Legrand Qbasic Upgradeable Roller Shades Manual User guide

Brand: Legrand

Model: Qbasic Upgradeable Roller Shades Manual

Type: User guide

Legrand Qbasic Upgradeable Roller Shades Manual provide a convenient and stylish way to control the amount of light entering a room. With their manual operation, these shades are easy to use and can be adjusted to any desired height. The shades are available in a variety of colors and fabrics to match any décor, and they can be installed inside or outside the window frame.

Here are some of the features and benefits of Legrand Qbasic Upgradeable Roller Shades Manual:

Manual operation for easy adjustment
Available in a variety of colors and fabrics to match any décor
Can be installed inside or outside the window frame

Here are some of the features and benefits of Legrand Qbasic Upgradeable Roller Shades Manual:

Manual operation for easy adjustment
Available in a variety of colors and fabrics to match any décor
Can be installed inside or outside the window frame

Solarfective

Manual upgradeable shades

Installation Instructions

No: SF-QBInst – 07/18 rev. 1

Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: SF-QBP

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

INSTALL THE MOUNTING BRACKETS

If the clutch is on the right end of the shade, attach the brackets to the window frame, window molding, wall or ceiling, as shown below.

If the clutch is on the left end of the shade, reverse the bracket positions, left for right.

1. The brackets are configured for mounting based on the original order.

However, if a change is needed, you can adjust the spring bracket.

• Adjusting the Spring Bracket – Remove the three phillips head screws

which attach the inner mount to the outer bracket. If changing from back or

side mount to top mount, rotate the outer bracket so that the bracket holes

are at the top, the stop is to the back and the opening for the plug slot is at

the front. Reattach the inner mount to the outer bracket.

NOTE: The clutch bracket does not need to be adjusted.

2. Mark the spots in the wall or window sill where the screws will be located. Drill

a pilot hole with a 1/8” drill bit.

3. Using a hex driving bit, install the screws as shown below. Make sure that the

brackets are level.

Clutch Bracket

Spring Bracket

Screws

Inner Mount

Outer Bracket

Back or Side Mount

Configuration

Top Mount

Configuration

Stop

Opening for

Plug Slot

Rotating the Plug Bracket for Top Mounting

Clutch Bracket

Spring Bracket

Spring

Bracket

Clutch

Bracket

Back Mount Side Mount Top Mount

INSTALLING THE SHADE

1. With the shade still wrapped in plastic but with the ends exposed, insert the tab on the

clutch bracket into the clutch, then swing the plug end into the slot, so that it rests at the

bottom of the slot.

2. Remove plastic covering.

Spring

Shaft

Rests

Here

Spring

Shaft

OPERATING THE SHADE

Pulling gently on the chain in one direction raises the shade; pulling it in the other direction lowers it.

On shades where the fabric rolls against the window, the front chain does the raising. On shades where the fabric rolls toward the room,

the rear chain does the raising.

INSTALLING THE CHILD SAFETY DEVICE

The Child Safety Device reduces the hazards of strangulation and entanglement of young children by limiting

access to the control chain. Anchor the Child Safety Device, which is attached to the shade’s control chain, to the

window frame or wall, so that young children cannot pull the cord around their necks.

1. Lower the shade.

2. Hold the child safety device upright as shown in the diagram.

3. Position the child safety device on the window frame or the wall so that the child safety device and control

chain do not interfere with raising or lowering the shade. The child safety device should be installed

without stretching or pulling down on the control chain. Stretching the chain will cause excessive

wear. Do not twist or cross the control chain. If using stop balls,position the tension device 1/4 inch higher

to allow the stop ball to pass through the tension device.

4. Holding the child safety device upright, and in position, as shown, insert and secure the screws through the

holes. The mounting screws must be secured into a solid surface or molly.

ATTACHING A STOP TO THE CONTROL CHAIN

The stop on the plug bracket prevents the shade from being rolled up too far. But a stop should also

be attached the control chain to prevent the shade from lowering too far. A stop bead is included with

the chain for this purpose.

1. Lower the shade to the lowest desired point at the sill or floor.

2. Place the stop bead over the bead closest to the clutch on the side furthest away from the

shade. On a standard roll shade this will be the chain in front. On a reverse roll shade, it will be

the chain in the back.

3. With a pliers, gently squeeze the stop so that it cannot be removed.

Stop Bead

Shade

ADJUSTING THE SHADE HEIGHT

If needed, the shade can

be leveled by adjusting the

height of the slot on the spring

bracket. This can help prevent

telescoping of the roll as the

shade is raised. It is also useful

for adjusting shade height of

two shades placed next to each

other so they are plumb with

each other

Using a 2mm hex wrench, turn

the vertical jack screw to raise

or lower the inner mount of the

spring bracket.

SHIMMING THE SHADE

A slight amount of telescoping is normal, But if a large amount

of telescoping still occurs when the shade is rolled up, even

after leveling the shade by adjusting the spring bracket, try

shimming the shade.

With the shade rolled all the

way down, place a piece of

tape on the side of the roll

that the fabric is telescoping

away from.

The shade will always track

towards the side where the

tape is placed

Direction of

Telescoping

Tape

800.879.8585

www.legrand.us/solarfective

No. SF-QBInst – 07/18 rev. 1

LIMITED WARRANTY

Manufacturer warrants that this window shade product, and/or specific components of the window shade product, will be free from defects in materials

and workmanship for the period of time specified herein. Beginning from the date first sold to the commercial or residential consumer (either, the “Buyer”)

who has, or intends to, use the product, as evidenced by such Buyer’s proof of purchase, this Limited Warranty, as applicable to the specified product or

component, as such product or component is defined by Manufacturer, will be in effect for the time periods set forth below:

• For all motorized products, controls and electronic accessories: 5 (five) years

• For all manual products and controls: 5 (five) years

• For fabrics used in shades, if procured and supplied by Manufacturer as part of a roller shade: 5 (five) years

Exclusions From this Limited Warranty: This Limited Warranty shall be null and void and no part of it shall apply if any one of the followingoccur: 1) the

product has not been properly installed by a qualified installer in accordance with all Manufacturer specifications; 2) theproduct has been subject to

unauthorized service; 3) the product has been subject to mishandling, misuse, or abuse; 4) the product has been modified;5) the product has suffered

damage resulting from lightning, power surges, vandalism, fire, earthquake, acts of nature, or any other cause which the product was not designed to

withstand; 6) the product has been used, or attempted to be used, for other than the customary usage or for other than the product’s intended use; 7) the

product has not been maintained in accordance with Manufacturer’s instructions; 8) damage to the product caused by battery decay or corrosion.

This Limited Warranty extends only to the original owner and is only valid if the product or component is purchased either directly from Manufacturer or

an authorized reseller. This Limited Warranty is not transferable. This Limited Warranty does not cover normal wear or tear or deterioration which occurs

with the passage of time.

Batteries originally provided with a new product, if any, are produced by a third party and are not warranted by Manufacturer. No employee, distributor,

dealer, agent or representative is authorized to change the terms of this Limited Warranty in any way, to extend the warranty time periods, or to grant

additional warranties, and no attempt to do any of the foregoing will be binding upon Manufacturer.

IF THIS LIMITED WARRANTY COVERS A CONSUMER PRODUCT, AS DEFINED BY THE MAGNUSON-MOSS WARRANTY ACT AND APPLICABLE

CANADIAN CONSUMER PROTECTION LAWS, THEN NO WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, BUT NOT LIMITED TO, THE

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) SHALL EXTEND BEYOND THE APPLICABLE TIME PERIOD

STATED IN BOLD FACE TYPE ABOVE. IF THIS LIMITED WARRANTY COVERS A COMMERCIAL PRODUCT, THEN THIS LIMITED WARRANTY

IS IN LIEU OF ALL OTHER REPRESENTATIONS, GUARANTEES, OR OTHER EXPRESS OR IMPLIED WARRANTIES (INCLUDING, WITHOUT

LIMITATION, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND ALL SUCH OTHER EXPRESSED OR

IMPLIED WARRANTIES ARE HEREBY SPECIFICALLY DISCLAIMED.

Claims for defects in material and workmanship covered by this Limited Warranty must be made in writing to the dealer from whom the product was

originally first purchased within the warranty period stated above. Manufacturer may either send a service representative or have the product returned

to Manufacturer’s facility, at Buyer’s expense, for inspection. If judged by Manufacturer to be defective in material or workmanship, and to otherwise be

covered by this Limited Warranty, the product will be replaced or repaired at the option of Manufacturer, in its sole and absolute discretion, free from

all charges except authorized transportation and replacement labor. Replacement labor, transportation costs, and any other costs or charges by the

dealer, wholesaler, distributor, contractor, or installer are not covered by this Limited Warranty. Any replacement unit may be a model determined by

Manufacturer to be equivalent to the defective model, or a product that has been factory refurbished. The remainder of original warranty period will apply

to any repair/replacement unit.

THE REMEDIES OF BUYER SET FORTH IN THIS LIMITED WARRANTY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES. THE

LIABILITY OF MANUFACTURER WHETHER IN CONTRACT, TORT, UNDER ANY WARRANTY OR OTHERWISE, SHALL NOT EXTEND BEYOND

ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART FOUND BY MANUFACTURER TO BE DEFECTIVE IN

MATERIAL OR WORKMANSHIP AND OTHERWISE SUBJECT TO THIS LIMITED WARRANTY. MANUFACTURER SHALL NOT BE RESPONSIBLE

FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

This Limited Warranty gives specific legal rights and Buyer may have other rights, which may vary from jurisdiction to jurisdiction. However, some

jurisdictions do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the

above limitations or exclusions may not apply to specific Buyers.

For Warranty Service, contact us at:

Solarfective

55 Hymus Rd

Scarborough, ON M1L 2C6, Canada