays the home menu on the TV screen.

/ (previous/next),

 (play/pause)

3)

,  (stop)

Skip, play, pause, stop operation.

PRESET +/–

Selects preset stations or channels.

  (volume) +

3)

/–

Adjusts the volume level of all speakers at the

same time.

 (muting)

Turns off the sound temporarily. Press the

button again to restore the sound.

1)

Available services may vary depending on your

location.

2)

Spotify playback using the receiver is limited to

Spotify Premium accountholders.

3)

The  and  + buttons have tactile dots. Use

the tactile dots as reference when operating the

receiver.

The above explanation is intended to serve as

examples.

Depending on the model of your connected

device, some functions explained in this section

may not work with the supplied remote control.

Note

18

GB

Installing Speakers

You can connect up to 7 speakers and 2 subwoofers to this AV receiver. Place the speakers and

subwoofers according to the speaker system of your preference.

When you connect only one surround back speaker (SB), place the surround back speaker directly behind the

listening position.

As the subwoofer (SW) does not emit highly directional signals, you can place it wherever you want.

Preparation

Location of each speaker

Note

Names and functions of speakers

Abbreviations

used in

illustrations

Speaker name Functions

FL Front left speaker

Produces sounds from front left/right channels.

FR Front right speaker

CNT Center speaker Produces vocal sounds from center channel.

SL Surround left speaker

Produces sounds from surround left/right channels.

SR Surround right speaker

SBL

Surround back left

speaker

Produces sounds from surround back left/right channels.

SBR

Surround back right

speaker

SB Surround back speaker Produces sounds from surround back channel.

SW Subwoofer

Produces LFE (low frequency effect) channel sounds and

reinforces bass parts of other channels.

TML Top middle left speaker

Produces sounds from top middle left/right channels.

TMR Top middle right speaker

19

GB

Preparation

Select the speaker pattern according to the speaker configuration which you are using.

The table below shows examples of speaker configurations and speaker pattern settings. For

speaker placement and connection diagrams for each speaker configuration example, see

“Examples of speaker connections” (page 21).

* You can only set [Surround Back Speaker Assign] if the speaker pattern is set to a setting that does not have

surround back and height speakers.

The receiver allows you to enjoy a surround-sound effect acoustically equivalent to that of up to a 7.1.2-channel

speaker system when you select [Type A] or [Type B] for [SpeakerRelocation/PhantomSurroundBack] in the

[Speaker Settings] menu.

When setting [SpeakerRelocation/PhantomSurroundBack], perform Auto Calibration beforehand (page 40).

FDL

Front Dolby Atmos

enabled left speaker

Produces sounds from the top middle left/right channels

and reflects these sounds off the ceiling. Enables playing

back sounds of Dolby Atmos 3D movies without the need to

install ceiling speakers.

FDR

Front Dolby Atmos

enabled right speaker

SDL

Surround Dolby Atmos

enabled left speaker

Produces sounds from the top middle left/right channels

and reflects these sounds off the ceiling. Enables playing

back sounds of Dolby Atmos 3D movies without the need to

install ceiling speakers.

SDR

Surround Dolby Atmos

enabled right speaker

FHL Front high left speaker

Produces vertical sound effects from front height left/right

channels.

FHR Front high right speaker

Speaker configuration and speaker pattern settings

Speaker configuration in each zone [Surround Back

Speaker

Assign]*

[Speaker

Pattern] setting

For connection,

see page

Main zone Zone 2

5.1-channel Not used — [5.1] 21

7.1-channel using

surround back speakers

Not used — [7.1] 22

5.1.2-channel using top

middle speakers

Not used — [5.1.2 (TM)] 23

5.1.2-channel using Dolby

Atmos enabled speakers

Not used — [5.1.2 (FD)] 24

5.1-channel with Zone 2

speakers

2-channel [Zone2] [5.1] 25

5.1-channel with Bi-

Amplifier connection

Not used [BI-AMP] [5.1] 26

2.1-channel (for enjoying

Front Surround)

Not used — [2.1] 28

Abbreviations

used in

illustrations

Speaker name Functions

Tip

20

GB

Connecting Speakers

This receiver allows you to connect up to 7.1-channel system.

The speaker layout diagram is a guide for the ideal speaker placement. You do not need to adjust

your speaker placement exactly the same as the diagram.

Connect speakers with a nominal impedance of 6 ohms to 16 ohms.

Before connecting cables, be sure to disconnect the AC power cord (mains lead).

Before connecting the AC power cord (mains lead), make sure that metallic wires of the speaker cables are

not touching each other between the SPEAKERS terminals.

When you connect a subwoofer with an auto standby function, turn off the function when watching movies.

If the auto standby function is set to on, it turns to standby mode automatically based on the level of the input

signal to the subwoofer, and the sound may not be output.

If you have two subwoofers, you can connect them to both SUBWOOFER OUT jacks.

How to connect speaker cables

Be sure to connect the speaker cables correctly to the terminals of the speaker and this receiver.

Also, be sure to tightly twist the speaker wire strands and insert them securely into the speaker

terminals.

Be sure not remove too much of the speaker cable sleeves, so as to prevent the wires of the speaker cables

from touching each other.

Connect speaker cables properly with the polarities (+/–) matched between the receiver and the speakers.

Improper connection may result in fatal damage to the receiver.

Note

10mm

(13/32 in)

Page is loading ...

Sony STR-DN1080 Owner's manual

Sony STR-DN1080 Owner's manual

Related papers

Other documents