Eastwood After Blast Metal Prep Operating instructions

Brand
Eastwood
Model
After Blast Metal Prep
Type
Operating instructions

Eastwood After Blast Metal Prep:

Eastwood After Blast Metal Prep is a cleaner and protectant for freshly blasted metal surfaces. It promotes paint and powder adhesion and prevents flash rust. It is a phosphoric acid-based cleaner that is easy to use. Simply apply it to the metal surface and allow it to sit for 2-5 minutes. Then, wipe it off with a clean rag. No rinsing is necessary.

Capabilities:

  • Cleans and protects freshly blasted metal surfaces
  • Promotes paint and powder adhesion
  • Prevents flash rust
  • Easy to use
  • No rinsing necessary

Possible Use Cases:

  • Preparing metal surfaces for painting or powder coating

Eastwood After Blast Metal Prep:

Eastwood After Blast Metal Prep is a cleaner and protectant for freshly blasted metal surfaces. It promotes paint and powder adhesion and prevents flash rust. It is a phosphoric acid-based cleaner that is easy to use. Simply apply it to the metal surface and allow it to sit for 2-5 minutes. Then, wipe it off with a clean rag. No rinsing is necessary.

Capabilities:

  • Cleans and protects freshly blasted metal surfaces
  • Promotes paint and powder adhesion
  • Prevents flash rust
  • Easy to use
  • No rinsing necessary

Possible Use Cases:

  • Preparing metal surfaces for painting or powder coating
AFTER BLAST
Phosphoric Acid and
Water-Soluble Cleaning Solution
Net wt. 1 Gallon / 3.78 Liters 11971ZP
• Cleans and Protects Freshly-Blasted
Metal With A Zinc Phosphate Coating
• Promotes Paint and Powder Adhesion
EASTWOOD AFTER BLAST was
developed to clean, prep and prepare the
freshly blasted metal for paint or powder
coat. Use after abrasive blasting or sanding
operations for excellent paint adhesion.
1. Wear gloves and eye protection and
always apply in a well ventilated area.
Do not ingest.
2. Apply After Blast to mechanically
blasted or sanded bare steel, cast iron
or aluminum.
DO NOT use on Chrome, galvanized,
magnesium,rubber, plastic, polished or
painted surfaces.
3. Pour product from gallon container into
a small pump spray bottle.
4. Liberally spray the component and
protect the floor with plastic or paper.
5. Continue to spray small areas and
allow the product to sit for 2-5 minutes.
After that time period thoroughly wipe
the area with clean rags.
6. Re-apply until the component and rags
are free of contaminants.
7. No rinsing is necessary and once the
surface is dry coatings can be applied.
Manufactured for The Eastwood Company,
263 Shoemaker Road, Pottstown, PA 19464
1-800-343-9353 www.eastwood.com
Only in the Event of a Chemical Emergency
Involving A Spill, Leaks, Fire, or Exposure
Call Chemtrec Toll Free Day or Night:
1-800-424-9300 International
Call Collect: (202) 483-7616
PRODUCT SPECIFICATIONS:
Phosphoric Acid and water soluble cleaning
agents assure a clean and paint/powder-ready
surface with zinc phosphate coating that will
prevent flash rust and offer excellent coating ad-
hesion. NOTE: Phosphoric acid-based cleaner.
DO NOT allow product to dry on surface. DO
NOT allow product to dry on concrete floors or
contact polished, painted or chrome surface.
DANGER: Corrosive: Product
may cause skin burns, eye dam-
age, or destroy metal. Wear rubber
gloves and eye protection. Use in a
well ventilated area. Do not ingest.
If ingested, seek immediate medical attention.
PRODUCT SAFETY:
• Wear rubber gloves and eye protection
• Do not allow product to dry on surface
• Do not use on chrome, rubber, plastic,
polished or painted surfaces
• Use in well ventilated area
• Do not ingest. If ingested, seek
immediate medical attention.
Label #11971ZPL 5/20 Rev 2
© Copyright 2020
Eastwood Automotive Group LLC
  • Page 1 1

Eastwood After Blast Metal Prep Operating instructions

Brand
Eastwood
Model
After Blast Metal Prep
Type
Operating instructions

Eastwood After Blast Metal Prep:

Eastwood After Blast Metal Prep is a cleaner and protectant for freshly blasted metal surfaces. It promotes paint and powder adhesion and prevents flash rust. It is a phosphoric acid-based cleaner that is easy to use. Simply apply it to the metal surface and allow it to sit for 2-5 minutes. Then, wipe it off with a clean rag. No rinsing is necessary.

Capabilities:

  • Cleans and protects freshly blasted metal surfaces
  • Promotes paint and powder adhesion
  • Prevents flash rust
  • Easy to use
  • No rinsing necessary

Possible Use Cases:

  • Preparing metal surfaces for painting or powder coating
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents