Satel Short Form User guide

Satel
Brand
Satel
Model
Short Form
Type
User guide
SATEL Short Form user guide
Version 19
1
IMPORTANT NOTICE
All rights to this manual are owned solely by SATEL Oy (referred to in this user
guide as SATEL). All rights reserved. The copying of this manual (without the written
permission from the owner) by printing, copying, recording or by any other means,
or the full or partial translation of the manual to any other language, including all
programming languages, using any electrical, mechanical, magnetic, optical,
manual or other methods or devices is forbidden.
SATEL reserves the right to change the technical specifications or functions of its
products, or to discontinue the manufacture of any of its products or to discontinue
the support of any of its products, without any written announcement and urges its
customers to ensure, that the information at their disposal is valid.
SATEL software and programs are delivered ”as is”. The manufacturer does not
grant any kind of warranty including guarantees on suitability and applicability to a
certain application. Under no circumstances is the manufacturer or the developer
of a program responsible for any possible damages caused by the use of a
program. The names of the programs as well as all copyrights relating to the
programs are the sole property of SATEL. Any transfer, licensing to a third party,
leasing, renting, transportation, copying, editing, translating, modifying into
another programming language or reverse engineering for any intent is forbidden
without the written consent of SATEL.
SATEL PRODUCTS HAVE NOT BEEN DESIGNED, INTENDED NOR INSPECTED
TO BE USED IN ANY LIFE SUPPORT RELATED DEVICE OR SYSTEM RELATED
FUNCTION NOR AS A PART OF ANY OTHER CRITICAL SYSTEM AND ARE
GRANTED NO FUNCTIONAL WARRANTY IF THEY ARE USED IN ANY OF THE
APPLICATIONS MENTIONED.
Salo, Finland 2018
NOTE! This is a short form user guide for SATEL products. Complete user
guide for each model is available in electronical format on SATEL web site
www.satel.com
SATEL Short Form user guide
Version 19
2
RESTRICTIONS ON USE
SATELLINE radio modems have been designed to operate on frequency ranges, the
exact use of which differs from one region and/or country to another. The user of a
radio modem must take care that the said device is not operated without the
permission of the local authorities on frequencies other than those specifically
reserved and intended for use without a specific permit
WARRANTY AND SAFETY INSTRUCTIONS
Read these safety instructions carefully before using the product:
Warranty will be void, if the product is used in any way that is in
contradiction with the instructions given in this manual, or if the radio
modem housing has been opened or tampered with.
The radio modem is only to be operated at frequencies allocated by local
authorities, and without exceeding the given maximum allowed output
power ratings. SATEL and its distributors are not responsible, if any products
manufactured by it are used in unlawful ways.
The devices mentioned in this manual are to be used only according to the
instructions described in this manual. Faultless and safe operation of the
devices can be guaranteed only if the transport, storage, operation and
handling of the devices are appropriate. This also applies to the
maintenance of the products.
To prevent damage both the radio modem and any terminal devices must
always be switched OFF before connecting or disconnecting the serial
connection cable. It should be ascertained that different devices used have
the same ground potential. Before connecting any power cables the output
voltage of the power supply should be checked.
WARNING! Users of SATELLINE radio modems in North America should be
aware, that due to the allocation of the frequency band 406.0 – 406.1 MHz
for government use only, the use of radio modem on this frequency band
without a proper permit is strictly forbidden.
SATEL Short Form user guide
Version 19
3
DECLARATION OF CONFORMITY
Hereby, SATEL Oy declares that SATELLINE radio modems are in compliance with
the essential requirements (radio performance, electromagnetic compatibility and
electrical safety) and other relevant provisions of Directive 2014/53/EU. Therefore
the equipment is labeled with the CE-marking (image down below).
Declaration of Conformity documents are available from the manufacturer SATEL
Oy (www.satel.com) or from local SATEL distributor.
SATEL Short Form user guide
Version 19
4
TABLE OF CONTENTS
IMPORTANT NOTICE ........................................................................................... 1
RESTRICTIONS ON USE ....................................................................................... 2
DECLARATION OF CONFORMITY ........................................................................ 3
TABLE OF CONTENTS ......................................................................................... 4
1 SATELLINE-3AS VHF ...................................................................................... 7
1.1 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS VHF (YM5000) AND -3ASD VHF
(YM5010) ........................................................................................................... 7
1.2 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS VHF C (YM5020) AND -3ASD VHF
C (YM5030) ....................................................................................................... 7
1.3 PINNING ORDER ......................................................................................... 8
2 SATELLINE-3AS NMS AND EPIC NMS .............................................................. 9
2.1 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS NMS (YM1070) AND -3ASD NMS
(YM1075) ........................................................................................................... 9
2.2 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS EPIC NMS (YM3010) AND -3AS
EPIC NMS DB (YM3014) ....................................................................................... 9
2.3 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS EPIC C NMS (YM3012), -3AS EPIC
NMS DB C (YM3016) AND -3ASD EPIC NMS DB C (YM3017) ................................... 10
2.4 PINNING ORDER ....................................................................................... 11
3 SATELLINE-3AS EPIC DB .............................................................................. 12
3.1 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS EPIC DB (YM3004) ................ 12
3.2 TECHNICAL SPECIFICATIONS FOR SATELLINE-3AS EPIC C DB (YM3006) AND
SATELLINE-3ASD EPIC C DB (YM3007) ................................................................. 12
3.3 PINNING ORDER ....................................................................................... 13
4 SATELLINE-EASY, –EASY 869, –EASY (865-867 MHZ) ...................................... 14
4.1 TECHNICAL SPECIFICATIONS FOR SATELLINE-EASY (YM6500, YM6505, YM6550,
YM6555, YM6510, YM6515, YM6560, YM6565) ................................................ 14
4.2 TECHNICAL SPECIFICATION FOR SATELLINE-EASY 869 (YM6501, YM6551) ....... 14
4.3 TECHNICAL SPECIFICATION FOR SATELLINE-EASY, 865-867 MHZ, (YM6501,
YM6551) .......................................................................................................... 15
4.4 PINNING ORDER ....................................................................................... 16
5 SATELLINE-1870E ....................................................................................... 17
5.1 TECHNICAL SPECIFICATIONS FOR SATELLINE-1870E (YM4010) ........................ 17
5.2 POWER CONSUMPTION FOR SATELLINE-1870E ............................................. 17
5.3 PINNING ORDER ....................................................................................... 18
6 SATELLINE–EASY PRO 35W, -4PRO .............................................................. 19
6.1 TECHNICAL SPECIFICATIONS FOR SATELLINE-EASY PRO 35W (YM6803 AND
YM6813) .......................................................................................................... 19
6.2 TECHNICAL SPECIFICATIONS FOR SATELLINE-4PRO (YM6804) .......................... 19
6.3 DUTY CYCLE FOR SATELLINE-EASY PRO 35W AND -4PRO ................................ 20
6.4 PINNING ORDERS ..................................................................................... 20
7 SATEL COMPACT-PROOF ........................................................................... 21
7.1 TECHNICAL SPECIFICATION FOR SATEL COMPACT-PROOF (YM6570, YM6573,
YM6571, YM6574) ........................................................................................... 21
7.2 TECHNICAL SPECIFICATION FOR SATEL COMPACT-PROOF, 869 MHZ, (YM6575,
YM6576) .......................................................................................................... 21
SATEL Short Form user guide
Version 19
5
7.3 TECHNICAL SPECIFICATION FOR SATEL COMPACT-PROOF, 865-867 MHZ,
(YM6575, YM6576) .......................................................................................... 22
7.4 SPECIFICATION FOR BATTERY ....................................................................... 22
7.5 CHARGING INDICATORS ............................................................................. 23
7.6 PINNING ORDERS ..................................................................................... 23
8 SATEL EASY-PROOF AND SATEL PROOF-TR4 / -TR9 ....................................... 24
8.1 TECHNICAL SPECIFICATION FOR SATEL EASY-PROOF (YM6580, YM6480, YM6585,
YM6485) .......................................................................................................... 24
8.2 TECHNICAL SPECIFICATION FOR SATEL PROOF-TR4 (YM6583, YM6584) / -TR9
(YM6587) ......................................................................................................... 24
8.3 PINNING ORDER ....................................................................................... 25
9 SATEL COMPACT-4BT ................................................................................ 26
9.1 TECHNICAL SPECIFICATION FOR SATEL COMPACT-4BT (YM6590, YM6591) ....... 26
9.2 PINNING ORDER FOR SATEL COMPACT-4BT .................................................. 26
10 CUSTOMIZED RADIO MODEMS AND MODULES ........................................... 27
10.1 SATELLINE-M3 VHF (YM6000) TECHNICAL SPECIFICATIONS ............................. 27
10.2 SATELLINE-M3-TR1 (YM6300, YM6305, YM6310, YM6315) TRANSCEIVER
MODULE ............................................................................................................ 27
10.3 PINNING ORDER FOR SATELLINE-M3-TR1 .................................................... 28
10.4 SATELLINE-M3-TR1 869 (YM6301) TRANSCEIVER MODULE ............................. 29
10.5 SATELLINE-M3-TR1, 865-867 MHZ, (YM6301) TRANSCEIVER MODULE ............. 29
10.6 PINNING ORDER FOR SATELLINE-M3-TR1 869 AND 865 MHZ VARIANT, 26-PIN
CONNECTOR ...................................................................................................... 30
10.7 PINNING ORDER FOR D15 FEMALE CONNECTOR ADAPTER .................................. 31
10.8 SATELLINE-M3-R3 (YM6900) RECEIVER MODULE ........................................... 32
10.9 PINNING ORDER FOR SATELLINE-M3-R3 ...................................................... 32
10.10 SATELLINE-M3-TR3 (YM7000, YM7100) AND –TR4 (YM7400, YM7405,
YM7410) TRANSCEIVER MODULES ........................................................................... 33
10.11 SATELLINE-M3-R4 (YM7050, YM7150, YM7250) RECEIVER MODULE .......... 34
10.12 PINNING ORDER FOR SATELLINE-M3-TR3, -TR4 AND -R4 ............................ 34
10.13 SATELLINE-M3-TR8 (YM7800 AND YM7810) TRANSCEIVER MODULE ............ 36
10.14 SATELLINE-M3-TR8, 865-867 MHZ, (YM7800) TRANSCEIVER MODULE ......... 36
10.15 SATELLINE-M3-TR9 (YM7900) TRANSCEIVER MODULE ................................ 37
10.16 SATEL-TR49 (YM8490, YM8495, YM8500, YM8505) TRANSCEIVER MODULE 37
10.17 PINNING ORDER FOR SATELLINE-M3-TR8, -TR9 AND –TR49 ........................ 38
11 ADDITIONAL EQUIPMENT........................................................................... 39
11.1 SATELLINK I/O-CONVERTERS ..................................................................... 39
12 ACCESSORIES ........................................................................................... 40
12.1 INTERFACE CABLES AND ADAPTERS FOR RS-232 INTERFACE ................................. 40
12.2 INTERFACE CABLES AND ADAPTERS FOR RS-485/422 INTERFACE .......................... 40
12.3 NMS CABLE ............................................................................................ 41
12.4 PROGRAMMING CABLE ............................................................................... 41
12.5 RF CABLES .............................................................................................. 41
12.6 ANTENNAS .............................................................................................. 42
12.7 POWER SUPPLIES AND POWER CABLES ............................................................ 43
12.8 FILTERS AND LIGHTNING PROTECTORS ........................................................... 43
13 SOFTWARE (MS WINDOWS COMPATIBLE) .................................................... 44
13.1 SATERM .................................................................................................. 44
13.2 SATEL NMS PC ....................................................................................... 44
SATEL Short Form user guide
Version 19
6
13.3 CONFIGURATION MANAGER ....................................................................... 44
13.4 FCS MONITOR ........................................................................................ 44
13.5 CHANNEL LIST EDITOR ................................................................................ 44
14 HOW TO ESTABLISH A WIRELESS DATA LINK ................................................. 45
14.1 LIST OF EQUIPMENT ................................................................................... 45
14.2 EQUIPMENT SETUP .................................................................................... 46
14.3 PARAMETER SETUPS .................................................................................... 46
14.4 COMMUNICATION TEST OVER THE LINK .......................................................... 46
15 SETTINGS ................................................................................................. 47
16 ERROR CORRECTION (FEC) ........................................................................ 48
17 CHECK LIST / TROUBLE SHOOTING ............................................................ 49
SATEL Short Form user guide
Version 19
7
1 SATELLINE-3AS VHF
1.1 Technical specifications for SATELLINE-3AS VHF (YM5000) and -
3ASd VHF (YM5010)
The model SATELLINE-3ASd VHF (YM5010) is equipped with LCD and push-
buttons.
Subject
Value
Frequency range
135 … 174 / 218 … 238 MHz
Tuning range
135 … 155, 138 … 160 MHz
155 … 174, 218 … 238 MHz
Channel spacing
12.5 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 5 W
Interface
RS-232, 422, 485
Operating voltage
+9 … +30 Vdc
Power consumption RX / TX
1.7 W / 6.6 W @ 1 W, 22 W @ 5 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
137 x 67 x 29 mm
Weight
265 g
1.2 Technical specifications for SATELLINE-3AS VHF C (YM5020)
and -3ASd VHF C (YM5030)
Both models are equipped with a heat sink, which is the appropriate choice for
continuous transmission.
The model SATELLINE-3ASd VHF C (YM5030) is equipped with LCD and push-
buttons.
Subject
Value
Frequency range
135 … 174 / 218 … 238 MHz
Tuning range
135 … 155, 138 … 160 MHz
155 … 174, 218 … 238 MHz
Channel spacing
12.5 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 5 W
Interface
RS-232, 422, 485
Operating voltage
+9 … +30 Vdc
Power consumption RX / TX
1.7 W / 6.6 W @ 1 W, 22 W @ 5 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
137 x 80 x 56 mm
Weight
550 g
SATEL Short Form user guide
Version 19
8
1.3 Pinning order
D15 female connector in radio modem.
o DTE is an abbreviation for Data Terminal Equipment
o DIR. column below denotes the direction of the signal:
"IN" is from DTE to the radio modem, "OUT"is from the radio modem to the DTE.
PIN
NAME
LEVEL
EXPLANATION
1
DTR
0..30V
Data Terminal Ready. The pin can be used to wake-up the
radio module from the standby mode. >+2 VDC = ON,
Not connected = ON, <+0.6 VDC = STANDBY
2
Pin 2 has alternative functions depending on the
Port2
configuration, see below.
CD
RS-232
Carrier Detect (if
Port2
selection is RS-232)
A’
RS-422
Port2
Receive Data positive (if
Port2
selection is RS-422)
A
RS-485
Port2
Data positive.
Note
**) (if
Port2
selection is RS-485)
3
Pin 3 has alternative functions depending on the
Port2
configuration, see below.
RD2
RS-232
Port2
Receive Data (if
Port2
selection is RS-232)
B’
RS-422
Port2
Receive Data negative (if
Port2
selection is RS-422)
B
RS-485
Port2
Data negative.
Note
**) (if
Port2
selection is RS-485)
4
Pin 4 has alternative functions depending on the configuration, see below.
TD2
RS-232
Port2
Transmit Data (if
Port2
selection is RS-232)
A
RS-422
Port2
Transmit Data positive (if
Port2
selection is RS-422)
5
Pin 5 has alternative functions depending on the hardware assembly, see below.
B
RS-422
Port2
Transmit data negative (default hardware)
RSSI
0..5V
Analogue RSSI (requires the special hardware assembly,
needs to be defined in order sheet!)
6
CTS
RS-232
Clear To Send. This signal indicates that the radio modem
serial interface is ready to receive data from DTE.
Note
*)
7, 8
GND
Operating voltage and Signal Ground
9
RD1
RS-232
Port1
Receive Data to DTE from the radio modem
10
DSR
RS-232
Data Set Ready. Indicates that the radio modem is ON.
11
TD1
RS-232
Port1
Transmit Data from DTE to the radio modem.
12
MODE
0..30V
<2VDC or connected to ground =
Programming Mode
>3VDC or Not connected =
Data Transfer Mode Note
***)
13
RTS
RS-232
Request To Send from DTE.
Note
*)
14,
15
V
b
+9...30
VDC
Operating Voltage.
Note!
Unused pins can be left unconnected.
Note
*) RTS and CTS signals apply to the Data port-either
Port1
or
Port2
depending on the
configuration.
Note
**) A and B designators are opposite in Profibus standard.
Note
***)
Programming Mode
is for changing the settings of the radio modem via
Programming
menu
. Normally the MODE line is NOT connected i.e. the radio modem is in
Data Transfer Mode
.
SATEL Short Form user guide
Version 19
9
2 SATELLINE-3AS NMS and Epic NMS
2.1 Technical specifications for SATELLINE-3AS NMS (YM1070) and
-3ASd NMS (YM1075)
The model SATELLINE-3ASd NMS (YM1075) is equipped with LCD and push-
buttons.
Subject
Value
Frequency range
330 … 470 MHz
Tuning range
± 2 MHz from central freq.
Channel spacing
12.5 / 20 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 1 W
Interface
RS-232, 422, 485
Operating voltage
+9 … +30 Vdc
Power consumption RX / TX
1.4 W / 6 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
137 x 67 x 29 mm
Weight
250 g
2.2 Technical specifications for SATELLINE-3AS Epic NMS (YM3010)
and -3AS Epic NMS DB (YM3014)
Models support diversity reception.
Frequency tuning range is +/- 2 MHz from the central frequency. Model YM3014
has Dual Band function offering 2 x 2 MHz frequency bands with maximum 15
MHz separation between the highest and lowest frequency.
Subject
Value
Frequency range
330 … 470 MHz (YM3010)
412.5 … 457.5 MHz (YM3014)
Tuning range
± 2 MHz from central freq.
Channel spacing
12.5 / 20 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 10 W
Interface
RS-232, 422, 485
Operating voltage
+11.8 … +30 Vdc
Power consumption RX / TX
1.6 W / 36 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
154 x 123 x 29 mm
Weight
580 g
SATEL Short Form user guide
Version 19
10
2.3 Technical specifications for SATELLINE-3AS Epic C NMS
(YM3012), -3AS Epic NMS DB C (YM3016) and -3ASd Epic NMS
DB C (YM3017)
Models support diversity reception and are equipped with a heat sink, which is the
appropriate choice for continuous transmission.
Models YM3016 and YM3017 are with Dual Band function. In addition YM3017
is equipped with LCD and push-buttons.
Subject
Value
Frequency range
330 … 470 MHz (YM3012)
412.5 … 457.5 MHz (YM3016, YM3017)
Tuning range
± 2 MHz from central freq.
Channel spacing
12.5 / 20 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 10 W
Interface
RS-232, 422, 485
Operating voltage
+11.8 … +30 Vdc
Power consumption RX / TX
1.6 W / 36 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
154 x 151 x 77 mm
Weight
1480 g
SATEL Short Form user guide
Version 19
11
2.4 Pinning order
D15 female connector in radio modem.
o DTE is an abbreviation for Data Terminal Equipment
o DIR. column below denotes the direction of the signal:
"IN" is from DTE to the radio modem, "OUT"is from the radio modem to the DTE.
PIN
NAME
LEVEL
EXPLANATION
1
DTR
0..30V
Data Terminal Ready. The pin can be used to wake-up the
radio module from the standby mode. >+2 VDC = ON,
Not connected = ON, <+0.6 VDC = STANDBY
2
Pin 2 has alternative functions depending on the
Port2
configuration, see below.
CD
RS-232
Carrier Detect (if
Port2
selection is RS-232)
A’
RS-422
Port2
Receive Data positive (if
Port2
selection is RS-422)
A
RS-485
Port2
Data positive.
Note
**) (if
Port2
selection is RS-485)
3
Pin 3 has alternative functions depending on the
Port2
configuration, see below.
RD2
RS-232
Port2
Receive Data (if
Port2
selection is RS-232)
B’
RS-422
Port2
Receive Data negative (if
Port2
selection is RS-422)
B
RS-485
Port2
Data negative.
Note
**) (if
Port2
selection is RS-485)
4
Pin 4 has alternative functions depending on the configuration, see below.
TD2
RS-232
Port2
Transmit Data (if
Port2
selection is RS-232)
A
RS-422
Port2
Transmit Data positive (if
Port2
selection is RS-422)
5
Pin 5 has alternative functions depending on the hardware assembly, see below.
B
RS-422
Port2
Transmit data negative (default hardware)
RSSI
0..5V
Analogue RSSI (requires the special hardware assembly,
needs to be defined in order sheet!)
6
CTS
RS-232
Clear To Send. This signal indicates that the radio modem
serial interface is ready to receive data from DTE.
Note
*)
7, 8
GND
Operating voltage and Signal Ground
9
RD1
RS-232
Port1
Receive Data to DTE from the radio modem
10
DSR
RS-232
Data Set Ready. Indicates that the radio modem is ON.
11
TD1
RS-232
Port1
Transmit Data from DTE to the radio modem.
12
MODE
0..30V
<2VDC or connected to ground =
Programming Mode
>3VDC or Not connected =
Data Transfer Mode Note
***)
13
RTS
RS-232
Request To Send from DTE.
Note
*)
14,
15
V
b
See
above
Operating Voltage.
+11.8...30 VDC for 3AS Epic NMS
+9...30 VDC for 3AS NMS
Note!
Unused pins can be left unconnected.
Note
*) RTS and CTS signals apply to the Data port-either
Port1
or
Port2
depending on the
configuration.
Note
**) A and B designators are opposite in Profibus standard.
Note
***)
Programming Mode
is for changing the settings of the radio modem via
Programming
menu
. Normally the MODE line is NOT connected i.e. the radio modem is in
Data Transfer Mode
.
SATEL Short Form user guide
Version 19
12
3 SATELLINE-3AS Epic DB
3.1 Technical specifications for SATELLINE-3AS Epic DB (YM3004)
Model supports diversity reception.
Frequency tuning range is +/- 2 MHz from the central frequency or with Dual
Band function 2 x 2 MHz frequency bands with maximum 15 MHz separation
between the highest and lowest frequency.
Subject
Value
Frequency range
397.5 … 470 MHz
Tuning range
± 2 MHz from central freq.
Channel spacing
12.5 / 20 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 10 W
Interface
RS-232, 422, 485
Operating voltage
+11.8 … +30 Vdc
Power consumption RX / TX
1.6 W / 32 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
154 x 123 x 29 mm
Weight
580 g
3.2 Technical specifications for SATELLINE-3AS Epic C DB (YM3006)
and SATELLINE-3ASd Epic C DB (YM3007)
Models support diversity reception and are equipped with a heat sink, which is the
appropriate choice for continuous transmission.
Frequency tuning range as with YM3004. The model SATELLINE-3ASd Epic C DB
(YM3007) is equipped with LCD and push-buttons.
Subject
Value
Frequency range
397.5 … 470 MHz
Tuning range
± 2 MHz from central freq.
Channel spacing
12.5 / 20 / 25 kHz fixed
RX Sensitivity / TX power max.
-115 dBm / 10 W
Interface
RS-232, 422, 485
Operating voltage
+11.8 … +30 Vdc
Power consumption RX / TX
1.6 W / 32 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
154 x 151 x 77 mm
Weight
1480 g
SATEL Short Form user guide
Version 19
13
3.3 Pinning order
D15 female connector in radio modem.
PORT AND TYPE
PIN
DIRECTION
NAME
EXPLANATION
PORT1, both models
6
OUT
CTS
*
9
OUT
RD1
Receive data (Port1)
11
IN
TD1
Transmit data (Port1)
13
IN
RTS
*
PORT2 RS-232 model
2
OUT
CD
3
OUT
RD2
Receive data (Port2)
4
IN
TD2
Transmit data (Port2)
5
OUT
RSSI
Analog RSSI (Optional
HW)
PORT2 RS-422 model
2
OUT
A’
Receive data positive
3
OUT
B’
Receive data negative
4
IN
A
Transmit data positive
5
IN
B
Transmit data negative
PORT2 RS-485 model
2
IN / OUT
A
Data positive **)
3
IN / OUT
B
Data negative **)
COMMON PINS
1
IN
DTR
ON (V
b
) / STANDBY (NC)
10
OUT
DSR
12
IN
MODE
DATA (NC) / SETUP
(GND)
7, 8
-
GND
Power Ground
14, 15
-
V
b
Operating Voltage
Direction IN is from DTE (Data Terminal Equipment) to the radio modem. Direction
OUT is from the radio modem to the DTE.
NOTE! Unused pins can be left unconnected.
*) RTS and CTS handshaking connections remain the same irrespective of the port
used (Port 1 or Port 2).
**) A and B designators are opposite in Profibus standard.
SATEL Short Form user guide
Version 19
14
4 SATELLINE-EASy, –EASy 869, –EASy (865-867 MHz)
4.1 Technical specifications for SATELLINE-EASy (YM6500, YM6505,
YM6550, YM6555, YM6510, YM6515, YM6560, YM6565)
The models SATELLINE-EASy YM6550, YM6555, YM6560 and YM6565 are
equipped with LCD and push-buttons. Models YM6510, YM6515, YM6560 and
YM6565 are with AES128 encryption support.
Subject
Value
Frequency range
330 … 420 / 403 … 473 MHz
Tuning range
90 / 70 MHz
Channel spacing
12.5 / 20 / 25 kHz selectable
RX Sensitivity / TX power max.
-114 dBm / 1 W
Interface
Port1: RS-232 fixed
Port2: LVTTL, TTL or RS-232 / 422
Operating voltage
+3 … +9 / +6 … +30 Vdc
Power consumption RX / TX
1.2 W / 7 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
137 x 67 x 29 mm
Weight
250 g
4.2 Technical specification for SATELLINE-EASy 869 (YM6501,
YM6551)
The model SATELLINE-EASy 869 YM6551 is equipped with LCD and push-buttons.
Subject
Value
Frequency range
869.4125 … 869.6375 MHz
Tuning range
10 channels
Channel spacing
25 kHz fixed
RX Sensitivity / TX power max.
-111 dBm / 500 mW
Interface
Port1: RS-232/Port2: LVTTL, TTL or RS-
232/422
Operating voltage
+6 … +30 Vdc
Power consumption RX / TX
1.2 W / 3.8 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
139 x 67 x 29 mm
Weight
250 g
SATEL Short Form user guide
Version 19
15
According to a recommendation of ETSI, the frequencies range 869.4…869.65
MHz is reserved for use of license free radio appliances. The application of this
recommendation varies in each country, and for this reason local regulations
concerning this frequency range must always be checked.
In frequency range 869.4…869.65 MHz, the maximum allowed radiated power of
an antenna is 500 mW ERP (+27dBm). When calculating the power, antenna
cable attenuation and antenna gain must be taken into account. For example, if
the gain of the antenna is 10 dBd and the attenuation of the antenna cable used is
–3dB, the maximum allowed transmission power is 100 mW (+20 dBm). It should
be noted that by increasing the gain of the antennas, connection distance could be
increased. This is due to the fact that the output power of the transmission remains
constant, but the added antenna gain of the receiving end will enable reception of
weaker signals than otherwise possible.
System designers must take into account that at the frequency range of 869.4 …
869.65 MHz the transmitter is allowed to be ON only 10% of the time. Whether
this limit is exceeded or not, depends on the protocol used. At a frequency range
of 869 MHz there are in addition to the frequency channel 869.4…869.65 MHz
also other ranges, but at these ranges the maximum allowed radiated power is 25
mW and the transmitter is allowed to be ON only 1 % or 0.1 % of the time.
4.3 Technical specification for SATELLINE-EASy, 865-867 MHz,
(YM6501, YM6551)
The model SATELLINE-EASy, 865-867 MHz, YM6551 is equipped with LCD and
push-buttons.
These variants of SATELLINE-EASy are ready to use on the Indian licence free
channels.
Subject
Value
Frequency range
865 … 867 MHz
Tuning range
2 MHz
Channel spacing
25 kHz fixed
RX Sensitivity / TX power max.
-111 dBm / 1 W
Interface
Port1: RS-232/Port2: LVTTL, TTL or RS-
232/422
Operating voltage
+6 … +30 Vdc
Power consumption RX / TX
1.2 W / 7 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
D15 / TNC female
Size H x W x D
139 x 67 x 29 mm
Weight
250 g
SATEL Short Form user guide
Version 19
16
4.4 Pinning order
D15 female connector in radio modem.
PORT AND TYPE
PIN
DIRECTION
NAME
EXPLANATION
PORT1: RS-232
6
OUT
CTS
*
9
OUT
RD1
Receive data (Port1)
11
IN
TD1
Transmit data (Port1)
13
IN
RTS
*
PORT2: RS-232 / 422
232 ON / 422 OFF
2
OUT
CD
3
OUT
RD2
Receive data (Port2)
4
IN
TD2
Transmit data (Port2)
5
OUT
-
-
PORT2: RS-232 / 422
422 ON / 232 OFF
2
OUT
A’
Receive data positive
3
OUT
B’
Receive data negative
4
IN
A
** Transmit data positive
5
IN
B
** Transmit data negative
PORT2: LVTTL
2
OUT
CTS
*
3
OUT
RD
Receive data (Port2)
4
IN
TD
Transmit data (Port2)
5
IN
RTS
*
PORT2: TTL
2
OUT
CTS
*
3
OUT
RD
Receive data (Port2)
4
IN
TD
Transmit data (Port2)
5
IN
RTS
*
COMMON PINS
1
IN
DTR
ON (V
b
or NC) / STANDBY
(GND)
10
OUT
DSR
12
IN
MODE
DATA (NC) / SETUP (GND)
7, 8
-
GND
Power Ground
14, 15
-
V
b
Operating Voltage
Direction IN is from DTE (Data Terminal Equipment) to the radio modem.
Direction OUT is to the DTE from the radio modem.
NOTE! Unused pins can be left unconnected.
*) RTS and CTS handshaking connections remain the same irrespective of the port
used (Port 1 or Port 2).
**) A and B designators are opposite in Profibus standard.
SATEL Short Form user guide
Version 19
17
5 SATELLINE-1870E
5.1 Technical specifications for SATELLINE-1870E (YM4010)
Subject
Value
Frequency range
868 … 870 MHz
Tuning range
2 MHz
Channel spacing
25 kHz fixed
RX Sensitivity / TX power max.
-108 dBm / 500 mW
Interface
RS-232
Operating voltage
+8 … +30 Vdc
Data speed radio max. / serial
9600 / 19200 bps
Connectors
DIN41650-16 pin male / SMA female
Size H x W x D
125 x 57 x 16 mm
Weight
125 g
System designers must take into account that at the frequency range of 869.4 …
869.65 MHz the transmitter is allowed to be ON only 10% of the time. Whether
this limit is exceeded or not, depends on the protocol used. At a frequency range
of 869 MHz there are in addition to the frequency channel 869.4…869.65 MHz
also other ranges, but at these ranges the maximum allowed radiated power is 25
mW and the transmitter is allowed to be ON only 1 % or 0.1 % of the time.
5.2 Power consumption for SATELLINE-1870E
Input
Voltage
(V)
Operating Mode (typical values)
Receive
(mA)
Transmit on different power levels (mA)
500 mW 100 mW 5 mW
Power
save (mA)
Standby
(µA)
8
136
444
244
168
25
55
12
89
296
166
105
19
62
30
40
128
76
47
13
1717
SATEL Short Form user guide
Version 19
18
5.3 Pinning order
DIN41651-16 pin male
connector of the radio modem
(the modem DTE-connector
facing the viewer).
PIN
DIR.
NAME
EXPLANATION
RS-232 PINS
9
OUT
DSR
Data set ready
Instruction: Indicates that the radio modem is switched ON
(internally connected to the DTR pin). Connecting a load to DSR
without connecting a driving source to DTR cause the modem to
enter the STBY mode.
10
OUT
RD
Receive Data, Output of the data received over radio. Data from
the radio modem to the DTE.
11
IN
RTS
Request to send, Handshake signal.
12
IN
TD
Transmit Data, input of the data to be transmitted by radio. Data
from the DTE to the radio modem.
13
OUT
CTS
Clear to send, Handshake signal can be used to drive external
interface converters.
14
IN
DTR
Data Terminal Ready, modem ON/OFF, active low.
Instruction: When left unconnected the radio modem is ON (weak
pull-up) *. When connected to GND or SGND the radio modem
will enter the Standby Mode.
COMMON PINS
1,3
DC
Vb
DC supply voltage, positive
2,4
DC
GND
DC return, negative DC input, internally connected to SGND
5
IN
NC
Do not connect
6
IN
SHDN
Modem power down, active low, weak pull-up. *
7
IN
PROG
Operational mode, active low, weak pull-up. *
Instruction: When the connected to ground (GND/SGND), the
radio modem enters the Programming Mode which is for changing
the settings of the radio modem (i.e. configuration, set-up). If the
PROG-line is not connected, the radio modem will enter the Data
Transfer Mode, in which data can be transmitted and received. The
Programming Mode is used only when installing a radio modem
and changing the parameters of a modem.
8
OUT
VDD_
AUX
Regulated 5.5 V (5.3….5.7 V) DC output. Max load 100 mA.
Intended to power external devices made by Satel (e.g i-LINK).
15
-
NC
Not connected
16
IN
SGND
Signal ground, internally connected to GND.
*) NOTE! For cables > 1m the DTR should not be left unconnected in order to
prevent disturbances from pulling DTR low and thus shutting down the modem.
SATEL Short Form user guide
Version 19
19
6 SATELLINE–EASy Pro 35W, -4Pro
6.1 Technical specifications for SATELLINE-EASy Pro 35W (YM6803
and YM6813)
The model YM6813 is with AES128 encryption support.
Subject
Value
Frequency range
403 … 473 MHz
Tuning range
70 MHz
Channel spacing
12.5 / 20 / 25 kHz selectable
RX Sensitivity / TX power max.
-114 dBm / 25* or 35 W
Interface
RS-232
Operating voltage
+9 … +16 Vdc (≥ +12 Vdc @ 35 W)
Power consumption
RX
TX
1.8 W
100 W @ 25 W / 120 W @ 35 W
Data speed radio max. / serial
19200 / 38400 bps
Connectors
8-pin ODU / 4-pin ODU / TNC female
Size H x W x D
189 x 138 x 71 mm
Weight
1420 g
IP classification
IP67 (NEMA6)
* Limited 25 W output power is available as an order option.
6.2 Technical specifications for SATELLINE-4Pro (YM6804)
Subject
Value
Frequency range
406.1 … 470 MHz
Tuning range
63.9 MHz
Channel spacing
12.5 / 25 kHz selectable
RX Sensitivity / TX power max.
-117 dBm / 35 W
Interface
RS-232
Operating voltage
+9 … +16 Vdc
Power consumption
RX
TX
1.8 W
100 W @ 25 W / 120 W @ 35 W
Data speed radio max. / serial
28800 / 115200 bps
Connectors
8-pin ODU / 4-pin ODU / TNC female
Size H x W x D
189 x 138 x 71 mm
Weight
1420 g
IP classification
IP67 (NEMA6)
SATEL Short Form user guide
Version 19
20
6.3 Duty cycle for SATELLINE-EASy Pro 35W and -4Pro
If high output power is used continuously or with a high cycle, the equipment
generates excess heat. The output power is automatically decreased when
necessary to prevent overheating.
Duty cycle
100 % (22
o
C / 35
o
C)
40 %
Output power 35 W
20 min / 13 min
No limit
Output power 10 W
No limit / 20 min
No limit
6.4 Pinning orders
a) SATELLINE–EASy Pro 35W and -4Pro
Connector: 8-pin ODU, MINI-SNAP
1
RTS
2
CTS
3
SGND
4
RD
5
TD
6
PROG
7
Not connected
8
Not connected
b) Power connector SATELLINE-EASy Pro 35W and -4Pro
Connector: 4-pin ODU MINI-SNAP Style G4 size 1
1
PWR (+)
2
PWR (+)
3
GND
4
GND
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49

Satel Short Form User guide

Satel
Brand
Satel
Model
Short Form
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents