Extron DA HD 4K Series User manual

Category
Video line amplifiers
Type
User manual
1
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
DA4 HD 4K and DA 6 HD 4K• Setup Guide
Overview
The Extron DA4 HD 4K and DA6 HD 4K distribution ampliers
distribute one HDMIinput signal to four or six outputs
simultaneously (following the HDMI 1.4 specication at
resolutions up to UHD and 4K). This setup guide provides basic
instructions for installation by an experienced installer. For
complete instructions, see the DA HD 4K Series User Guide at
www.extron.com.
Front Panel
DA4 HD 4K
HDMI DISTRIBUTION AMPLIFIER
CONFIG
HDCP
1234
SIGNAL
INPUT OUTPUTS
DA6 HD 4K
HDMI DISTRIBUTION AMPLIFIER
CONFIG
HDCP
1234
SIGNAL
INPUT OUTPUTS
56
CCDD
CC
D
D
FF
FF
EE
EE
BBAA
A
Power status LED — Lights green when power is applied to the unit.
B
USB Config port — Used for SIS™ conguration, monitoring, and rmware updates.
C
Input Signal LED — Lights green when a TMDS signal is detected on the HDMI input.
D
Output Signal LEDs — Light green when HPD is detected from the corresponding sink device and when a TMDS
signal is detected at the input.
E
Input HDCP LED — Lights green when the source requires HDCP encryption and it has been authenticated with the
HDMI input.
F
Output HDCP LEDs — Light green when HDCP is authenticated between the DA4 HD 4K or DA6 HD 4K output and
the corresponding sink device.
Rear Panel
5
0
/
60 Hz
100
-24
0
V ~
0
.
3
A MAX
D
A4 HD 4K
RS
-232
T
x
R
x
G
REM
T
OU
TP
U
T
S
INPUT
50/60 Hz
100-240V ~ 0.3A MAX
DA4 HD 4K
RS-232
4321
Tx Rx G
REMOTEOUTPUTSINPUT
50
/
60 H
z
100
-24
0
V ~
0
.
3
A MAX
DA6
HD
4
K
RS
-232
T
x
Rx
G
O
UTPUT
S
EM
TE
INPUT
50/60 Hz
100-240V ~ 0.3A MAX
DA6 HD 4K
RS-232
4
36
521
Tx Rx G
OUTPUTS REMOTEINPUT
CCAA BB DD
50/60
Hz
100-240V ~ 0.3A MAX
DA4 HD 4K
RS-232
4321
Tx Rx G
REMOTEOUTPUTSINPUT
1
3
1
4
2
3
1
4
2
3
1
4
2
2
3
1
0
0
L
I
N
K
A
C
T
C
OM
I
R
IN
P
U
T
RE
L
AY
T
X
RX
R
IPL
2
50
®
O
N
O
F
F
D
I
S
PLA
Y
MU
T
E
S
C
R
E
E
N
U
P
S
C
R
E
E
N
D
O
WN
V
C
R
D
V
D
D
O
C
C
AM
L
A
P
T
O
P
PC
MOD
E
L
80
MOD
E
L
80
MOD
E
L
80
MOD
E
L
80
Extron
DA4 HD 4K
Distribution
Amplier
HDMI
Cables
RS-232
TCP/IP
TouchLink
Control
System
4K Displays
4K Media Player
A
Power input — Connect the provided female IEC cable
to a 100‑240VAC (50or 60 Hz) power source.
B
HDMI input — Connect a source device to this female
HDMI type A connector.
C
HDMI outputs — Connect up to four or six display
devices to these female HDMI type A connectors.
D
RS-232 — Used for SIS conguration, monitoring, and
rmware updates (Pin 1 = Tx, Pin 2 = Rx, Pin 3 = Ground).
Protocol: 9600 baud, 8 data bits, 1 stop bit, no parity.
2
68-2636-51 A
03 16
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA ‑ West Extron USA ‑ East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. www.extron.com
DA4 HD 4K and DA6 HD 4K • Setup Guide (Continued)
Installation
1. Mount the DA4 HD 4K or DA6 HD 4K in a suitable location (see www.extron.com for mounting options). Follow the
instructions provided with the mounting kit.
2. If required, connect a control PC to the USB Cong port (Front Panel
B
on the previous page) or RS‑232 connector
(Rear Panel
D
on the previous page). To connect the rear panel RS‑232 connector to a PC, ensure that the PC
transmit connects to the RS‑232 receive and the PC receive connects to the RS‑232 transmit (see the diagram below).
RS-232
Tx Rx G
REMOTE
TransmitReceive
ReceiveTransmit
GroundGround
DB9 Pin Locations
Female
51
96
Pin 2 = Rx
Pin 3 = Tx
Pin 5 = G
Computer DA HD 4K
NOTE: Use PCS or SIS commands to congure EDID Minder
®
, mute the video signal, mute the audio signal, adjust
the video color bit depth, or monitor the signal and HDCP status. See the “PCS Software” or “SIS Commands”
sections of the DA HD 4K Series User Guide.
3. Connect the display devices to the rear panel HDMI outputs and power them on. Connect the primary display to
output 1. EDID from output 1 is stored automatically.
NOTE: Use the LockIt
®
HDMI cable lacing brackets provided to secure the HDMI connectors.
Follow these instructions to secure the input and output HDMI connectors to the unit with the LockIt HDMI lacing
bracket provided:
a. Plug the HDMI cable into the rear panel connection (
1
).
b. Loosen the HDMI connection mounting screw from the rear panel enough to
allow the LockIt lacing bracket to be placed over it (
2
). The screw does not
have to be removed.
c. Place the LockIt lacing bracket on the screw and against the HDMI
connector, then tighten the screw to secure the bracket (
3
).
ATTENTION:
Do not overtighten the HDMI connection mounting screw. The
shield it fastens to is very thin and can easily be stripped.
Ne serrez pas trop la vis de montage du connecteur HDMI. Le
blindage auquel elle est attachée est très n et peut facilement
être dénudé.
d. Loosely place the included tie wrap around the HDMI connector and the
LockIt lacing bracket as shown (
4
).
e. While holding the connector securely against the lacing bracket, tighten the
tie wrap, then remove any excess length.
4. Connect the provided female IEC cable to the female IECconnector to a 100‑240VAC (50or 60 Hz) power source.
5. Connect and power on the source device.
3
11
2
2
3
3
4
4
  • Page 1 1
  • Page 2 2

Extron DA HD 4K Series User manual

Category
Video line amplifiers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI