Robertshaw 4510 Series Low Temperature Control Kit User manual

Brand: Robertshaw

Model: 4510 Series Low Temperature Control Kit

Type: User manual

INSTALLATION DATA

VC4510

low temperature CoNtrol KIt

Description

The Robertshaw® Low Temperature Model BJFMA without switch and

BJFMAZ with pressure switch for “Oven On” and “Oven Ready” panel

light applicaons. Control has outlet ngs for 1/4” pipe, 3/8” and

7/16” tubing. Pilot outlet extension ng is 3/16” tubing. Stem length

adaptor, chrome bezel, ange nipple “O” ring gasket and 4-way dial are

included in the kit.

cAUtion

THIS DEVICE SHOULD BE INSTALLED BY A QUALIFIED SERVICE

TECHNICIAN WITH DUE REGARD FOR SAFETY AS IMPROPER

INSTALLATION COULD RESULT IN A HAZARDOUS CONDITION.

rotAtion oF reAr HoUsinG

If rear housing on the replacement control is in the desired posion,

proceed to controL MoUntinG secon.

To rotate housing posion, proceed as follows:

1. Gas cock must be turned to the “OFF’” posion.

2. Remove four hex head bolts on rear of control and comptetely

separate housings. Do not turn valve or valve stem while control

is disassembled.

3. Using a small screwdriver, push in the calibraon screw in the

center of the gas cock plug. Turn this screw 1/4 turn in either

direcon. This will allow the sloed end of the gas cock to engage

the valve stem cross pins when the control is ressembled.

NOTE: If the above procedure is followed carefully, calibraon will not

be aected when the rear housing is reassembled.

4. Reassemble rear housing with outlet down. Be certain cross pin on

end of valve stem engages slot in inner end of gas cock.

Do not Force toGetHer. When properly aligned, rear housing

will move into posion easily.

5. Replace and ghten the four hex head bolts.

controL MoUntinG

NOTE: DIASTAT IS LIQUID FILLED AND SHARP BENDS ARE TO BE

AVOIDED. Recommended method to uncoil diastat is to insert a round

screwdriver sha through the center of the diastat coil and push away

from the control body.

1. Assemble outlet ngs required into control.

2. Mount control using new manifold gasket and mounng bolts.

3. Aach pilot line.

4. Connect outlet line.

5. Turn on gas supply and leak test all connecons.

DiAL steM AsseMBLY

lnsert “D” stem dial sleeve into front of control and snap in place.

When addional stem length is required, use stem length adaptor as

follows:

1. Place adaptor on “D” stem dial sleeve and place dial on adaptor.

2. To determine correct adaptor length, measure distance from back

edge of dial to panel front or bezel. Cut this amount o small end

of adaptor.

3. If ghter dial t is desired, spread end of “D” stem sleeve and stem

length adaptor slightly.

BeZeL instALLAtion

Bezel and sleeve are installed by closing center sleeve over dial guide

on the front of the control.

If standard sleeve is too short, remove from bezel. Use pliers to apply

light pressure and squeeze the adaptor slightly to disengage locking

tabs. Install correct length sleeve in bezel.

Bezel index posion can be changed to match manifold mounng

posion of control. Snap sleeve out of bezel as described above.

sWitcH terMinAL connections

“Oven on” terminals are located on the inner side of the switch next to

the control body. “Oven ready” terminals are located on the outer side

of the switch. Terminal connecons required for replacing each specic

model control are shown in the following chart.

oLD MoDeL Use terMinALs

BJFMX OVEN READY

BJFMZ ALL

BJFMAX OVEN READY

BJFMAY OVEN ON

BJFMAZ ALL

operAtinG instrUctions

HeAter piLot ADJUstMent

1. Be sure constant burning pilot is ignited.

2. Turn heater pilot adjusng key counterclockwise to full open.

3. Turn dial to the DOT posion (between “OFF” and “140°”), then

turn heater pilot adjusng key clockwise unl ame extends about

1/2” beyond bulb on type #50 pilot or 1/4” beyond bulb on

type #52 pilot.

BY-PASS ADJ.

HEATER PILOT

ADJ.

DIAL

SLEEVE

BEZEL

DIAL

ADAPTOR

OUTLET

FITTING

V4510-001

(BJFMA)

SWITCH LEFT

OUTLET RIGHT

SWITCH RIGHT

OUTLET LEFT

STEM LENGTH

Customer Service Telephone 1.800.304.6563

Customer Service Facsimile 1.800.426.0804

[email protected]

Robertshaw®, Ranco®, Paragon® and Uni-Line® are

trademarks of Robertshaw, its subsidiaries and/or

affiliated companies. All other brands mentioned

may be the trademarks of their respective owners.

For Technical Service

Telephone 1.800.445.8299

Facsimile 1.630.260.7294

[email protected]

www.uni-line.com

www.robertshaw.com

10/14 –1-116 Rev B

BY-pAss ADJUstMent

1. Be sure constant burning pilot is ignited.

2. Turn by-pass adjusng key counterclockwise to full open.

3. Turn dial to “Broil.”

4. Aer ve minutes, turn dial to the DOT posion between “O” and

“140°” and adjust ame with by-pass adjusng key so that it will

just hold on the oven burner.

serVice instrUctions

to recALiBrAte controL

The minimum ame (by-pass) on the oven burner must be properly

adjusted before checking oven temperature or recalibrang. To check

oven temperature, use a test Instrument or a reliable mercury ther-

mometer. Temperature should be checked in the center of the oven.

Calibraon Check Procedure:

1. Set dial at 400°F mark and light oven burner.

2. Aer burner has been on about 15 minutes, check oven

temperature. If recalibraon is required, proceed as directed.

3. Remove dial assembly and “D” type stem.

4. With a screwdriver, push calibraon stem inward and while holding

stem rmly in, using the screwdriver bit as a reference point, turn

stem clockwise to obtain a lower temperature or counterclockwise

for a higher temperature. Each mark on retainer represents 25

degrees. Replace dial assembly and “D” type stem with dial.

5. To check your calibraon seng, open door and allow oven to cool.

Repeat steps 1, 2 and 3. Recalibrate, if necessary, following steps 4

and 5.

Robertshaw 4510 Series Low Temperature Control Kit User manual

Robertshaw 4510 Series Low Temperature Control Kit User manual

Robertshaw 4510 Series Low Temperature Control Kit User manual

Related papers

Other documents