OSP Home Furnishings BP-BAR4-NA Operating instructions

Brand
OSP Home Furnishings
Model
BP-BAR4-NA
Type
Operating instructions
IF PARTS ARE MISSING OR DAMAGED, DO NOT RETURN TO STORE
To order missing or replacement parts, contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
Item# BP-BARCSL4
BARCELONA 4 DOOR CONSOLE
ASSEMBLY INSTRUCTIONS
LIMITED WARRANTY
INSPIRED by Bassett
®
Warrants, to the original purchaser its products to be free from defects in material and workmanship for a period of
5 years. Defects and damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event
beyond the control of INSPIRED by Bassett
®
is not covered. The warranty does not cover cosmetic damage that may result from normal
use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To make a warranty claim, contact Customer Service, provide model number, sales receipt and description of the problem. It is the
customer’s responsibility to prepay freight on any components returned to the factory. INSPIRED by Bassett
®
will pay return freight on
components covered under terms of warranty.
WARNING
1. Do not use this product unless all screws and bolts are securely tightened.
2. Check that all screws and bolts are tight every three months or as needed.
3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
6. Intended for residential use only.
Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
November, 2017
PARTS LIST
(2) Bottom Frame (1 PC)
(1) Top Frame (1 PC)
(4) Right Side Frame (1 PC)
(3) Left Side Frame (1 PC)
(6) Left Back Panel (1 PC)
(5) Divider (1 PC)
(8) Left Door (2 PCS)
(7) Right Back Panel (1 PC)
(10) Shelf (2 PCS)
(9) Right Door (2 PCS)
HARDWARE LIST
DRAWINGNO DESCRIPTION SIZE
A
B
C
D
E
F
G
H
I
J
K
L
M
QTY.
12 PCS
1/4” x 1/2” 2 PCS
2 PCS
Small Bolt
1/4” x 2/5”Connector Bolt
1/8” x 1” 4 PCSLarge Screw
Medium Flat Washer
Large Flat Washer
1/4” x 2/5” x 0.08”Lock Washer
8 PCS1/4” x 2/5”Nut
8 PCSn / aShelf Pin
4 PCSn / aHandle
2/5” x 4/5” x 0.08” 2 PCS
12 PCS1/4” x 5/8” x 0.08”
1/4” x 2” 8 PCSLong Bolt
1/4” x 9/5” 4 PCSMedium Bolt
1/8” x 5/8” 16 PCSSmall Screw
8 PCS1/4” x 1/2” x 0.08”Small Flat Washer
HARDWARE LIST
DRAWINGNO DESCRIPTION SIZE
N
O
P
Q
R
S
QTY.
n / a 2 PCS
2 PCS
Back Lid
n / a 1 PCCenter Leg
2/5” 1 PCSocket Wrench
n / a 1 PCTriangle
1/5”Allen Wrench
1 PCn / aAnti-Tip Kit
THANK YOU for purchasing this quality product. Be sure to check all packing material carefully for small parts which may have come
loose inside the carton during shipment. Identify and count all parts and compare with the parts and hardware lists.
Phillips Screwdriver also needed for assembly (not provided).
STEP 1:
STEP 2:
(1)
(5)
(2)
(6 & 7)
(Q)
(Q)
(A)
(D)
(I)
(O)
(H)
(J)
(B)
(Q)
Attach Top Frame (1) and Bottom Frame (2) to Divider (5) using two Long Bolts (B), two Lock Washers (J) and two Flat
Washers (H) for each frame. FULLY TIGHTEN ALL BOLTS.
Attach Back Lid (O) to Back Panels (6 & 7) using one Small Bolt (A), one Flat Washer (I) and one Connector Bolt (D).
FULLY TIGHTEN ALL BOLTS.
STEP 3:
STEP 4:
(6)
(7)
(6)
(7)
(1)
(2)
(F)
(E)
(2)
(4)
(H)
(J)
(C)
(Q)
Slide Back Panels (6 & 7) into groove of Top Frame (1) and Bottom Frame (2).
Secure Left Side Frame (3) and Right Side Frame (4) to console using four Long Bolts (C), four Lock Washers (J) and four
Flat Washers (H). FULLY TIGHTEN ALL BOLTS. Secure Back Panels (6 & 7) to assembled console using two Large Screws (F)
and four Small Screws (E) for each panel. DO NOT FULLY TIGHTEN SCREWS.
STEP 5:
STEP 6:
(6)
(7)
(2)
(P)
(S)
(4)
(G)
(K)
(R)
(G)
(K)
(R)
(8)
(9)
(M)
Line up Back Panels (6 & 7) using Triangle (Q) and tighten Screws (F & E). Screw in Center Leg (P) into assembled console.
FULLY TIGHTEN ALL SCREWS.
Attach Handles (M) to Doors (8 & 9) using two Flat Washers (G) and two Nuts (K) for each handle. FULLY TIGHTEN ALL NUTS.
STEP 7:
STEP 8:
(1)
(5)
(4)
(3)
(8)
(10)
(8)
(9)
(10)
(L)
(9)
(1)
(5)
(4)
(3)
Attach Doors (8 & 9) to assembled console.
Insert Shelf Pins (L) into assembled console. Slide Shelves (10) into assembled console.
STEP 9:
(6)
(N)
(7)
(4)
(1)
Place Console (1) in desired location. Attach two brackets to back of Console (1) using two short screws for each bracket.
FULLY TIGHTEN SCREWS. Attach the remaining brackets to wall using two long screws for each bracket. FULLY TIGHTEN SCREWS.
Loop one safety strap between each set of brackets and fasten safety straps.
FURNITURE CARE:
- Dust with a soft cloth following the grain pattern of the wood.
- Dust often to remove the everyday abrasive particles from the wood surfaces.
- Before dusting, moisten cloth lightly with a spray product.
- Wood finishes also benefit from an occasional polishing.
Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through
Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

OSP Home Furnishings BP-BAR4-NA Operating instructions

Brand
OSP Home Furnishings
Model
BP-BAR4-NA
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents