Sony STRDN1080 User manual

Category
Supplementary music equipment
Type
User manual
STR-DN1080
Multi Channel
AV Receiver
Operating Instructions
2
GB
For the customers in the USA
Owner’s Record
The model and serial numbers are located on
the rear of the receiver. Record the serial
number in the space provided below. Refer to
these numbers whenever you call upon your
Sony dealer regarding this product.
Model No. STR-DN1080
Serial No.
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the appliance with
newspapers, tablecloths, curtains, etc.
Do not expose the appliance to naked flame
sources (for example, lighted candles).
To reduce the risk of fire or electric shock, do not
expose this appliance to dripping or splashing,
and do not place objects filled with liquids, such
as vases, on the appliance.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Do not expose batteries or appliances with
battery-installed to excessive heat, such as
sunshine and fire.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main
plug from the AC outlet immediately.
The unit is not disconnected from the mains as
long as it is connected to the AC outlet, even if
the unit itself has been turned off.
This symbol is intended to alert the
user to the presence of the Hot
Surface that may be hot if it is
touched during the normal
operation.
FOR UNITED STATES CUSTOMERS. NOT
APPLICABLE IN CANADA, INCLUDING IN
THE PROVINCE OF QUEBEC.
POUR LES CONSOMMATEURS AUX
ÉTATS-UNIS. NON APPLICABLE AU
CANADA, Y COMPRIS LA PROVINCE DE
QUÉBEC.
For the customers in the USA
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one wider
than the other. A grounding type plug has
two blades and a third grounding prong. The
wide blade or the third prong are provided
for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11) Only use attachments/accessories specified
by the manufacturer.
WARNING
3
GB
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Properly shielded and grounded cables and
connectors must be used for connection to host
computers and/or peripherals in order to meet
FCC emission limits.
To reduce the risk of electric shock, the speaker
cable should be connected to the apparatus and
the speakers in accordance with the following
instructions.
1) Disconnect the AC power cord from the
MAINS.
2) Strip 10 to 15 mm of the wire insulation of the
speaker cable.
3) Connect the speaker cable to the apparatus
and the speakers carefully so as not to touch
the core of speaker cable by hand. Also
disconnect the AC power cord from the
MAINS before disconnecting the speaker
cable from the apparatus and the speakers.
This equipment must not be co-located or
operated in conjunction with any other antenna
or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines. This equipment
should be installed and operated keeping the
radiator at least 20 cm or more away from
person's body (excluding extremities: hands,
wrists, feet and ankles).
5.47 GHz – 5.725 GHz band is restricted to indoor
operations only.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by
software, which is the passed down through the
MAC, through the digital and analog baseband,
and finally to the RF chip. Several special packets
are initiated by the MAC. These are the only ways
the digital baseband portion will turn on the RF
transmitter, which it then turns off at the end of
the packet.
Therefore, the transmitter will be on only while
one of the aforementioned packets is being
transmitted. In other words, this device
automatically discontinue transmission in case
of either absence of information to transmit or
operational failure.
Frequency Tolerance: ±20 ppm
For the customers in Canada
Properly shielded and grounded cables and
connectors must be used for connection to host
computers and/or peripherals.
This device complies with Industry Canada’s
licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
4
GB
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment
should be installed and operated keeping the
radiator at least 20 cm or more away from
person's body (excluding extremities: hands,
wrists, feet and ankles).
5,150 MHz – 5,250 MHz band is restricted to
indoor operations only.
High-power radars are allocated as primary
users (i.e. priority users) of the bands
5,250 MHz – 5,350 MHz and 5,650 MHz
5,850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
For the customers in Australia and New
Zealand
This equipment should be installed and
operated with at least 20 cm and more between
the radiator and person’s body (excluding
extremities: hands, wrists, feet and ankles).
For the customers in Australia
Disposal of Old Electrical &
Electronic Equipment
(Applicable in the European
Union and other European
countries with separate
collection systems)
For the customers in Europe
Disposal of waste batteries
and electrical and electronic
equipment (applicable in the
European Union and other
European countries with
separate collection systems)
This symbol on the product, the battery or on the
packaging indicates that the product and the
battery shall not be treated as household waste.
On certain batteries this symbol might be used
in combination with a chemical symbol. The
chemical symbols for mercury (Hg) or lead (Pb)
are added if the battery contains more than
0.0005% mercury or 0.004% lead. By ensuring
these products and batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment and
human health which could otherwise be caused
by inappropriate waste handling. The recycling
of the materials will help to conserve natural
resources.
In case of products that for safety, performance
or data integrity reasons require a permanent
connection with an incorporated battery, this
battery should be replaced by qualified service
staff only. To ensure that the battery and the
electrical and electronic equipment will be
treated properly, hand over these products at
end-of-life to the applicable collection point for
the recycling of electrical and electronic
equipment. For all other batteries, please view
the section on how to remove the battery from
the product safely. Hand the battery over to the
applicable collection point for the recycling of
waste batteries. For more detailed information
about recycling of this product or battery, please
contact your local Civic Office, your household
waste disposal service or the shop where you
purchased the product or battery.
Notice for customers: the following
information is only applicable to
equipment sold in countries applying EU
directives
This product has been manufactured by or on
behalf of Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075 Japan. Inquiries
related to product compliance based on
European Union legislation shall be addressed
to the authorized representative, Sony Belgium,
bijkantoor van Sony Europe Limited, Da
Vincilaan 7-D1, 1935 Zaventem, Belgium. For any
service or guarantee matters, please refer to the
addresses provided in the separate service or
guarantee documents.
5
GB
Hereby, Sony Corp., declares that this
equipment is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
For details, please access the following URL:
http://www.compliance.sony.de/
This product is intended to be used in the
following countries.
AT, BE, BG, HR, CZ, DK, EE, FI, FR, DE, GR, HU, IS,
IE, IT, LV, LT, LU, NL, NO, PL, PT, RO, SK, SI, ES, SE,
CH, GB, BA, MK, RS, TR, CY, LI, MT, AL, MD, ME,
Kosovo
5,150 MHz – 5,350 MHz band is restricted to
indoor operations only.
This Multi Channel AV Receiver is intended for
sound and video playback from connected
devices, music streaming from an NFC-
compatible smartphone or a BLUETOOTH
device, and FM tuner. This system also supports
network streaming.
This equipment has been tested and found to
comply with the limits set out in the EMC
regulation using a connection cable shorter than
3 meters.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6
GB
Manuals provided for this product
The following manuals are provided for this product.
The information included in each manual is as shown below:
Preparation
Installation
Connections
Initial Setup
Basic operations
Listening/Watching
Advanced operations
Listening/Watching
Advanced operations
BLUETOOTH features
Network features
Multi-zone features
Other features
Adjusting Settings
Troubleshooting
Precautions / Specifications
Startup
Guide
Operating
Instructions
(this booklet)
Help Guide
(online)
For the customers in Europe
http://rd1.sony.net/help/ha/strdn108/h_eu/
For the customers in other areas
http://rd1.sony.net/help/ha/strdn108/h_zz/
To read the Help Guide, go to the following website:
7
GB
About These Operating
Instructions
These Operating Instructions mainly describe
the procedures for using the remote control.
You can also use the controls on the receiver if
they have the same or similar names as those
on the remote control.
Some illustrations are presented as conceptual
drawings, and may be different from the actual
products.
These Operating Instructions cover models for
the United States, Canada, Oceanian and
European countries.
Only the USA and Canadian models are
equipped with the SPEAKERS ZONE 2 terminals
on the rear of the receiver.
The USA and Canadian models are used for
illustrative purposes in these Operating
Instructions.
The items displayed on the TV screen may vary
depending on the area.
The text enclosed in bracket ([--]) appears on
the TV screen, and the text enclosed in double
quotation mark (“--”) appears on the display
panel.
Table of Contents
Manuals provided for this product ...............6
About These Operating Instructions ............ 7
Main features of the receiver .......................8
Supplied Accessories ................................... 11
Parts and Controls .......................................12
Preparation
Installing Speakers ......................................18
Connecting Speakers ..................................20
Connecting a TV .......................................... 29
Connecting Audio-Visual Devices .............. 33
Connecting to a network ............................ 38
Connecting the Antenna (aerial) ................39
Connecting the AC Power Cord
(mains lead) ........................................... 39
Setting up the Receiver using the Easy
Setup ......................................................40
Listening/Watching
Enjoying Sound and Video ......................... 42
Enjoying Sound Effects ...............................46
Network functions ......................................50
Listening with BLUETOOTH headphones/
speakers ..................................................51
Additional Information
Saving power .............................................. 53
Updating the Software ............................... 53
Troubleshooting ......................................... 54
Precautions .................................................58
Specifications ...............................................61
END USER LICENSE AGREEMENT ................66
8
GB
Main features of the receiver
Compatible with wired/wireless network, BLUETOOTH, and USB
connections
Connect a Walkman, iPod/iPhone (AirPlay), computer, NAS, or USB device to the receiver to
play content on those devices or transmit music to BLUETOOTH headphones/speakers.
Music services such as Spotify and Chromecast built-in are supported.
For details, see the Help Guide.
Compatible with the latest object-based audio formats
Dolby Atmos (page 24) and DTS:X are supported.
Compatible with high-definition playback of High- Resolution
Audio
During network audio playback or content playback on a USB device, the receiver supports
High- Resolution Audio content at up to 5.6 MHz in the DSD format and at up to 192 kHz/24 bits
in the WAV, FLAC, and AIFF formats.
Native playback of DSD files is also supported.
Compatible with high-definition 4K video formats*
The receiver supports 4K HDR and HDCP 2.2, letting you enjoy high-definition video images
(page 33).
* You need to change the setting of [HDMI Signal Format] depending on the input video signal.
Automatically calibrating your viewing and listening environment
to create an ideal surround space using Auto Calibration (D.C.A.C.
EX*)
D.C.A.C. EX measures and calibrates the distance, angle, level, and frequency characteristics of
the speakers using the supplied stereo calibration microphone (page 40).
The optimum sound is then produced by simulating ideal speaker positions and angles
(Speaker Relocation**).
Calibration functions for sound fields corresponding to various
speaker installation conditions
Phantom Surround Back**: Allows you to enjoy a surround-sound effect acoustically
equivalent to that of a 7-channel speaker system, using only a 5-channel speaker system, and
when using a 5.1.2-channel speaker system, it allows you to enjoy a surround-sound effect
acoustically equivalent to that of a 7.1.2-channel speaker system.
Front Surround: Allows you to enjoy virtual surround sound with only two front speakers
(page 28).
Compatible with a variety of connections and high-quality audio/video
formats
Functions for an optimum surround environment
9
GB
In-Ceiling Speaker Mode**: Reproduces more natural sound by lowering the position of audio
output from speakers installed in the ceiling.
Center Speaker Lift Up**: Reproduces natural sound that feels more authentic by lifting the
sound from the center speaker up to the height of the screen.
* Digital Cinema Auto Calibration EX
** For details, see the Help Guide.
Sound fields selectable by preference
You can select from a variety of sound fields according to speaker connections or input sources
(2ch Stereo, Direct, Auto Format Decoding, etc.) (page 46).
Upscaling of existing sound sources into higher resolutions with
the same quantity of information as High-Resolution Audio using
DSEE HX (Digital Sound Enhancement Engine HX)*
The receiver restores signals in the micro region of compressed sound sources by up-sampling
the sampling frequency and expanding the bit depth to the equivalent of a maximum of 192 kHz/
24 bits, letting you enjoy CDs and lossy compressed sound sources such as MP3 files in expressive
sound quality closer to the original.
High-definition BLUETOOTH music playback (LDAC)*
LDAC allows approximately three times more data to be transmitted than with the previous
BLUETOOTH A2DP-SBC (328 kbps, 44.1 kHz). The receiver supports wireless playback
(transmission/reception) of high-quality sound when speakers, headphones, a Walkman, or a
smartphone that supports LDAC are connected to the receiver via a BLUETOOTH connection.
Reproduction of authentic impact and realistic sense of immersion
in movies (Sound Optimizer)*
Sound Optimizer calibrates the disparity in acoustic frequency characteristic between movie
production and playback caused by different volume levels, reproducing the impact and
immersive surround effect that the movie's sound engineers intended even when it is played
back at low volume levels in a home.
* For details, see the Help Guide.
Compatible with "SongPal" and "SongPal Link"*
SongPal is a dedicated app for operating SongPal compatible audio devices manufactured by
Sony from a smartphone or tablet device. It lets you operate the receiver from the smartphone
or tablet device and use the SongPal Link function.
Equipped with an ARC-compatible HDMI jack
TV sound can be output from the receiver using only one HDMI cable (page 31).
Audio technologies for high-definition music playback
Other useful functions
10
GB
Supports bi-amping of front speakers
You can enhance the sound quality of the front speakers by connecting different amplifiers to the
tweeter and woofer using a bi-amplifier connection (page 26).
Support for music and video playback in different rooms
The Wireless Multi-Room function** lets you listen to the same music in different rooms.
The multi-zone features let you output audio and video signals to another room.
* For details, see the Help Guide.
** You can enjoy the sound of the device that is connected to the receiver. The sound is delayed behind the
picture.
11
GB
Supplied Accessories
Remote control (1)
R03 (size AAA) batteries (2)
FM wire antenna (aerial) (1)
Calibration microphone (1)
Insert two R03 (size AAA) batteries (supplied)
in the remote control. Make sure that the +
and – ends are in the correct position when
installing batteries.
Do not leave the remote control in an extremely
hot or humid place.
Do not use a new battery with old ones.
Do not mix manganese batteries and other kinds
of batteries.
Do not expose the remote control sensor to direct
sunlight or lights. Doing so may cause a
malfunction.
If you do not intend to use the remote control for
an extended period of time, remove the batteries
to avoid possible damage from battery leakage
and corrosion.
When the receiver no longer responds to the
remote control, replace both of the batteries with
new ones.
Inserting batteries into the
remote control
Note
12
GB
Parts and Controls
Front panel
 (power) (page 39)
Power indicator
SPEAKERS (page 41)
CONNECTION PAIRING BLUETOOTH
Operates the BLUETOOTH function.
TUNER PRESET +/–
Selects preset stations or channels.
NFC sensor
2CH/MULTI, MOVIE, MUSIC (page 46)
Display panel (page 13)
DISPLAY MODE
Switches information on the display panel.
ZONE SELECT, ZONE POWER (page 43,
44)
DIMMER
Adjusts the brightness of the display panel.
Remote control sensor
Receives signals from remote control.
PURE DIRECT
The indicator above the button lights up when
the Pure Direct function is activated.
MASTER VOLUME (page 42)
INPUT SELECTOR (page 42)
 (USB) port
Connect a USB device here.
CALIBRATION MIC jack (page 41)
PHONES jack
Connect headphones here.
Power indicator
Green: The receiver is turned on.
Amber: The receiver is in standby mode,
and you have set one of the following:
[Control for HDMI], [Remote Start]*,
[Bluetooth Standby], or [Network
Standby]* is set to [On].
[Standby Through] is set to [On] or [Auto].
[Zone2 Power] or [HDMI Zone Power] is
set to [On].
The indicator goes off: The receiver is in
standby mode and all of the following
settings are set to [Off]:
[Control for HDMI]
[Standby Through]
[Remote Start]*
[Bluetooth Standby]
[Network Standby]*
[Zone2 Power] and [HDMI Zone Power]
* For USA, Canadian and Oceanian models only.
Receiver
13
GB
Indicators on the display panel
UPDATE
Lights up when new software is available.
D.C.A.C.
Lights up when the measurement results of the
Auto Calibration (D.C.A.C. EX) function are
applied.
S.OPT.
Lights up when the Sound Optimizer function is
activated.
A.P.M.
Lights up when the A.P.M. (Automatic Phase
Matching) function is activated. You can only
set the A.P.M. function in the D.C.A.C. function.
D.R.C.
Lights up when dynamic range compression is
activated.
D.L.L.
Lights up when the D.L.L. (Digital Legato Linear)
function is activated.
EQ
Lights up when the equalizer is activated.
ZONE2, ZONE H
“ZONE2” lights up when the power for Zone 2 is
on.
“ZONE H” lights up when the power for HDMI
zone is on.
ST
Lights up when the receiver tunes to a FM
stereo broadcast.
HDMI OUT A + B
Indicates the HDMI OUT jacks that currently
output the audio/video signals.
SLEEP
Lights up when the sleep timer is activated.
Speaker system indicator (page 41)
Neural:X
Lights up when DTS Neural:X decoding is
activated.
Surr
Lights up when Dolby Surround decoding is
activated.
These indicators may not light up depending on
the speaker pattern setting.
DSD Native
Lights up when DSD native playback function is
activated.
IN-CEILING
Lights up when the In-Ceiling Speaker Mode is
activated.
BLUETOOTH indicator
“BT” lights up when a BLUETOOTH device is
connected. Flashes while connecting.
“BT TX” lights up when an Audio-Visual device
connected to the receiver sends audio to the
BLUETOOTH headphones/speakers.
Wireless LAN signal strength indicator
Show the strength of the wireless LAN signal.
No signal
Weak
Moderate
Strong
Wired LAN indicator
Lights up when a LAN cable is connected.
Input indicator
Lights up to indicate the current input.
HDMI
Digital signals are input through the selected
HDMI jack.
ARC
TV input is selected and Audio Return Channel
(ARC) signals are detected.
COAX
Digital signals are input through the COAXIAL
jack.
OPT
Digital signals are input through the OPTICAL
jack.
Note
14
GB
Rear panel
COAXIAL IN jack
HDMI IN/OUT jacks*
IR REMOTE IN/OUT jacks
You can control the receiver from a distance by
connecting an IR repeater (not supplied) to the
IR REMOTE IN jack.
You can start or stop playback of devices such
as a CD player connected to the receiver by
connecting an IR blaster (not supplied) to the
IR REMOTE OUT jack.
Wireless LAN antenna
LAN port
SPEAKERS terminals
Only the USA and Canadian models are
equipped with the SPEAKERS ZONE 2 terminals.
The USA and Canadian models are used for
illustrative purposes in these Operating
Instructions.
ZONE 2 OUT jacks
SUBWOOFER OUT jacks
AUDIO IN jacks
VIDEO IN/MONITOR OUT jacks
FM ANTENNA terminal
OPTICAL IN jack
* All of the HDMI IN/OUT jacks on the receiver
support HDCP 2.2. HDCP 2.2 is newly enhanced
copyright protection technology that is used to
protect content such as 4K movies.
15
GB
About input/output of video signals
The digital video signals input to the HDMI IN jacks of this receiver are output from HDMI OUT A
(TV) or HDMI OUT B/HDMI ZONE jacks only. The analog video signals input from VIDEO IN jacks
are output from the MONITOR OUT jack only.
Use the following illustration as reference when you connect the receiver, AV device, and TV.
When you connect the TV to the MONITOR OUT jack, the home menu of this receiver is not displayed on the TV
screen. To operate this receiver using the menu on the TV screen, connect the TV to the HDMI OUT A (TV) or
HDMI OUT B/HDMI ZONE jacks.
Note
HDMI OUT jack Any one of
the HDMI IN
HDMI OUT A (TV)
or HDMI OUT B/
HDMI ZONE
HDMI IN jack
Audio-Visual device The receiver TV
VIDEO OUT jack VIDEO IN MONITOR OUT VIDEO IN jack
16
GB
 (power)
Turns the receiver on or sets it to the standby
mode.
HDMI OUT
Switches the output for two TVs connected to
the HDMI OUT A (TV) and HDMI OUT B/HDMI
ZONE jacks.
When [HDMI Out B Mode] is set to [Main] in the
[HDMI Settings] menu, output is toggled
between “HDMI A”, “HDMI B”, “HDMI A+B” and
“HDMI OFF” each time the button is pressed.
When [HDMI Out B Mode] is set to [Zone],
output is toggled between “HDMI A” and “HDMI
OFF” each time the button is pressed.
Select “HDMI OFF” to turn off the output for the
HDMI OUT A (TV) and HDMI OUT B/HDMI ZONE
jacks.
Input buttons
BD/DVD, SAT/CATV, GAME, SA-CD/CD,
USB, TV, FM
Selects the input channel connected to the
device you want to use. When you press any of
the input buttons, the receiver turns on.
WATCH, LISTEN
Allows you to display the Watch or Listen
screen directly without the need to select it on
the home menu.
Press WATCH to display the Watch screen or
LISTEN to display the Listen screen. Then press
either WATCH or LISTEN to select the input you
want to view.
CUSTOM PRESET 1
Saves and recalls various settings for the
receiver. Press to select the custom preset
setting. Press and hold to save the current
settings to a preset.
MUSIC SERVICE
If you have listened to music streamed from
Spotify
1), 2)
on this receiver, press MUSIC
SERVICE to play the same music from exactly
the point it was left off.
For details on operation, visit the Help Guide.
BLUETOOTH RX/TX
Switches the [Bluetooth Mode] to [Receiver] or
[Transmitter].
In [Receiver] mode, the receiver receives and
outputs audio from the player.
In [Transmitter] mode, the receiver sends audio
to BLUETOOTH headphones/speakers.
FRONT SURROUND, 2CH/MULTI, MOVIE,
MUSIC
Selects a sound field.
DSD NATIVE
Activates the DSD Native function.
DISPLAY
Displays information on the TV screen.
AMP MENU
Displays the menu on the display panel to
operate the receiver.
BACK
Returns to the previous menu or exits a menu
or on-screen guide that is displayed on the TV
screen.
OPTIONS
Displays the options menus.
(enter), / / /
Press , , , to select the menu items.
Then, press
to enter the selection.
Remote control
17
GB
HOME
Displays the home menu on the TV screen.
/ (previous/next),
(play/pause)
3)
, (stop)
Skip, play, pause, stop operation.
PRESET +/–
Selects preset stations or channels.
(volume) +
3)
/–
Adjusts the volume level of all speakers at the
same time.
(muting)
Turns off the sound temporarily. Press the
button again to restore the sound.
1)
Available services may vary depending on your
location.
2)
Spotify playback using the receiver is limited to
Spotify Premium accountholders.
3)
The and + buttons have tactile dots. Use
the tactile dots as reference when operating the
receiver.
The above explanation is intended to serve as
examples.
Depending on the model of your connected
device, some functions explained in this section
may not work with the supplied remote control.
Note
18
GB
Installing Speakers
You can connect up to 7 speakers and 2 subwoofers to this AV receiver. Place the speakers and
subwoofers according to the speaker system of your preference.
When you connect only one surround back speaker (SB), place the surround back speaker directly behind the
listening position.
As the subwoofer (SW) does not emit highly directional signals, you can place it wherever you want.
Preparation
Location of each speaker
Note
Names and functions of speakers
Abbreviations
used in
illustrations
Speaker name Functions
FL Front left speaker
Produces sounds from front left/right channels.
FR Front right speaker
CNT Center speaker Produces vocal sounds from center channel.
SL Surround left speaker
Produces sounds from surround left/right channels.
SR Surround right speaker
SBL
Surround back left
speaker
Produces sounds from surround back left/right channels.
SBR
Surround back right
speaker
SB Surround back speaker Produces sounds from surround back channel.
SW Subwoofer
Produces LFE (low frequency effect) channel sounds and
reinforces bass parts of other channels.
TML Top middle left speaker
Produces sounds from top middle left/right channels.
TMR Top middle right speaker
19
GB
Preparation
Select the speaker pattern according to the speaker configuration which you are using.
The table below shows examples of speaker configurations and speaker pattern settings. For
speaker placement and connection diagrams for each speaker configuration example, see
“Examples of speaker connections” (page 21).
* You can only set [Surround Back Speaker Assign] if the speaker pattern is set to a setting that does not have
surround back and height speakers.
The receiver allows you to enjoy a surround-sound effect acoustically equivalent to that of up to a 7.1.2-channel
speaker system when you select [Type A] or [Type B] for [SpeakerRelocation/PhantomSurroundBack] in the
[Speaker Settings] menu.
When setting [SpeakerRelocation/PhantomSurroundBack], perform Auto Calibration beforehand (page 40).
FDL
Front Dolby Atmos
enabled left speaker
Produces sounds from the top middle left/right channels
and reflects these sounds off the ceiling. Enables playing
back sounds of Dolby Atmos 3D movies without the need to
install ceiling speakers.
FDR
Front Dolby Atmos
enabled right speaker
SDL
Surround Dolby Atmos
enabled left speaker
Produces sounds from the top middle left/right channels
and reflects these sounds off the ceiling. Enables playing
back sounds of Dolby Atmos 3D movies without the need to
install ceiling speakers.
SDR
Surround Dolby Atmos
enabled right speaker
FHL Front high left speaker
Produces vertical sound effects from front height left/right
channels.
FHR Front high right speaker
Speaker configuration and speaker pattern settings
Speaker configuration in each zone [Surround Back
Speaker
Assign]*
[Speaker
Pattern] setting
For connection,
see page
Main zone Zone 2
5.1-channel Not used [5.1] 21
7.1-channel using
surround back speakers
Not used [7.1] 22
5.1.2-channel using top
middle speakers
Not used [5.1.2 (TM)] 23
5.1.2-channel using Dolby
Atmos enabled speakers
Not used [5.1.2 (FD)] 24
5.1-channel with Zone 2
speakers
2-channel [Zone2] [5.1] 25
5.1-channel with Bi-
Amplifier connection
Not used [BI-AMP] [5.1] 26
2.1-channel (for enjoying
Front Surround)
Not used [2.1] 28
Abbreviations
used in
illustrations
Speaker name Functions
Tip
20
GB
Connecting Speakers
This receiver allows you to connect up to 7.1-channel system.
The speaker layout diagram is a guide for the ideal speaker placement. You do not need to adjust
your speaker placement exactly the same as the diagram.
Before connecting cables, be sure to disconnect the AC power cord (mains lead).
Before connecting the AC power cord (mains lead), make sure that metallic wires of the speaker cables are
not touching each other between the SPEAKERS terminals.
When you connect a subwoofer with an auto standby function, turn off the function when watching movies.
If the auto standby function is set to on, it turns to standby mode automatically based on the level of the input
signal to the subwoofer, and the sound may not be output.
If you have two subwoofers, you can connect them to both SUBWOOFER OUT jacks.
How to connect speaker cables
Be sure to connect the speaker cables correctly to the terminals of the speaker and this receiver.
Also, be sure to tightly twist the speaker wire strands and insert them securely into the speaker
terminals.
Be sure not remove too much of the speaker cable sleeves, so as to prevent the wires of the speaker cables
from touching each other.
Connect speaker cables properly with the polarities (+/–) matched between the receiver and the speakers.
Improper connection may result in fatal damage to the receiver.
Note
Note
10mm
(13/32 in)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Sony STRDN1080 User manual

Category
Supplementary music equipment
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI