Hubbell IS600PLUGS will help you to insulate or provide a tap off a T-body or Bushing Extender. It's designed to meet all requirements of IEEE Std. 386. When properly mated, the device provides a fully shielded, fully submersible unit. Possible use cases:
- Can be used for voltage testing on an energized 600A T-body.
- Can be used to indirectly test for voltage on an energized 600A T-body, either the insulating plug or the TP on the housing. Key features:
- 25/28kV Class:, 16.2kV
- 35kV Class: 21.1kV
- Lubricant included in the package
- Easy to install and operate
- Safe to use
Hubbell IS600PLUGS will help you to insulate or provide a tap off a T-body or Bushing Extender. It's designed to meet all requirements of IEEE Std. 386. When properly mated, the device provides a fully shielded, fully submersible unit. Possible use cases:
- Can be used for voltage testing on an energized 600A T-body.
- Can be used to indirectly test for voltage on an energized 600A T-body, either the insulating plug or the TP on the housing. Key features:
- 25/28kV Class:, 16.2kV
- 35kV Class: 21.1kV
- Lubricant included in the package
- Easy to install and operate
- Safe to use
Hubbell Deadbreak Plug & Well Products
25/28kV & 35kV, BIP, CP, RTW
IS600PLUGS
Installation & Operating Instructions
IS600PLUGS Rev. D 6/20
Important: Read these instructions thoroughly before operating the system.
Be sure that the terminations are rated for their intended energized use.
! CAUTION
Remove all protective shipping caps and replace with an approved insulating cap or connector prior to the junction being
submersed or the circuit energized. The protective shipping caps are intended to keep the interfaces clean during shipping
and handling and should never be used on energized equipment.
The equipment covered by these instructions should be installed, operated and serviced only by competent personnel
familiar with safety practices. This instruction is written for such personnel and is not intended as a substitute for adequate
training and experience in safe procedures for this type of equipment.
! WARNING
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be
met in connection with installation, operation or maintenance. Should further information be desired or should particular problems
arise which are not covered suciently for the purchaser’s purposes, the matter should be referred to Hubbell Power Systems, Inc.
hubbellpowersystems.com
DESCRIPTION
The Basic Insulating Plug, Connecting Plug or
Reducing Tap Well is used to insulate or provide
a tap o a T-body or Bushing Extender. They
are designed to meet all requirements of IEEE
Std. 386.
When properly mated, they provide a fully
shielded, fully submersible unit.
25/28kV Class:, 16.2kV
35kV Class: 21.1kV
NOTES
Check contents to ensure that it is complete and
the components are NOT damaged.
CONTENTS OF PACKAGE
(1) Plug, Well, or Reducer
(1) Lubricant
(DO NOT SUBSTITUTE)
(1) Instruction Sheet
INSTALLATION TOOLS
• Spanner Wrench - (RTW)
• 1” Socket - (BIP)
• 5/16” Allen Wrench - (CP)
• Torque Wrench
• Hand Tool
©2020 Hubbell Incorporated.
Because Hubbell has a policy of continuous product improvement,
we reserve the right to change design and specifications without notice.
Printed in the U.S.A. | TD_03_083E
1850 Richland Ave. East • Aiken, SC 29801 | Phone: 573-682-5521
Fax: 573-682-8714 | E-mail: [email protected].com
hubbellpowersystems.com
IS600PLUGS Rev. D 6/20
INSTALLATION
Step 1 - Clean & Lubricate
• Remove protective shipping caps.
• Clean and lubricate both the plug or well and the T-body or
Bushing Extender interface with lubricant supplied.
DO NOT SUBSTITUTE
• Hand tighten the loose stud into the plug or well if the mating
interface is not equipped with one. (Figure 1)
Step 2 – Assemble
• Push the plug or well into the T-body or Bushing Extender and
engage the threads.
• Hand tighten to prevent cross-threading. (Figure 2)
• Tighten Basic Insulating Plug or Connecting Plug to
50-60ft lbs of torque.
• Tighten Reducing Tap Well with spanner wrench. The indicated
torque will not be the actual torque due to theaddition of the
spanner wrench. Tighten 40-48 ft lbs of torque.
Step 3 – Assemble TP Cap
• For Insulating Plug, clean and lubricate inner surface of test
point cap.
• Push cap onto the 1” hex until it snaps in place. (Figure 3)
Voltage Test
There are two methods to indirectly test for voltage on an energized
600A T-body, either the insulating plug or the TP on the housing.
(Figure 4)
• Remove test point cap with a hotstick, peeling it o at an angle.
• Using a suitable sensing device, proceed to determine if the
cable is energized.
WARNING: The test point is a capacitance device; it is not directly
connected to the conductor. It requires the use of specially
designed instruments. DO NOT USE CONVENTIONAL VOLTAGE
MEASURING EQUIPMENT. A FALSE INDICATION MAY BE
OBTAINED.
• After voltage detection has been made, clean and lubricate test
point cap and replace.
Figure 1
Figure 2
Figure 3
Figure 4
Voltage Test on the
625TBT T-Body
-
1
-
2
Hubbell IS600PLUGS will help you to insulate or provide a tap off a T-body or Bushing Extender. It's designed to meet all requirements of IEEE Std. 386. When properly mated, the device provides a fully shielded, fully submersible unit. Possible use cases:
- Can be used for voltage testing on an energized 600A T-body.
- Can be used to indirectly test for voltage on an energized 600A T-body, either the insulating plug or the TP on the housing. Key features:
- 25/28kV Class:, 16.2kV
- 35kV Class: 21.1kV
- Lubricant included in the package
- Easy to install and operate
- Safe to use
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hubbell IS-600PLUGS Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Eaton COOPER POWER SERIES Installation Instructions Manual
-
-
Hubbell Power Systems IS628BT Operating instructions
-
Hubbell Power Systems IS635BT Operating instructions
-
Hubbell Power Systems Deadbreak Connectors 15kV & 25kV 600/900 Amp Products (AIK-CABA-IOM-EN-00612 WEB) Installation guide
-
Star RTW**E Owner's manual
-
ABB Elastimold 252LR Quick Manual
-
Eaton 600 A 15 kV class push-OP Installation Instructions Manual
-
WEG Electronic Relays User manual
