Noble House 305126 Operating instructions

Brand
Noble House
Model
305126
Type
Operating instructions

This manual is also suitable for

Page 1 of 6Page 1 of 6
Caution : You must read this before you proceed
TABLE
CAUTION: This Table is NOT a TOY.
Keep your child / children at bay during the assembly
process.
For moving the Table and to prevent damage to the Table,
For moving the Table and to prevent damage to the Table,
two adults are needed to execute this action.
Noble House Home Furnishings LLC
Page 2 of 6
Label Picture Description QTY
A Table Top 1
B Leg 4
C Leg Support 4
Label Picture Description QTY
Bolt (M6x50mm) 9
1
Bolt (M6x50mm) 9
3 Washer 9
4 Allen Key 1
Before Beginning Assembly:
1
2
3
4
Noble House Home Furnishings LLC
Screw (M6x35mm) 9
Page 3 of 6
OVERVIEW
FRONT FACING
Leg (B)
Table Top (A)
Leg Support (C)
Step 1
This Table has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Table parts, the above picture is to help you
put the various parts into perspective. Please read through the instructions
below to familiarise yourself with the parts and steps before assembly.
Unpack and place all parts on a clean, non-marring surface.
Noble House Home Furnishings LLC
Page 4 of 6
Step 2
Attach Leg(B) to the Table Top(A) using Bolt(
①
) and Washer(
③
) with Allen
Key(
④
).
Do not fully tighten Bolts
A
B
1
4
3
Step 3
① ③
④
Do not fully tighten Bolts
Repeat the same process with the remaining three Legs(B)
Place Leg Support(C) between Table Top(A) and Leg(B), as shown above.
3.1) Secure Leg Support(C) to Table Top(A) using Screw(
②
) with Allen
Key(
④
)
3.2) Secure Leg Support(C) to Leg(B) using Screw(
②
) with Allen Key(
④
)
Do not fully tighten Screws
C
B
A
4
2
Step 3.1
Step 3.2
2
4
Repeat the same process with the remaining three Leg Supports(C).
Noble House Home Furnishings LLC
Page 5 of 6
Step 4
Turn the Table over, with assistance from your partner.
EXERT pressure, floorwards, onto the Table.
This pressure will help the Legs and Table Top reach alignment at all joints.
Check for wobbles.
In a sequential manner, gradually tighten all Bolts and Screws until evenly
secured.
Step 5
Inspect Table and make sure all parts are adequately connected.
secured.
When tightening the Bolts and Screws tighten sequentially.
Do not tighten any Bolt or Screw fully and then move towards the next one.
This could cause the frame to warp.
If there are still wobbles, loosen the Bolts and Screws and execute the
same above process.
If the Table is not Stable it could lead to damage to the product.
Inspect Table and make sure all parts are adequately connected.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
Page 6 of 6
OUTDOOR
Noble House Home Furnishings LLC
Label Picture Description QTY
A Left Armrest / Leg 1
B Right Armrest / Leg 1
C Seat 1
D Seat Back 1
Caution: You must read this before you proceed
Single Chair
Label Picture Description QTY
E Allen Key 1
F
Bolt
(
M6*30mm
)
5
G
Bolt
(M6*40mm)
3
H
Bolt
(M6*60mm)
3
I Washer 13
J Seat Cushion 1
K
Bolt
(
M6*20mm
)
2
L Connection 1
M Connection 1
Before Beginning Assembly:
Step 1
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting
positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting positions.
Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)
as shown in the picture above.
Loosely tighten the Bolts.
Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 4
Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 3
Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as
shown in the picture above.
Loosely tighten the Bolts.
Place the Seat Cushion(J) on the Chair.
Your Chair is ready for use.
Step 5
Check for stability and then tighten all Bolts at all joints.
Note: DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly
secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Noble House 305126 Operating instructions

Brand
Noble House
Model
305126
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents