Toro Chute Gate Kit, GrandStand Mower Installation guide

Toro
Brand
Toro
Model
Chute Gate Kit, GrandStand Mower
Type
Installation guide
FormNo.3403-305RevB
ChuteGateKit
GrandStand
®
Mower
ModelNo.133-1434
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential
danger.Replaceanydecalthatisdamagedorlost.
117-8569
1.Operatordischargecontrol3.Closed
2.Open4.ReadtheOperator's
Manual.
©2016—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3403-305*B
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Removetheexistingside-discharge
chute.
Side-dischargechute
1
Bolt(5/16x7-1/2inch)
1
Locknut(5/16inch)
1
Spacer
1
2
Spring
1
Installtheside-dischargechute.
Handleassembly1
Bolt(3/8x1inch)
2
3
Nut(3/8inch)
2
Installthehandle.
4
Cabletie
3Routethecables.
5
Trashbag1Installthetrashbag.
1
RemovingtheExisting
Side-DischargeChute
NoPartsRequired
Procedure
1.Shutofftheengine,waitforallmovingpartstostop,
engagetheparkingbrake,andremovethekey.
2.Removethelocknut,bolt,spring,andspacerholding
thegrassdeectortothepivotbrackets(Figure1).
Removethegrassdeector.
Figure1
1.Bolt
4.Spring
2.Grassdeector
5.Locknut
3.Spacer
2
2
InstallingtheSide-Discharge
Chute
Partsneededforthisprocedure:
1
Side-dischargechute
1
Bolt(5/16x7-1/2inch)
1
Locknut(5/16inch)
1
Spacer
1
Spring
Procedure
WARNING
Anuncovereddischargeopeningcouldallowthe
machinetothrowobjectsatyouorbystandersand
resultinseriousinjury.Also,contactwiththeblade
couldoccur.
•Neveroperatethemachineunlessyouinstalla
coverplate,amulchplate,oragrasschuteand
catcher.
•Makesurethatthegrassdeectorisinthedown
position.
1.Alignthedischarge-chutebracketwithdeckbracket
andplacethenewspacerandspringontothegrass
deector(Figure2).
Note:InstalltheL-endofthespringbehindthedeck
edge.
Figure2
1.Bolt
4.Spring
2.Grassdeector
5.Locknut
3.Spacer6.Springinstalled
2.Installtheboltandnut.PlacetheJ-hookendofthe
springaroundthegrassdeector(Figure2).
3.Tightenthenutuntiltheendoftheboltisushwith
theendofthenut.
Note:Donotovertighten.
Important:Thegrassdeectormustbeableto
lowerdownintoposition.Liftthedeectorupto
testthatitlowersintothefulldownposition.
3
InstallingtheHandle
Partsneededforthisprocedure:
1Handleassembly
2
Bolt(3/8x1inch)
2
Nut(3/8inch)
Procedure
1.Releasethecushionandremovethefueltank;referto
theOperator’sManualforthemachine.
2.Usea3/8inchdrillbittodrillopenthe2holesonthe
leftsideofthemachineshowninFigure3.
Figure3
3
3.Installthehandleassemblytothemachineusing2
boltsand2nutsasshowninFigure4.
Figure4
1.Handleassembly3.Nut
2.Bolt
4.Installthefueltankandsecurethecushion;refertothe
Operator’sManualforthemachine.
4
RoutingtheCables
Partsneededforthisprocedure:
3
Cabletie
Procedure
1.Routethecablesacrossthemachine,infrontofthe
fueltank(Figure5).
Figure5
Enginenotshown
1.Fueltank
2.Cable
2.Routethecablesthroughtheengineplateandacross
themowerdeckasshowninFigure6.
Figure6
Enginenotshownincalloutbubble
1.Engineplate2.Mowerdeck
4
3.Removethenutsfromthecables.
4.Threadthecablesthroughthereardischarge-chute
bracket(Figure7).
Note:Routethecablethatisontheleftsideofthe
handleassemblythroughtheleftsideofthebracket;
routetheothercablethroughtherightside.
Figure7
1.Discharge-chutebrackets2.Pulley
5.Install1nutoneachcable.
6.Threadthecablesthroughthefrontbracketandinstall
theothernutsontothecable(Figure8).
Figure8
1.Nut
3.Slotsinpulley
2.Thecablesarenotloose.
7.Slidetheendsofthecablesintotheslotsinthepulley
(Figure8).
8.Adjustthenutsonthecablessothatthecablesarenot
loosebetweenthebracketandpulley(Figure8).
9.Ensurethatthechutedoorisparalleltothedeckand
thatthemowerbladedoesnotcontactitwhenyou
movethechute-controlhandletotheClosedposition;
adjustthecablesasnecessary.
10.Usethecabletiestosecurethecablestothefanguard
andawayfrommovingparts(Figure9).
Figure9
Enginenotshownincalloutbubble
1.Cabletie
5
InstallingtheTrashBag
Partsneededforthisprocedure:
1Trashbag
Procedure
Installthetrashbagintotheslotsinthehandleassembly
(Figure10).
Figure10
1.Trashbag
2.Slotsinhandleassembly
5
Operation
UsingtheChuteGate
CAUTION
Thechutegatedoesnotsealthedischarge
opening.Grassandobjectsmaybethrowntoward
bystanders,resultinginseriousinjury.
•Beawareofthemowerdischargedirectionand
donotpointitatanyone.
•Removeobstaclessuchasrocks,treelimbs,etc.
fromthemowingarea.
•Neverputyourhandsorfeetunderthemower
ordischargearea.
•Nevertrytoclearthedischargeareaormower
bladesunlesstheengineisoffandyouremove
thekey.
Usethechutegatetotemporarilystopordeectgrass
clippingsawayfromsidewalks,parkinglots,patios,or
anywhereyoudonotwantgrassclippingstoland.Thechute
gatehas3positions:open,45degreeangle,andclosed.
•Rotatethechutegatehandletotheopenpositiontoallow
grassclippingstodischarge(Figure11).
•Rotatethechutegatehandletothe45degreeangleto
deectthegrassclippings(Figure11).
•Rotatethechutegatehandletotheclosedpositionto
stopthegrassclippings(Figure11).
Figure11
1.Chutegateopen3.Chutegateclosed
2.Chutegateat45degree
angle
6
Notes:
7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Toro Chute Gate Kit, GrandStand Mower Installation guide

Toro
Brand
Toro
Model
Chute Gate Kit, GrandStand Mower
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents