Page 1 / 4 PW-RC08
HDPE ROCKING ADIRONDACK CHAIR
Read all assembly and care instructions carefully before using this product. Save this manual for future reference.
ABackrest 1
BSeat 1
CRight Armrest 1
DLeft Armrest 1
E1 Front Right Leg 1
E2 Front Left Leg 1
F1 Back Right Leg 1
F2 Back Left Leg 1
GLeg Support 2
HRocker Runner 2
ICenter Seat Support 1
JRear Seat Support 1
KM4x40mm Screw 8
LM6x50mm Bolt Set 18
MM6x50mm Bolt 4
NM6x80mm Bolt Set 2
OM6x90mm Bolt Set 2
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
customerservice@sunnydazedecor.com, or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
CHOKING HAZARD — This item contains small
parts that can be swallowed. Keep children and pets
away during assembly.
WARNING
(not included)
Phillips Screwdriver
10mm Wrench
HELPFUL HINT
Do not fully tighten hardware until all components are
assembled. If hardware is tightened too soon, mounting
holes may not align, and parts may not easily t together.
2-PERSON
ASSEMBLY
RECOMMENDED
01/2022
ASSEMBLY
STEP 1
B: 1
I: 1
J: 1
K: 2
STEP 2
K: 6
STEP 3
C: 1
D: 1
E1: 1
E2: 1
F1: 1
F2: 1
L: 4
STEP 4
H: 2
L: 8
NOTE:
Do not fully tighten hardware until Step 5 is complete.
Page 2 / 4 PW-RC08
Review all steps and understand assembly before beginning.
Do not fully tighten hardware until all components have been loosely assembled.
• Align the mounting holes of Center Seat Support (I)
with Rear Seat Support (J) and securely fasten them
using two M4x40mm Screws (K).
• Place the assembled supports in the bottom of Seat
(B), as shown.
• Secure the front of the seat to the center seat support
using two M4x40mm Screws (K).
• Secure the rear seat support using four M4x40mm
Screws (K), as shown.
• Connect Front Right Leg (E1) to the inside front of Right
Armrest (C) using one M6x50mm Bolt Set (L).
• Connect Back Right Leg (F1) to the inside back of Right
Armrest (C) using one M6x50mm Bolt Set (L).
• Connect Front Left Leg (E2) to the inside front of Left
Armrest (D) using one M6x50mm Bolt Set (L).
• Connect Back Left Leg (F2) to the inside back of Left
Armrest (D) using one M6x50mm Bolt Set (L).
• Establish the front and back of Rocker Runners (H).
• Loosely connect each Rocker Runner (H) to the outside
of each arm panel using four M6x50mm Bolt Sets (L)
on each side, as shown.
TIP: Install bolt head on the
01/2022
STEP 5
G: 2
M: 4
STEP 6
L: 6
• Loosely connect two Leg Supports (G) to the inside
of the right arm panel, just above the rocker runners,
using two M6x50mm Bolts (M).
• Repeat to loosely secure the left arm panel.
• Connect the front of the seat to the front of the arm
panels using two M6x50mm Bolt Sets (L) on each side.
• Align and secure the bottom mounting holes on the back
leg and seat using one M6x50mm Bolt (L) on each side.
NOTE: the top mounting hole will be secured in the next step.
Page 3 / 4 PW-RC08
STEP 7
A: 1
N: 2
O: 2 • With assistance, align Backrest (A) with the mounting
holes on the seat and top of the armrest.
• Place one M6x90mm Bolt (O) through the top of the
armrest and the backrest. Repeat on the opposite
side of the chair.
• Place one M6x80mm Bolt (N) through back leg, seat
and bottom of the backrest. Repeat on the opposite
side of the chair.
• Place the washers on the bolts and hand-tighten the
lock nuts from each bolt set.
• Use a Phillips Screwdriver and 10mm wrench to
tighten all hardware from all steps. Tools not included.
TIP:
01/2022
WARNING:
If you experience issues with assembly or the product was damaged during shipping,
please contact our customer service team through one of the methods mentioned at the top of page 1.
To expedite response time, please have the item number and order information ready.
WARNING:
SAFE USE: For residential use only. Only use on a at, level surface. Do not stand on the chair. Do not
exceed the weight capacity of the chair.
INSPECT: Periodically check hardware and tighten as necessary.
CLEAN: Mix a mild soap and water solution and wipe surfaces with a soft, non-abrasive cloth. Rinse with
clean water, ensuring all soap residue has been removed. Do not use harsh chemicals or abrasive materials
to clean.
WINTER CARE & STORAGE: Protect from inclement weather by moving furniture to an indoor location.
Cover while in storage to help prevent dust build-up. When not in use, cover furniture with a breathable cover
to help protect it from the eects of sunlight, inclement weather, dust build-up, and collecting debris.
Care & Maintenance
• Do not exceed the weight capacity.
• Never stand on the chair.
• Inspect hardware often and tighten loose hardware before use.
• Do not put hot items on or near furniture.
• Keep furniture a safe distance from heat sources such as, but not limited to, fire pits, patio heaters, and grills.
• Do not allow children to use this product without adult supervision.
• Do not use harsh chemicals or abrasive materials to clean the furniture.
SAFETY STATEMENTS & WARNINGS
Page 4 / 4 PW-RC08 01/2022
/
