Philips intelligent remote control User manual

user guide

Intelligent Remote Control User Guide

The information in this manual is copyright-protected. No part of this manual may be copied or

reproduced in any form without prior written consent from Philips Electronics Corporation.

PHILIPS ELECTRONICS CORPORATION SHALL NOT BE LIABLE FOR OMISSIONS OR

FOR TECHNICAL OR EDITORIAL ERRORS CONTAINED IN THIS MANUAL. PHILIPS

ELECTRONICS CORPORATION SHALL NOT BE HELD LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING FROM THE SUPPLYING OR USE OF THIS

INFORMATION. PHILIPS ELECTRONICS CORPORATION SHALL NOT BE HELD LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE

PERFORMANCE OR USE OF THE MATERIALS DESCRIBED IN THIS MANUAL.

The information in this manual may be subject to change without prior notice.

All other brand or product names are trademarks or registered trademarks of their respective companies

or organizations.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable

protection against harmful interference in residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a different circuit from the receiver.

Consult the dealer or an experienced radio/TV technician for help.

NOTE: If serial or parallel ports are configured, a filtered/shielded serial or parallel cable is

recommended to minimize EMI and ensure FCC B compliance.

User Guide

Intelligent Remote Control

customizable/programmable, touch screen

universal remote control

Insert batteries

Insert 4 AA batteries according to the picture

on the inside of the battery compartment.

OR

Use the rechargeable battery pack included

with the dock. (Remove the AA battery tray

first). Before using the remote control, be sure

to charge the battery completely according to

the instructions in the manual.

Touch the screen to start

To turn on the screen, tap it gently with your finger.

To use the touchscreen, simply tap the images you

see on the screen.

There's no need to turn the screen off–it shuts off

automatically to save power.

Operate your components

Fresh out of the box, the remote control is set up to work with popular components

made by Philips, Marantz and certain other companies. If someone has programmed

the remote control for you, it will operate all your components. If not, you need to

teach it.Teaching the remote control is easy:Add components to the Device menu, if

necessary. Then, teach the remote control the commands for the components. For

instructions, refer to the manual.

Be sure to read the manual for

important information about care and

use of the touchscreen

Battery compartment lid slides off

quickstart

Home

If you get lost, you

can always go Home.

Just tap

Tap name of

component

to display

component’s

control panels

You can also use the

Device menu; tap

here to display it.

Tap to scroll to

next panel for this

component.

Learning eye

(bottom of remote control)

For learning commands from

other remote controls

Sending eye

(IR transmitter)

Send commands to devices

Home

Easy access to all

components

Macro menu

Execute stored lists

of commands

Control panel

Tap buttons to send

commands to

components

Panel number

Shows what panel

you’re onl l

Left and Right buttons

Activate the commands

shown immediately

above the buttons

Modes

Normal use controlling components.

Learn commands from other remote controls.When a macro panel

is displayed, this button changes to for recording macros.

Assign letters and symbols to buttons and commands.

Add a new component or group of macros.

Delete a button, component, macro, or macro group.

Change the order of commands in a menu.

quickreference

The remote control icon

Press and hold for 3

seconds to go to Setup

Scroll button

Display previous

control panel

Device menu

Open a component’s

control panels

Mode menu

Customize the remote

control (see below)

Scroll button

Display next control

panel. Scroll buttons

may appear on left

4

Contents

Welcome 7

Features 8

The intelligent remote control 8

Recharging dock 8

1 Batteries 9

Installing AA batteries 9

Using the recharging dock 11

2 Using the remote control 14

Buttons and controls 14

Direct-access buttons 15

Left and Right buttons 15

Touchscreen buttons 15

Getting started 16

To turn the display on 16

To adjust the display 17

To turn on the backlight 17

Using the remote control to control your equipment 18

Home 18

Device menu 19

Control panels 21

Use mode 22

To switch devices without affecting the source 23

3 Customizing the intelligent remote control 25

To customize the remote control 25

Understanding modes 28

To switch modes 29

To show or hide the Mode menu 29

5

Learning commands from other remote controls

(Learn mode) 30

To program a button on the display (soft button) 31

To program an item on the Device menu 34

To program a template button 36

Programming the direct-access and Left/Right buttons 37

To program a button globally 37

To program a direct-access button on a per-device basis 38

Adding devices to your system (Add mode) 39

To add a device 39

Relabeling buttons and menu items (Label mode) 41

To relabel a button 41

To relabel an item on a menu 43

Rearranging items in menus (Move mode) 44

To rearrange the items in a menu 44

Deleting buttons and menu items (Delete mode) 46

To delete a button or button action 46

To delete a device, Device menu action, or macro group 47

4 Creating Macros 50

Recording macros 52

To record a macro 52

To view the commands in a macro 57

Editing macros 57

To edit a previously recorded macro 57

Organizing macros into groups 59

To add a macro group 59

Using macros 61

To execute a macro 61

To stop a macro 61

5 Settings 62

To adjust settings 62

To exit Setup 65

6

6 Troubleshooting 66

Problems using the remote control 66

Problems using the recharging dock 69

Common questions 70

Additional procedures 71

To reset the remote control 71

To revert to the original conﬁguration 72

To calibrate the touchscreen 72

Service and support 73

7 Specifications 74

8 Command Reference 75

Welcome

7

Welcome

Congratulations on purchasing the intelligent remote control. The remote

control is a universal learning remote control that combines ﬂexibility with ease

of use through an LCD touchscreen and an intuitive user interface.

COMPLETE CUSTOMIZATION

You decide how you want the remote control to look. You can add and remove

devices and functions. You can relabel buttons using the remote control’s

unique virtual keyboard. You can record all the macros you need, and edit them

on-screen. The remote control is as individual as you are.

TOTAL CONTROL

While other universal remotes conﬁne you to a predeﬁned list of devices, the

remote control lets you add, delete, reorganize, and even relabel new devices, so

it grows with your system. It can learn to control any device that understands

infrared signals, from your TV to your remote-control curtains. The built-in

device templates make it easy to add and program all kinds of devices.

SIMPLICITY AND DEPTH

The remote control’s elegant interface is simple enough for the entire family to

use. Yet it has the power and ﬂexibility to satisfy any home entertainment or

home control enthusiast.

The remote control and

recharging dock

8

Welcome

Features

The intelligent remote control

• Large dynamic touchscreen with liquid crystal display.

• Direct-access buttons for frequently used functions.

• Elegant, intuitive interface with animation (patent pending).

• Automatic backlighting for visibility in the dark.

• Built-in, customizable device templates for total control.

• Programmable, editable macros (patent pending).

• Virtual keyboard for labeling buttons and devices (patent pending).

• Can control any device that receives infrared remote control signals.

• Learns infrared (IR) codes from your existing remote controls—then replaces

those remotes.

• Comes with hundreds of built-in commands (RC-5/6) for out-of-the-box use

with your Philips and Marantz components.

• Designed for one- or two-handed operation, or tabletop use.

• Flash memory stores your commands even when batteries aren’t present.

Recharging dock

• Easy, unlimited recharging—no need to remove the battery.

• The remote control can be used while it’s on the dock,

even if the battery is low.

• NiMH rechargeable battery pack minimizes loss of battery life over time.

• Rechargeable battery pack is easier on the environment than ordinary

batteries that need replacing.

• Indicator light tells you when the remote control is charging.

PC serial cable

• To connect the remote control with your computer.

• Allows you to customize the graphical user interface through PC software.

CHAPTER 1

Chapter 1—Batteries

9

1

Batteries

The remote control uses four AA batteries or the rechargeable battery pack

supplied with the recharging dock. If you purchased the recharging dock, see

“Using the recharging dock” on page 11.

Installing AA batteries

•

Install four AA batteries as shown.

Slide the battery cover

off the back of the

remote control.

Insert 4 AA batteries

as shown. Improper

installation could damage

the remote control.

When you’re done, slide

the battery cover back

on. The remote control

starts up automatically,

and the word “remote

control” appears on the

display. After a few

seconds, the remote

control beeps twice to

indicate that it’s ready to

use.

10

Chapter 1—Batteries

NOTE

If the display is too light or too dark, adjust the contrast. (See page 14.)

BATTERY LIFE

When the batteries are running low, the Low Battery icon blinks at the

center top of the display. The remote control may continue to operate your

equipment with low batteries. However, you won’t be able to use the remote

control’s learning or customizing features until the batteries have been replaced.

This prevents the remote control from accidentally losing custom commands if

it’s in a customization mode when the batteries run out.

TIP

To preserve battery life, set the LCD backlight to stay on very brieﬂy (20

seconds or less). For instructions, see Chapter 5, “Settings.”

IF THE BATTERIES RUN OUT

The remote control will retain your commands and settings in memory even

after the batteries run out. However, you should replace the worn batteries with

a fresh set as soon as possible.

After replacing batteries, you’ll need to set the clock to the current time. For

instructions, see Chapter 5, “Settings.”

Using the recharging dock

11

Using the recharging dock

The recharging dock comes with a rechargeable battery pack.

You should fully charge the battery pack before using the remote control.

Slide the battery cover

off the back of the

remote control.

Remove the AA battery

tray (the ridged piece of

plastic at the back of the

battery compartment).

AA battery tray

12

Chapter 1—Batteries

When you insert the battery pack, the remote control starts up automatically,

and the word “remote control” appears on the display. After a few seconds, the

remote control beeps twice to indicate that it has ﬁnished starting up. Now

you’re ready to charge up the battery.

Orient the battery pack

as shown. The label

should face outward, and

the plastic tabs on the

battery pack should be

aligned with the notches

in the sides of the battery

compartment.

Insert the battery pack

You will need to press

firmly.

When you’re done, slide

the battery cover back

on. You’re ready to

charge up the battery.

Notches

Plug the power adapter

into a wall outlet and

connect it to the

recharging dock.

Recharging dock

Power adapter

Using the recharging dock

13

The light on the front of the recharging dock turns off when the batteries are

fully charged. The charging time is 2 to 3 hours, depending on the condition of

the battery pack. It’s a good idea to place the remote control on the recharging

dock when you’re not using it.

When the battery is running low, the Low Battery icon blinks at the center

top of the display. The remote control may continue to operate your equipment

with low batteries. However, you won’t be able to use the remote control’s

learning or customizing features.

IMPORTANT

Use the recharging dock only with the NiMH rechargeable

battery pack. The dock won’t recharge ordinary AA batteries, and if AA batteries

are installed, the remote control can’t get power from the dock while resting on

it.

Place the remote control

on the recharging dock.

Light is on while

battery is

charging.

You can use the remote

control while it’s being

recharged. The battery

will not run down.

CHAPTER 2

14

Chapter 2—Using the remote control

2

Using the remote control

This chapter shows you how to use the remote control to operate your equipment.

Buttons and controls

Light sensor

Left button

Learning eye

Right button

Touchscreen

Sending eye (IR transmitter)

Direct-access buttons

Battery cover

Recharging

contacts

Reset button

Contrast

dial

Backlight

button

Serial port

(for future

upgrades)

Buttons and controls

15

Direct-access buttons

The buttons labeled

Mute

,

Channel

, and

Volume

are

direct-access buttons

. The

direct-access buttons make these frequently used functions available even when

the touchscreen is off. You can program them so that they always operate the

same component—for example, the TV. Or, you can program them to operate

different devices at different times.

Left and Right buttons

The Left and Right buttons change function depending on the device the

remote control is controlling. Labels displayed above them on the touchscreen

show their current function.

Touchscreen buttons

Buttons on the touchscreen let you control particular devices. You activate the

buttons by tapping them with your ﬁnger.

Labels show

current function of

Left and Right

buttons. Functions

can vary depending

on device.

Left button

Right button

VCR is the current

device.

16

Chapter 2—Using the remote control

WHICH BUTTONS CAN BE PROGRAMMED?

Direct-access buttons, Left and Right buttons, and buttons on the touchscreen

can all be programmed. You can set the direct-access and Left/Right buttons to

always perform the same function. Or, you can program them to perform

different functions depending on the device. For instructions, see “To program

a button globally” on page 37.

Getting started

To turn the display on

•

Touch the screen with your finger, then let go.

This is called

tapping

the screen.

NOTE

There’s no need to turn the remote control off. The display shuts off

automatically a few seconds after you stop using the remote control. To change

how long the display stays on, see Chapter 5, “Settings.”

When the remote control is new, it displays the ﬁrst panel of Home. From

Home, you can choose devices to control; for more information, see “Home”

on page 18. (If your dealer or installation technician has conﬁgured the remote

control, you might see a different screen when you turn on the display.)

Gently tap anywhere

on the touchscreen to

turn on the display.

Getting started

17

To adjust the display

•

Turn the contrast dial (on the left side of the remote control).

To turn on the backlight

•

Press the backlight button (on the left side of the remote control).

Pressing the backlight button also turns on the display (if it is not already on).

The backlight shuts off automatically after a few seconds to save power. To keep

the backlight on, hold the backlight button down.

In low-light conditions, the remote control switches the backlight on

automatically whenever you tap the touchscreen. You can adjust the sensitivity

of the remote control’s light sensor and the length of time the backlight stays

on. For instructions, see Chapter 5, “Settings.”

BE KIND TO YOUR LCD TOUCHSCREEN

Take the following precautions when using the remote control:

• Tap the LCD touchscreen

gently

. Never use force.

• Do not use a pen or any sharp object to tap the screen; you might damage the

surface. If you like, you can use a blunt object such as a pencil eraser or the

cap of a pen.

• Keep the touchscreen dry. Wipe off any spills immediately. The remote

control is not waterproof; never immerse it in liquid.

• Don’t expose the remote control to extreme temperatures. Keep it away from

heat sources.

• Avoid dropping the remote control.

• Don’t drop anything on the touchscreen; it’s made of glass.

• Clean the LCD touchscreen with a soft cloth. If needed, dampen the cloth

slightly before cleaning. Never use abrasives or cleaning solutions.

18

Chapter 2—Using the remote control

Using the remote control

to control your equipment

NOTE

The remote control is preprogrammed to work with popular

components made by Philips, Marantz, and certain other companies. If the

remote control doesn’t operate your components, you will need to teach it; for

instructions, see “Learning commands from other remote controls (Learn

mode)” on page 30. However, if a dealer or installer has programmed the remote

control for you, it should operate all your components.

Home

When you ﬁrst tap the touchscreen, Home is diplayed. Here you’ll ﬁnd a

button for each of the devices that the remote control is set up to operate.

Tap one of the buttons to choose a device.

NOTE

If your components are connected to a preampliﬁer, receiver, or similar

device, choosing a device from Home may automatically switch the input source

to the chosen device. You can control this behavior; for more information, see

“To program an item on the Device menu” on page 34.

GOING BACK HOME

The purpose of Home is to make navigating easy. The device buttons in Home

are set up for you automatically when you add devices to your system or remove

them. You can go back home at any time by pressing the Home button .

Tap a device ... ... the remote control displays

a control panel for the device.

Home

Page is loading ...

Philips intelligent remote control User manual

Philips intelligent remote control User manual

Related papers

Other documents